Becker CentralControl CC51 User manual

CentralControl
CC51, CC31
en Assembly and operating instructions for op-
eration with the local interface
Central controller
Important information for:
• Fitters / • Electricians / • Users
Please forward accordingly!
These instructions must be kept safe for future reference.
Becker-Antriebe GmbH
Friedrich-Ebert-Straße 2-4
35764 Sinn/Germany
www.becker-antriebe.com
4035 630 147 025/07/2017
4035 630 147 025/07/2017

Table of contents
General ................................................................................................................ 5
Warranty .............................................................................................................. 5
Items included ...................................................................................................... 6
Safety instructions ................................................................................................ 6
Intended use ........................................................................................................ 8
Dimensions .......................................................................................................... 9
Device overview ...................................................................................................10
Start / standard screen.........................................................................................13
Mains connection ................................................................................................14
Explanation of pictograms ....................................................................................14
Explanation of the operator controls ......................................................................16
Operating the house automation with other devices on the home network.................17
Operating the house automation through a device with mobile Internet access from
outside................................................................................................................18
Preparing to commission the CC31 .......................................................................18
Commissioning with the local interface ..................................................................20
Setting the language ...................................................................................... 20
Establishing a network connection................................................................... 21
Setting the time and date................................................................................ 21
Setting the location ........................................................................................ 22
Adding a Centronic receiver ............................................................................ 22
Adding a B-Tronic receiver ............................................................................. 23
Adding a room ............................................................................................... 23
Adding elements to a room ............................................................................. 23
End of commissioning .................................................................................... 23
Building wiring system settings .............................................................................24
Adding a Centronic receiver ............................................................................ 24
Adding a B-Tronic receiver ............................................................................. 24
Deleting a Centronic receiver .......................................................................... 25
Deleting a B-Tronic receiver............................................................................ 25
Renaming a receiver ...................................................................................... 26
Adding a Centronic or B-Tronic transmitter ...................................................... 26
Deleting a Centronic or B-Tronic transmitter .................................................... 26
Renaming a transmitter .................................................................................. 26
Adding a Centronic or B-Tronic sensor ............................................................ 26
Deleting a Centronic or B-Tronic sensor .......................................................... 26
Renaming a sensor ........................................................................................ 26
Adding an internal object ................................................................................ 26
Deleting an internal object .............................................................................. 26
Renaming an internal object............................................................................ 26
Linking a transmitter to a function (adding logic)............................................... 26
Linking a sensor to a function (adding logic) ..................................................... 26
Linking an internal object to a function (adding logic) ........................................ 26
2

My Home settings ................................................................................................27
Adding a room ............................................................................................... 27
Sorting rooms................................................................................................ 27
Deleting a room ............................................................................................. 27
Renaming a room........................................................................................... 27
Allocating elements to a room ......................................................................... 28
Sorting elements in a room ............................................................................. 28
Deleting elements from a room ....................................................................... 28
Adding a group .............................................................................................. 28
Sorting groups............................................................................................... 29
Deleting a group ............................................................................................ 29
Renaming a group.......................................................................................... 29
Allocating elements to a group ........................................................................ 29
Deleting elements from a group ...................................................................... 30
Adding a scenario .......................................................................................... 30
Sorting scenarios........................................................................................... 31
Deleting a scenario ........................................................................................ 31
Renaming a scenario...................................................................................... 31
Allocating elements to a scenario .................................................................... 31
Deleting elements from a scenario .................................................................. 32
Adding a camera............................................................................................ 32
Sorting cameras ............................................................................................ 32
Deleting a camera .......................................................................................... 32
Changing camera settings .............................................................................. 33
Adding a radio ............................................................................................... 33
Sorting radios ................................................................................................ 33
Deleting a radio.............................................................................................. 33
Changing radio settings.................................................................................. 34
Automation settings .............................................................................................34
Setting the memory function (ON/OFF)............................................................ 34
Setting the automatic roof window................................................................... 35
Setting the holiday function............................................................................. 35
Setting the sun protection function .................................................................. 36
Adding a timer ............................................................................................... 36
Changing a timer............................................................................................ 36
Deleting a timer ............................................................................................. 37
Setting the heating functions........................................................................... 37
Access settings ...................................................................................................38
Generating a service code .............................................................................. 38
Setting up remote access for an existing account ............................................. 39
Setting up remote access for a new account .................................................... 40
View settings .......................................................................................................41
Setting the background colour ........................................................................ 41
Setting the visual background effects .............................................................. 41
3

Resetting the background colour and the visual background effects to the factory
settings ......................................................................................................... 41
Information settings .............................................................................................41
System information ........................................................................................ 41
Reading out the error memory ........................................................................ 41
Reading update news ..................................................................................... 42
System settings ...................................................................................................42
Setting the language ...................................................................................... 42
Setting the location ........................................................................................ 42
Setting the time and date................................................................................ 43
Establishing a network connection................................................................... 43
Update.......................................................................................................... 44
Creating a backup.......................................................................................... 44
Restoring from backup ................................................................................... 45
Factory reset ................................................................................................. 45
Reboot.......................................................................................................... 45
Rooms ................................................................................................................46
Setting receivers to Automatic mode ............................................................... 46
Setting all the receivers in the room to Automatic mode..................................... 46
Setting all the receivers in the home to Automatic mode .................................... 46
Setting receivers to Manual mode ................................................................... 46
Setting all the receivers in the room to Manual mode......................................... 46
Setting all the receivers in the home to Manual mode ........................................ 47
Operating receivers........................................................................................ 47
Adding favourites ........................................................................................... 47
Deleting favourites ......................................................................................... 47
Groups................................................................................................................48
Operating groups........................................................................................... 48
Scenarios............................................................................................................48
Operating scenarios....................................................................................... 48
Cameras .............................................................................................................48
Calling up cameras ........................................................................................ 48
Radios ................................................................................................................48
Starting a radio .............................................................................................. 48
Stopping a radio ............................................................................................ 49
Weather forecast .................................................................................................49
Changing the batteries of an external keyboard ......................................................49
Cleaning..............................................................................................................49
Technical data .....................................................................................................50
Technical data for the CC51............................................................................ 50
Technical data for the CC31............................................................................ 51
What to do if...?....................................................................................................52
Simplified EU declaration of conformity..................................................................53
Annex .................................................................................................................53
Astronomical function..................................................................................... 53
4

General
With the B-Tronic CentralControl you can operate the drives and control units with bid-
irectional KNX radio and the Centronic I and II range of controls.
This device uses free/open source software. The source code can be downloaded from
http://www.b-tronic.net/source/. On request, Becker Antriebe will make the source
code available on a CD-ROM at cost price. Please contact [email protected] if you
are interested.
As a result of continuous further development of the software, there can be differences
between the illustrations and your device.
This is not, however, important for any of the procedures described.
Please observe these Assembly and Operating Instructions when installing and setting
up the equipment.
Warranty
Structural modifications and incorrect installation which are not in accordance with
these and our other instructions can result in serious injuries, e.g., crushing of limbs.
Therefore, structural modifications may only be carried out with our prior approval and
strictly in accordance with our instructions, particularly the information contained in
these Assembly and Operating Instructions.
Any further processing of the products which does not comply with their intended use is
not permitted.
The end product manufacturer and fitter have to ensure that all the relevant current
statutory, official and, in particular, EMC regulations are adhered to during utilisation of
our products, especially with regard to end product manufacture, installation and cus-
tomer advice.
5

Items included
CC51 CC31
•B-Tronic CentralControl control unit
•USB WLAN stick
•USB Flash memory stick
•USB Centronic stick
•USB B-Tronic/KNX stick
•Mains adapter
•Fasteners for wall mounting
•Commissioning instructions
•B-Tronic CentralControl control unit
•Flash memory SD card
•USB Centronic stick
•USB B-Tronic/KNX stick
•Mains adapter
•Wireless keypad (incl. USB receiver
stick and batteries)
•Commissioning instructions
Safety instructions
General information
•Please keep the instructions safe!
•Only use in dry rooms.
•Keep people out of the system’s range of travel.
•Keep children away from control units.
•Observe all pertinent country-specific regulations.
•Do not place any objects on the control unit.
•Clean the control unit with a soft, dry, lint-free cloth, and do not use
any chemical cleaning agents.
Caution
•If the system is controlled by one or more transmitters,
the system’s range of travel must always be visible dur-
ing operation.
•Keep packaging materials such as film away from chil-
dren. Misuse can create the risk of suffocation.
6

•Switch the control unit off immediately if the mains ad-
apter and the plug to which it is connected is burnt or
damaged. If a mains adapter is damaged, replace it with
an original one. A faulty mains adapter must not under
any circumstances be repaired.
•Switch the control unit off immediately if the housing of
the control unit is damaged, or if liquids have penet-
rated.
Attention
•Do not let any objects fall onto the control unit.
•If a display is present, protect it against being scratched
by hard objects (e.g. rings, fingernails, wristwatches)
•Wait until the control unit has adjusted to ambient tem-
perature before connecting the control unit to the mains
adapter. Condensation that could lead to a short circuit
can be caused inside the control unit by large differ-
ences in temperature and air humidity.
7

Intended use
The B-Tronic CentralControl may only be used for the operation of suitable drives and
control units with bidirectional KNX radio and with the Centronic I and II range of con-
trols. You can operate a group, or multiple groups, of devices with this controller.
•Please note that radio-controlled systems may not be used in areas
with a high risk of interference (e.g. hospitals, airports).
•The remote control is intended solely for use with equipment and
systems in which malfunctions in the transmitter or receiver would
not pose any risk to persons, animals or property, or which contain
safety devices to eliminate such risks.
•The operator is not protected from interference from other telecom-
munications systems and terminal equipment (e.g. even from radio-
controlled systems which are properly operated in the same fre-
quency range).
•Only connect radio receivers to devices and systems approved by
the manufacturer.
•Ensure that the control unit is not installed or operated
close to metal surfaces or magnetic fields.
•Radio-controlled systems transmitting on the same fre-
quency may cause reception interference.
•Note that the range of the radio signal is limited by legis-
lation as well as by design.
8

Dimensions
All dimensions in mm.
CC51 CC31
156
197 32
28,5 118
118
9

Device overview
CentralControl CC51
5
1
2
3
6
4
109
8
7
13 12 11
14
15
111213
14
16
17
10987
1. Integrated front camera
2. Light sensor
3. Loudspeaker
4. Touchscreen
5. Operating status LED
6. Microphone
7. USB backup memory
8. Free USB connector
9. Centronic stick
10. B-Tronic KNX stick
11. Connection for mains adapter
12. Audio output (3.5 mm jack)
13. WLAN stick
14. Network connection (RJ45)
15. Reset button
16. Cover
17. Feet
10

CentralControl CC31
Connections/slots
21
3
4
5
7 6
8
9
10
11
1. Mains connection
2. LAN connection
3. HDMI connection
4. AV connection
5. YUV connection
6. Free USB 2.0 connection
7. USB connection for B-Tronic KNX stick
8. USB connection for Centronic stick
9. USB connection for keypad stick
10. Card slot for SD card
11. Operating status LED
Rear of the device
MAC-ETH: b4:4a:bc:03:09:aa
Serial: 256854214587
4035 645 019 0
B-Tronic CentralControl CC31
4035 200 019 0
SSID: CC31-XXXX
: WPACC31-YYY
IP: 192.168.31.1
IP20
1
2
1. WLAN wireless network (SSID) 2. WLAN network key (KEY)
11

External keypad
1
2
3
4
5
6
7
9
8
1. Touchpad
2. ON/OFF switch
3. Keypad
4. No function
5. Light button
6. LED light
7. Battery compartment
8. Compartment for keypad receiver
9. Battery compartment cover
12

Start / standard screen
1
3
2
4
65
1 Main screen area
The time and date, and in some cases the weather forecast, are displayed on the main
screen area.
2 Navigation and status area
The current weather, status information, and the navigation elements for the pro-
grammed receivers are shown in the navigation and status area.
3 Time / date
Display of date and time. The time can be displayed in digital or analogue format.
4 Weather
Display of the current weather at the selected weather location. Displaying the
weather data requires an Internet connection.
5 Device status bar
The statuses of various device-specific functions are displayed on this status bar:
B-Tronic KNX stick is available in the device.
B-Tronic KNX stick is not available in the device.
Centronic RF stick is available in the device.
Centronic RF stick is not available in the device.
WLAN signal strength
No WLAN available
13

Network via cable
No network via cable
Access point available
Fault indication
An update is available
The display of blue triangles indicates that more content is available in the
main screen area by scrolling up or down.
6 Main navigation
The main navigation is visible, with an identical format, on all the screens. It consists
of the following three navigation panes:
Clicking this button will always take you back to the start screen.
Clicking this button takes you to the operating facilities for the receivers,
rooms, groups and scenarios.
Clicking this button will take you to the settings.
Mains connection
1. If necessary, pull the cover off the control unit.
2. First connect the mains adapter to the control unit, then plug it into the socket.
3. If you removed the cover, place it back onto the control unit now.
Explanation of pictograms
CAUTION CAUTION indicates a hazardous situation which, if not
avoided, could result in injury.
ATTENTION ATTENTION indicates measures that must be taken to
avoid damage to property.
Denotes user tips and other useful information.
14

All the symbols in square boxes can be found on the screen and should be
operated there using the mouse or touchscreen.
All the symbols in circles provide operating information that should be imple-
mented if a symbol is illustrated in a circle.
Continue with the entries at the point indicated.
Select one or more options from a preset list.*
Fill in one or more text boxes.*
Fill in the text boxes and select the desired options.*
!
Please note the information on the screen.*
The task is complete.
Perform the next step (with and without identification)
Continue, depending on the result of the previous action
“Action not completed successfully” or “Action completed successfully”
*) It may be necessary to scroll down the page to reach all the information, options, in-
put fields, etc.
15

Explanation of the operator controls
The operator controls may execute different functions depending on the receiver type.
Local interface
Move UP/move IN
Switch on the light and increase the brightness
Manually set the temperature higher
STOP button
Switch off the light
Move DOWN, move OUT
Switch on the light and reduce the brightness
Manually set the temperature lower
ON button
OFF button
ON button
Switch on the anti-freeze mechanism/battery energy-saving mode
1
Intermediate position 1 (optional)
Saved light value 1 (optional)
2
Intermediate position 2 (optional)
Saved light value 2 (optional)
Intermediate position with optional closing
Comfort temperature
Eco temperature
16

Local interface
Fold out the foldable roller shutter
Fold up the foldable roller shutter
Operating the house automation with other devices on
the home network
You can use the B-Tronic CentralControl
to “remotely control” home automation
functions using a large number of end
devices that are in your home network.
The devices can be integrated into the
network by means of a network cable a or
WLAN b.
The operating system on which your end
device is based is of no importance. Mi-
crosoft Windows (from XP/Internet Ex-
plorer 8), Android and Apple iOS (Mac,
iPad, iPhone) are amongst the supported
systems.
a
b
To communicate with the central controller over the network, please start your Inter-
net browser and enter the IP number into your browser’s address field.
The entry always starts with “http://” followed by the IP number. This is always repres-
ented by four numbers with at most three digits each, separated by dots.
The entry in the example is: http://192.168.0.52/
You can call up the IP number assigned for your central controller by the network on
the “System information” page:
To access your CentralControl quickly at any time, you can save the page you called
up using the IP address as a favourite or store it on your device’s desktop. To ensure
that a different IP address is not used each time the CentralControl is rebooted, it
should be assigned a fixed IP address (see Establishing a network connection).
17

Operating the house automation through a device with
mobile Internet access from outside
You need to register with the Becker Gate-
way Service for easy remote control of
your central controller over the Internet. A
login code is required once in order to set
up gateway access at www.beckercon-
trol.de.
You will find out how to receive a login
code in the chapter entitled Setting up re-
mote access for a new account or Setting
up remote access for an existing account.
Please note that an Internet connection
and an email account are necessary in or-
der to request a login code. After you
have successfully logged into the Becker
Gateway Service, it is no longer possible
to generate another login code with the
same central controller. You can, of
course, assign a number of central con-
trollers to one user account.
Preparing to commission the CC31
Insert the supplied stick into the B-Tronic CentralControl in accordance with the Device
overview.
There are a number of display options:
•Via television or screen
•Via PC, notebook or tablet
Via television or screen
1. Connect the B-Tronic CentralControl to the television or screen using the HDMI
cable or the AV cable.
2. First connect the mains adapter to the control unit, then plug it into the socket.
Caution
Lay the mains connecting cable in such a way that nobody
can tread on it or trip over it.
18

3. The Start / standard screen [}13] appears.
4. You can now input further entries via the internal keypad, or via the external keypad
supplied.
Via PC, notebook or tablet
There are a number of options:
•WLAN
•Ethernet (an Ethernet cable is not included in the scope of supply)
WLAN
The configuration WLAN of the B-Tronic CentralControl
(access point) is used to make the first connection with
your input device.
1. Make a note of the name of the WLAN wireless network (SSID) and of the WLAN
network key (KEY). Both can be found on the back of the B-Tronic CentralControl.
2. Have the wireless networks shown to you by your input device (PC, notebook or
tablet).
3. Select the WLAN wireless network (SSID) that you noted previously from the list of
available connections and start the connection request.
4. Now enter the WLAN network key (KEY) that you noted previously into the field
provided and connect to the B-Tronic CentralControl. Wait until the WLAN connec-
tion is established.
5. Then open your browser via the input device.
6. Now type the following address into the browser’s address bar:
http://192.168.31.1/ and confirm it by pressing Enter.
7. The start/standard screen appears.
8. Select
9. Now make the settings for your private network.
10. Then set your input device back to the private network.
If you cannot find your CC31 in your network, you must re-
set the CC31 to Hot Spot mode. To do so, press the follow-
ing key combination on the external keypad supplied: ESC
+ Shift + Ctrl. Then repeat the above process.
19

Ethernet (an Ethernet cable is not included in the scope of
supply)
1. Connect the B-Tronic CentralControl to your input device (PC, notebook or tablet)
using the Ethernet cable. Wait until the Ethernet connection is established.
Caution
Lay the Ethernet cable in such a way that nobody can tread
on it or trip over it.
2. Then open your browser via the input device.
3. Now type the following address into the browser’s address bar: http://cc31.local/
and confirm it by pressing Enter.
4. The Start / standard screen [}13] appears.
5. Select
6. You can now input further entries via your input device.
Commissioning with the local interface
The following pages will guide you step-by-step through the installation and configura-
tion of the B-Tronic CentralControl. When all the steps described have been carried
out, your rooms and receivers will be configured and you will be able to centrally control
your home.
However, the B-Tronic CentralControl has significantly more convenience and automa-
tion options available that you can use to adapt your home automation to suit your indi-
vidual needs. These functions are described in detail under the menu items from the
chapter entitled Building wiring system settings [}24].
Setting the language
Local interface
Language
20