Becca E100M User manual

INSTALLATION GUIDE
E100M Waterborne Spray Gun Cleaner
Featuring Clarifier Recycling System
Technical Assistance call [phone]

Jul 2011, V 1.0 2Installation Guide E100M
TOOLS REQUIRED
Phillips Screw Driver for all Screws on the unit &
pallet
Flat Screw Driver or Snips for removal of Staples
and strapping materials
UNPACKAGING THE UNIT
Step 1: Carefully inspect the shipping carton
for any signs of transport damage. If damage
has occurred contact the shipping company
and BECCA Inc. immediately.
Step 2: Begin by removing the staples
attaching the box to the skid.
Carefully remove your Spray Gun Cleaner
from the shipping carton.
Remove the shrink wrap and strapping
materials.
Remove the unit from the palette and place it
in the general area for installation.
You are ready to begin with the installation of
the Spray Gun Cleaner.
Step 3: Remove the cover

Jul 2011, V 1.0 3Installation Guide E100M
Step 2: Remove the packaging material
Step 3: Place the Following:
a) Flow Brush into clip in center of
the wash basin
b) Place the magnet with hook on the
side of the unit (leave white cover
on the magnet)
c) Attach the POWERPISTOL to the
magnet hook
d) Place blue lines with QD’s into
receptacles
e) Remove the Foot Pedal from the
rear of the unit and place it on the
floor next to the front corner of the
unit

Jul 2011, V 1.0 4Installation Guide E100M
Step 4: Install a fitting into the ball valve on
the air regulator that is compatible with the
shop air (due to a variety of applications, this
part is not supplied by BECCA).
Connect the shop air to the ball valve (with
the Ball valve in the “Off” position).
Step 5: Check large white drain hose to be
sure is attached through the lid of the
container.
Check small white suction hose to be sure it
is all the way down to the spacer.
Attach Bubbler to the clip located on the
door.
.
.

Jul 2011, V 1.0 5Installation Guide E100M
Step 6: Pour 5 Gallons of distilled water (or
approved paint company waterborne gun
cleaning solution) slowly into the sink with
one well shaken bottle of BECCA Water
Wave additive.
Step 7: Turn on ball valve to apply air to the
system and adjust all air and fluid flow levels.
You are ready to use the BECCA E100M
Spray Gun Cleaner
Keep the cover over the cleaning area
when not in use.
See Page 7
We suggest that the recommended Spray
Gun Cleaning Procedures be reviewed
with everyone using the new E100M.
There are some major differences
compared to solvent gun cleaning.

Jul 2011, V 1.0 6Installation Guide E100M
BECCA Inc. Recommended Spray Gun Cleaning Procedure
9Clean the gun as soon as possible after using it
9Dispose of the paint left in the gun into an approved waste container
9Rinse the gun with waterborne gun cleaning solution and pour the pre-rinse into
the approved waste container (be sure to trigger gun over container)
9Remove the Air Cap and place it in the gun cleaner
9Attach the quick-disconnect to the gun to protect the air passageway
9Clean the Fluid Tip and Fluid Nipple aggressively with the flow brush
9Power Flush the Fluid Passageway completely with the Power Pistol
9Clean the Air Cap with the Flow Brush, making sure to clean the small holes in
each air horn
9With the air still connected, trigger the gun to expel the solution and blow off the
outer gun and the fluid passageway through the Fluid Nipple
9Blow off the air cap and reconnect it to the gun
9Wipe down outside of gun and disconnect the air quick disconnect
9Do not “chase” the gun with anything - - put it away clean and dry
Tips from the Pro’s
Never use ammonia or any other solvent to do the pre-rinse
The better the pre-rinse process to clear the fluid passageway of raw paint, the
longer the cleaning solution will last between flocculation’s
Keeping the air passageway dry is key to preventing corrosion in the air
passageway - - always attach the air quick-disconnect during the process
Use the flow brush and power pistol aggressively, especially with whites, reds,
and certain blacks, which are harder to remove.
Never “chase” a clean, dry gun with anything
Follow the gun manufacturers instructions - do a periodic detail cleaning

Jul 2011, V 1.0 7Installation Guide E100M
BECCA HEATER SYSTEMS
(Optional)
“Heater5” General Purpose Heater (outside mix room)
“HeaterEXP” Cls I Div 1- Heat on Demand (Inside or outside of mix room
Instructions for set-up and use
Fill with 5 gal. Distilled Water and one bottle of BECCA WaterWave Additive (well
shaken) - - OR - - 5 gal of Paint Co. supplied Waterborne Paint Gun Cleaning
Solution & one bottle of BECCA WaterWave Additive (well shaken)
Program 7 day timer (supplied by BECCA):
1. For Heater5 - turn “ON” 2 hours before shop opens - - and turn “OFF” at
typical shop closing time. (Monday thru Friday or Monday thru Saturday)
2. For HeaterEXP - turn when shop opens - - and turn “OFF” at typical shop
closing time. (Monday thru Friday or Monday thru Saturday)
Plug in timer to electrical outlet - - plug in heater to timer
1. Note: When HeaterEXP is located in Mix room the connection can be any
of the following:
1. Exp Cable supplied can be run through the wall and connected
outside the mix room
2. Exp cable minus the plug can be connected inside the mix room to
an Exp switch or timer (neither are supplied)
Warning!
Evaporation will reduce fluid level - - Check fluid daily and replace as needed.
DO NOT ALLOW FLUID LEVEL TO DROP BELOW HALF-FULL!
The purpose of the BECCA nylon pail liners (part #823203-6) is to protect the
metal container from rusting-out and leaking. DO NOT USE THE HEATER
WITHOUT A PAIL LINER!

Jul 2011, V 1.0 8Installation Guide E100M
WARRANTY INFORMATION / TECHNICAL ASSISTANCE
The Warranty of your system begins with the Certified Start-up by your local BECCA
Distributor. Make sure this is completed and you receive a copy of the Certified Start-up
document.
For more information, prices or technical assistance,
contact your local BECCA distributor or call / fax our
BECCA Care™ Numbers:
2010 Cobb International Blvd Suite H
Kennesaw, GA 30152
Tel: [phone] (U.S.A.) Fax: [phone] (U.S.A.)
Copyright © 2011 by BECCA Inc. All Rights Reserved.
2010 Cobb Intl Blvd Ste H
Kennesaw, GA 30152