BEA IXIO-ST INDUSTRIAL User manual

E
R
L
A
U
B
T
Z
E
R
T
I
F
I
Z
I
E
R
U
N
G
N
A
C
H
EN 16005
E
N
A
B
L
E
S
A
C
C
O
R
D
A
N
C
E
W
I
T
H
1
3
4
5
6
2
7
IXIO-ST
E
R
L
A
U
B
T
Z
E
R
T
I
F
I
Z
I
E
R
U
N
G
N
A
C
H
DIN 18650
E
N
A
B
L
E
S
A
C
C
O
R
D
A
N
C
E
W
I
T
H
1. LCD
2. AIR-curtain width adjustment
3. AIR-lenses
DESCRIPTION
4. cover
5. main connector
6. main adjustment knob
7. AIR-curtain angle adjustment knob
ENGLISH
Safety sensor
for automatic sliding doors
User’s Guide for product version 0100 and higher
See product label for serial number
ACCESSORIES
BA: Bracket Accessory
(according to EN 16005 and DIN 18650)
RA: Rain Accessory

1
max. 5 cm
2
max.
5 cm**
max.
9 cm**
12-24 V
AC-DC
*
*
**
2
DIN 18650
BS 7036
EN 16005
3,50 m
3 m
2,50 m
2 m
d max = 2,5 m d max = 3 m
3,50 m
3 m
2,50 m
2 m
MOUNTING & WIRING
TIP!
Wiring is compatible with the IRIS.
GREEN
BROWN
YELLOW
WHITE
PINK
GREY
RED
BLUE
POWER SUPPLY
OPENING INPUT
SAFETY INPUT
TEST
OUTPUT
* Output status when sensor is operational
** For compliance with EN 16005 and DIN 18650,
connection to door controller test output is required.
OR
TIP! Alternatively, the
Spotfinder can help locating
the position of the curtains.
WIDTH
TIP!
Additional
adjustments
are possible by
LCD or remote
control
(see p. 5)
Part of the emitted field can be masked to reduce the detection field.
The arrow position determines the width of the detection field.
PUSH
2X
SAFETY FIELD
CLOSER
AWAY
If necessary, adjust the AIR-
curtain angle (from -7° to 4°).
Activate the visible spots.*
DOOR
DOOR
ANGLE
* Visibility depends on external conditions
** The distance between the inner curtain of the inside door sensor and the inner curtain of the outside door sensor should
always be smaller than 20 cm. The distance to the door leaf depends therefore on the thickness of the door leaf.
SENSOR
Always verify the actual detection field width
with a piece of paper and not the Spotfinder,
which detects the whole emitted field.
The size of the detection field varies according to the
mounting height of the sensor.
The full door width must be covered.
Mounting
height Detection
width
2.00 m
2.20 m
2.50 m
3.00 m
3.50 m
2.00 m
2.20 m
2.50 m
d max
d max
3.50 m
3 m
2.50 m
2 m
d max = 2.5 m
3.50 m
3 m
2.50 m
2 m

4
+
3
3
QUICK SETUP = ASSISTED SETUP =
SETUP
OPEN+CLOSE
OR
IMPORTANT! Test the good functioning of the installation before leaving the premises.
LONG PUSH
(> 3 S)
SETTINGS
IMPORTANT!
Step out of the detection field
before launching a setup.
OR
STANDARD: inside installations
CRITICAL ENVIRONMENT: critical or outside installations
SHOPPING STREET: installations in narrow streets with pedestrian traffic
Adjust the sensor by LCD or remote control (see p. 4 and 5)
or choose one of the presettings:

4
Pressing a parameter symbol on your
remote control, displays the saved
value directly on the LCD-screen.
HOW TO USE THE LCD?
To adjust contrast, push and turn
the grey button simultaneously.
During normal function only.
PUSH
TO SELECT
PARAMETER
SCROLL
MENU
UP-DOWN
Select Back to return
to previous menu or
display.
Select More to go to next level:
- basic settings
- advanced settings
- diagnostics
Negative display = active output
displayed value = saved value
Select your language before entering
the first LCD-menu.
During the first 30 seconds after power-on of
the sensor or later in the diagnostics menu.
displayed value = factory value
CHANGING A VALUE
SCROLL
VALUES
UP-DOWN
PUSH
TO SAVE
NEW VALUE
VALUE CHECK WITH REMOTE CONTROL
DISPLAY DURING NORMAL FUNCTIONING
FACTORY VALUE VS. SAVED VALUE
NAVIGATING IN MENUS
Scroll menu items
Push to enter
the LCD-menu
new value is
displayed
more values are
displayed
current value is
displayed
Opening
impulse
Safety

12
AB
+
0 1 2 3 4 5 6 7 8 9
5
NO
NC
NC
NC
NC
NO
NO
NO
OVERVIEW OF SETTINGS
Back
More
AIR: WIDTH
AIR: NUMBER
AIR: PRESTIME
AIR: OUTPUT
REDIRECTION
FACTORYRST
More
Back
Back
More
PRESETTINGS
AIR: IMMUNITY*
AIR: FREQ
More
Back
ZIP all parameter settings in zipped format
ID # unique ID-number
ERROR LOG the last 10 errors
AIR: SPOTVIEW view of spot(s) that trigger detection
AIR: C1 ENERG signal amplitude received on curtain 1
AIR: C2 ENERG signal amplitude received on curtain 2
POWERSUPPLY supply voltage at power connector
OPERATINGTIME power duration since first startup
RESET LOG delete all saved errors
RC PASSWORD password for remotre control login
LANGUAGE language of LCD-menu
ADMIN enter code to access admin mode
low normal
> 2.8 m
high
> 2.8 m
standard critical
env.
shopping
street
normal
< 2.8 m
high
< 2.8 m
For conformity to EN 16005 and DIN 18650 at a mounting height
of 2.8 m or more, values 2 and 3 are not allowed.
Sensors mounted close to each other should have a different
frequency.
increased immunity
increased immunitiy + 1 curtain
factory values
service
mode
motion 15 s 30 s 1 min 2 min 5 min 10 min
safety safety
+
opening
0 presence detection on safety input
1 presence detection on safety and opening input
20 min 60 min infinite
service mode = no IR detection during 15 minutes (maintenance).
This value excludes conformity of the door system to EN 16005 and DIN 18650.
restore to factory values
min. value for DIN18650: 1 min
min. value for EN16005: 30 s
BASICADVANCED
DIAGNOSTICS
Always additionally adjust
the arrow position on the
sensor with a screwdriver.
* For conformity to BS 7036 at a mounting height of 2.2 m or more,
values 2 and 3 are not allowed.

2
1
4
5
1
2
1
2
1
2
1
1
1
2
1
2
1
2
1
1
2
1
2
2
2
6
8
1
E1
E2
E4
E5
E8
TROUBLESHOOTING
The ORANGE LED
flashes 1 x.
The ORANGE LED
flashes 2 x.
The ORANGE LED
flashes 4 x.
The ORANGE LED
is on.
The RED LED flashes
quickly after an
assisted setup.
The RED LED
lights up
sporadically.
The LED and the
LCD-display are off.
The reaction of
the door does not
correspond to the
LED-signal.
The sensor signals
an internal fault.
The power supply is too
low or too high.
The sensor receives
not enough AIR-energy.
The sensor encounters
a memory problem.
The sensor vibrates.
The sensor sees the door
during the assisted setup.
The sensor sees the door.
The sensor is disturbed
by external conditions.
Check power supply (in the diagnostics menu of the LCD).
Check wiring.
Check the angle of the AIR-curtains.
Increase AIR-immunity filter to value 4 or 5 (> 2.8 m).
Cut and restore power supply.
If orange LED lights up again, replace sensor.
Check the angle of the AIR-curtains.
Launch a new assisted setup.
Attention: Do not stand in the detection field!
Check output configuration setting.
Check wiring.
Check if the sensor is fastened firmly.
Check position of cable and cover.
Increase the AIR-immunity filter to value 3.
Select presetting 2 or 3.
Launch an assisted setup and adjust the AIR angle.
Cut and restore power supply.
If orange LED flashes again, replace sensor.
Cut and restore power supply.
Check wiring.
The ORANGE LED
flashes 5 x.
The sensor receives
too much AIR-energy.
Check the angle of the AIR-curtains.
Decrease the AIR immunity filter to value 1, 2 or 3.
LED flashes LED flashes
quickly LED is off
The ORANGE LED
flashes 8 x.
The AIR power emitter is
faulty.
Replace sensor.

7
INSTALLATION
Avoid extreme
vibrations. Do not cover the sensor. Avoid moving objects
and light sources in
the detection field.
Avoid highly
reflective objects in
the infrared field.
It is recommended to clean
the optical parts at least once
a year or more if required due
to environmental conditions.
Do not use aggressive
products to clean
the optical parts.
• The device cannot be used for purposes other than its intended use. All other uses cannot be
guaranteed by the manufacturer of the sensor.
• The manufacturer of the door system is responsible for carrying out a risk assessment and installing the
sensor and the door system in compliance with applicable national and international regulations and
standards on door safety.
• The manufacturer of the sensor cannot be held responsible for incorrect installations or inappropriate
adjustments of the sensor.
Only trained and
qualified personnel
may install and setup
the sensor.
The warranty is invalid if
unauthorized repairs are
made or attempted by
unauthorized personnel.
Always test the good
functioning of the
installation before
leaving the premises.
The door control unit
and the door cover
profile must be correctly
earthed.
MAINTENANCE
SAFETY

BEA SA | LIEGE Science Park | ALLÉE DES NOISETIERS 5 - 4031 ANGLEUR [BELGIUM] | T [phone] | F [phone] | [email protected] | WWW.BEA.BE
©BEA | Original instructions | 42.7608 / V2 - 09.12
TECHNICAL SPECIFICATIONS
Supply voltage:
Power consumption:
Mounting height:
Temperature range:
Degree of protection:
Expected lifetime:
Applicable directives:
Presence
Typical response time: < 200 ms (max. 500 ms)
Active infrared with background analysis
Spot: 5 cm x 5 cm (typ)
Number of spots: max. 24 per curtain
Number of curtains: 2
Solid-state-relay
(potential and polarity free)
Max. contact current: 100 mA
Max. contact voltage: 42 V AC/DC
Holdtime: 0.3 to 1 s
Sensitivity: Low: < 1 V; High: > 10 V (max. 30 V)
Response time on test request: typical: < 5 ms
EN 12978
EN ISO 13849-1:2008 PL «c» CAT. 2
(under the condition that the door control system
monitors the sensor at least once per door cycle)
EN 16005:2012 Chapter 4.6.8;
DIN 18650-1:2010 Chapter 5.7.4
BS 7036-1:1996 Chapter 8.1
Detection mode:
Technology:
Outputs:
Test input:
Norm conformity:
Specifications are subject to changes without prior notice.
All values measured in specific conditions.
12 V - 24 V AC +/-10% ; 12 V - 30 V DC +/-10% (to be operated from SELV compatible power supplies only)
< 2.5 W
2 m to 3.5 m (local regulations may have an impact on the acceptable mounting height)
-25°C to +55°C; 0-95% relative humidity, non condensing
IP54
20 years
EMC 2004/108/EC; MD 2006/42/EC; RoHS 2002/95/EC
PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOUR PRINTING
BEA hereby declares that the IXIO-ST is in conformity with the basic requirements and the other relevant provisions of the directives
2004/108/EC and 2006/42/EC.
Notified Body for EC-type inspection: 0044 - TÜV NORD CERT GmbH, Langemarckstr. 20, D-45141 Essen
EC-type examination certificate number: 44 205 12 405836-001
Angleur, June 2012 Jean-Pierre Valkenberg, authorized representative and responsible for technical documentation
The complete declaration of conformity is available on our website: www.bea-pedestrian.be
Only for EC countries: According to the European Guideline 2002/96/EC for Waste Electrical and Electronic Equipment (WEEE)