BDI CORRIDOR SV BAR 5621 User manual

CORRIDOR®SV BAR 5621
BAR CABINET
DESIGN MATTHEW WEATHERLY
LET’S GET STARTED.
INSTRUCTION MANUAL

BDIUSA.COM | 3NEED ASSISTANCE? [e-mail]
Congratulations on the purchase of your Corridor SV Bar 5621 from BDI. Your bar cabinet
has been designed to provide a lifetime of enjoyment. This manual will provide you with
assembly instructions and other helpful information to ensure you get the most out of
your product. Please save it for future reference.
Your Corridor SV Bar has been engineered for simple assembly. Please follow these
directions carefully to prevent any damage.
Should you need further assistance, contact BDI at customerservic[email protected].
ENJOY!

4 | BDIUSA.COM CORRIDOR SV BAR 5621
HARDWARE AND COMPONENTS
Hex Wrench (T1) QTY: 1 M6 x 70 Screw (H1) QTY: 8
M6 x 12 Screw (H2) QTY: 16 M4 x 30 Screw (H3) QTY: 4 Rubber Bumper (H4) QTY: 12
Cabinet (C1) QTY: 1 Leg (C3) QTY: 2
Upper Frame (C2) QTY: 1
Phillips Screwdriver
TOOL REQUIRED (NOT INCLUDED)
Unpack and identify the parts listed below. If you are missing any hardware, please contact BDI
Customer Service at customerservic[email protected]. For all other concerns, please contact your
BDI retailer.
The assembly workspace should be a non-marring surface such as carpet. Do not use power tools
for the assembly of this product.

BDIUSA.COM | 5NEED ASSISTANCE? [e-mail]
Lower Frame (C4) QTY: 1
Bottom Shelf (C5) QTY: 1
Top Panel (C6) QTY: 1
Glass Shelf (C7) QTY: 2 Door Pull (C8) QTY: 2
HARDWARE AND COMPONENTS

6 | BDIUSA.COM CORRIDOR SV BAR 5621
STEP 1. ATTACH UPPER FRAMEASSEMBLY
Place Cabinet (C1) upside down on a soft, flat
surface. Place the Upper Frame (C2) on the
Cabinet (C1), paying careful attention the side
hole orientation. Attach with 8 Screws (H1).
Tighten with Hex Wrench (T1).
HEX WRENCH – T1 QTY
1
SCREW – H1 QTY
8
Hole orientation
C1
C2
H1
H1
H1
H1

BDIUSA.COM | 7NEED ASSISTANCE? [e-mail]
ASSEMBLY
STEP 2. ATTACH LEGS
Attach Legs (C3) to Upper Frame (C2) using
8 Screws (H2). Tighten with Hex Wrench (T1).HEX WRENCH – T1 QTY
1
SCREW – H2 QTY
8
C2
H2
H2
C3
C3

8 | BDIUSA.COM CORRIDOR SV BAR 5621
STEP 3. ATTACH LOWER FRAMEASSEMBLY
With help from another person, hold the Lower
Frame (C4) in place and attach it to the Legs (C3)
using 8 Screws (H2).
Ensure that the "Top" label on the Lower
Frame (C4) will face up when the Cabinet is
flipped over. Tighten with Hex Wrench (T1).
HEX WRENCH – T1 QTY
1
SCREW – H2 QTY
8
C3
C3
C4
H2
H2
2 PERSON TASK

BDIUSA.COM | 9NEED ASSISTANCE? [e-mail]
ASSEMBLY
With help from another person, carefully flip the Cabinet over to its upright position. Shelf pins can be
repositioned where desired. Once shelf pins are installed, place the Drawer Liner (C7) in the drawer.
C7
ASSEMBLY
STEP 4. INSTALL SHELF PINS & DRAWER LINER
Shelf pins

10 | BDIUSA.COM CORRIDOR SV BAR 5621
STEP 5. INSTALL GLASS SHELVES & DOOR PULLSASSEMBLY
Install the Glass Shelves (C8) by slightly tilting
them, sliding them in, and resting them on the
Shelf Pins (H3).
Attach the Door Pulls (C9) to the doors using
4 Screws (H3). Tighten with Phillips Screwdriver
(not included).
PHILLIPS SCREWDRIVER
NOT INCLUDED
QTY
1
SCREW – H3 QTY
4
C8
C8
C9
C9
H3
H3

BDIUSA.COM | 11NEED ASSISTANCE? [e-mail]
ASSEMBLY
STEP 6. INSTALL RUBBER BUMPERS, BOTTOM SHELF & TOP PANEL
Attach the 6 adhesive-backed Rubber Bumpers
(H4) to the top of the Cabinet (C1), then attach
6adhesive-backed Rubber Bumpers (H4) to the
top of the Lower Frame (C4). Paying attention
to the labels on the underside of the glass
pieces, place the Bottom Shelf (C5) and To p
Panel (C6) on top of the Rubber Bumpers (H4).
RUBBER BUMPERS– H4 QTY
12
H4 H4 H4
H4 H4 H4
C1
C5
C6
H4
H4
C4
H4
H4

12 | BDIUSA.COM CORRIDOR SV BAR 5621
MOVING DRAWER TO OPPOSITE SIDE
To move the Drawer to the other side, follow these steps.
Fully extend the Drawer and slide the plastic tabs inwards. They are found near the ends of the
slides on the underside. Gently lift the front of the drawer and pull the drawer toward you to
remove it from the sides.

BDIUSA.COM | 13NEED ASSISTANCE? [e-mail]
ASSEMBLY
STEP 7. REMOVE DRAWER SLIDES
Remove the 4 Screws holding the Left Drawer
Slide to the interior wall using a Phillips
Screwdriver.
Set these screws aside for later.
Remove the 4 screws holding the Right Drawer Slide to the metal bracket using a Phillips Screwdriver.
Set these screws aside for later.
PHILLIPS SCREWDRIVER
NOT INCLUDED
QTY
1

14 | BDIUSA.COM CORRIDOR SV BAR 5621
STEP 8. REMOVE METAL BRACKET & ATTACH ON OPPOSITE SIDEASSEMBLY
Remove the 4 screws mounting the Metal
Bracket to the bottom of the cabinet using a
Phillips Screwdriver.
Set these screws aside for later.
Attach the Metal Bracket on the opposite side of the cabinet, reinserting the 4 Bracket Mounting
Screws you just removed into the threaded inserts in the bottom panel of the cabinet. Tighten with
a Phillips Screwdriver.
PHILLIPS SCREWDRIVER
NOT INCLUDED
QTY
1

BDIUSA.COM | 15NEED ASSISTANCE? [e-mail]
Mount the Left Drawer Slide to the Metal
Bracket using 4 of the Drawer Slide Mounting
Screws. Tighten with a Phillips Screwdriver.
Mount the Right Drawer Slide to the interior wall of the cabinet using the remaining 4 Drawer Slide
Mounting Screws. Tighten with a Phillips Screwdriver.
PHILLIPS SCREWDRIVER
NOT INCLUDED
QTY
1
ASSEMBLY
STEP 9. MOUNT DRAWER SLIDES ON OPPOSITE SIDE

16 | BDIUSA.COM CORRIDOR SV BAR 5621
STEP 10. INSTALL DRAWERASSEMBLY
Gently place the drawer back on the drawer slides. Slide the drawer all the way back until it drops
in place and sits flush on the drawer slides.

BDIUSA.COM | 17NEED ASSISTANCE? [e-mail]
ASSEMBLY
STEP 11. SECURE DRAWER INTO PLACE
Push the plastic pins found near the ends of the drawer slides back into their place. This will secure
the drawer in place on the slides.

18 | BDIUSA.COM CORRIDOR SV BAR 5621
CARE & MAINTENANCE
Your BDI furniture has been constructed with the finest materials, manufactured with care and is
designed to last a lifetime. Regular care of your furniture will prolong your enjoyment and keep it
looking its best. Here are some general tips for taking care of BDI furniture. Your surfaces may vary.
GLASS
The glass surface is maintained using household glass cleaner and a paper towel or cloth.
SATIN-ETCHED GLASS
This uniquely smooth-to-the-touch glass surface can be regularly maintained using household glass
cleaner and a paper towel or cloth. Minor scratches or scuffs not eliminated using paper towel or
cloth can usually be removed by using a ‘Magic Eraser’. Magic Eraser is a melamine foam product
available at any grocery store or home improvement center. Dampen the entire glass surface and the
Magic Eraser, then rub the entire glass surface in broad, even strokes using moderate pressure. Clean
and dry the surface with a paper towel. Check for results and repeat as necessary.
Any scratches or scuffing not eliminated by one of the above methods can often be addressed by
‘refreshing’ the glass. This is a process that should not be required more than once per 6-12 months.
See this brief video for the simple method: www.bdiusa.com/glass
WOOD
Wood surfaces should be cleaned with a slightly damp (not saturated) cloth or paper towel. Do not
use glass cleaner on wood. If moisture remains, dry the surface with another cloth. If needed, a
gentle non-abrasive cleanser may be used, but be sure to wipe away all cleaner residue and dry the
surface with a cloth.
BDI’s wood finishes feature natural hardwood solids and veneers. Wood is a product of nature and—
unlike man-made materials that can be manufactured to strict and consistent specifications—has
natural imperfections that are part of its appeal and character. Every piece of wood differs from
every other, even when coming from the very same tree. As such, variation in grain, texture and tone
should be expected from one panel or piece of furniture to the next.
While BDI’s stained wood finishes are stable in tone & appearance, all finishes are subject to some
degree of discoloration with prolonged exposure to direct sunlight. Please take care to avoid
positioning your BDI cabinet in any area with extensive direct sunlight. To learn more about the
features of natural wood, visit www.bdiusa.com/wood
METAL, PORCELAIN, & PAINTED SURFACES
Surfaces should be cleaned with a slightly damp (not saturated) cloth or paper towel. If moisture
remains, dry the surface with another cloth. If needed, a gentle non-abrasive cleanser may be used,
but be sure to wipe away all cleaner residue and dry the surface with a cloth.

BDIUSA.COM | 19NEED ASSISTANCE? [e-mail]
WARRANTY
PRODUCT REGISTRATION
BDI warrants to the original purchaser that for the below-stated warranty term, BDI will repair or
replace any product, part, or component covered by this warranty that fails under normal use as a
result of a defect in material or workmanship. BDI will repair or replace the aforementioned product,
part or component with a comparable product, part or component. The decision to repair or replace
will be at BDI’s sole discretion.
BDI furniture is warranted for three (3) years from the date of purchase as shown on your sales
receipt. The warranty period starts from the date of purchase. This warranty extends only to the
original purchasers who acquire new products from BDI Authorized Resellers. Any product, part,
or component must have been assembled, installed, used, and maintained according to BDI’s
published instructions to be eligible for warranty coverage. Any modification to the original
product voids the warranty.
To view BDI’s complete warranty information, visit www.bdiusa.com/warranty
Registering your new BDI product allows us to send you important product updates, service
information, and helpful hints related to your BDI products. Register today, and you will be entered
to win free a BINK table from BDI: www.bdiusa.com/register

These distinctive product configurations are protected by US and international patents, trade
dress, and/or copyright laws. Corridor & BDI are trademarks of Becker Designed, Inc. All rights
reserved. ©2022, BDI | V.10.21.2022
Made in China