Beef Eater Discovery 1100 Series User manual

1100
Outdoor Kitchen
Assembly and Operating Instructions
FOR OUTDOOR USE ONLY
To suit models:
1100s
1100e
1100
3, 4 or 5 Burners For
ALL MODULES

2
Content*:
Bolt Pack Content**
Mrk Qty description Car
ton
1 1 1100 Series BBQ with Hood 1
2 2 Standard Cabinet 2
3 2 Heat Shield spacer 1
4 1 Base Shelf
5 1 Front Guard
Main Parts
Mrk Qty description
A 4 M6 x 30 screw
B 4 M6 x 12 screw
C 4 M4 x 10 screw
D 8 Fiber washer
E 4 M6 Nut
F 1 Rubber grommet
G 12 Medium plastic plug
H 4 Small plastic plug
I 2 Large plastic cover
J 1 Allan Key
Woodland Home Products
3-5 Birmingham Av, Chester-
Hill, NSW, Australia, 2162
Phone: [phone]
Facsimile: 02 9724 8899
E-mail: [e-mail]
Website:
www.beefeaterbbq.com
* The image and assembly procedure refers to
Basic Outdoor Kitchen configuration.
If you have purchased additional modules,
continue to page 6 of this manual for
instructions on how to put them together
and assemble to this Outdoor Kitchen.
** Bolt Pack can be found inside the Base Shelf
carton.
Keep these instructions in a safe place for reference and
for further use.

3
1100Series Outdoor Kitchen Assembly Procedure
Important Note: It is easier to do all assembly work while components are lying on their back, so that they do not need
to be supported in the air. Once completed, the assembly can be brought back upright, leveled and completed.
If choosing to work this way, ensure to remove all loose items from the different parts, and lay back on a padded, flat
and level surface, not too far from where you wish the Outdoor Kitchen to stand.
Step 1
4 x ‘B’, 4 x ‘E’, 8 x ‘D’
Step 2
4 x ‘A’, 4 x ‘E’, 8 x ‘D’
Remove the Hood and all other loose items from inside BBQ, and place it on its back.
Attached the Heat Shield spacer with 2 short screws to each side using nuts.
Position the 2 cabinets on the sides of the BBQ, and attach to the BBQ with 2 screws
through the 2 remaining free holes in Heat Shield spacer on each side. Fasten with nuts

4
Step 3
4 x ‘D’, 4 x ‘B’, 1 x ‘F’
Step 4
4 x ‘C’,
Attach the Front Guard.
You may reassemble the Hood, burners, Vaporizers, Grills and Plates.
Connect the base shelf to place.
Once done, stand the whole assembly upright. Fit rubber grommet.
For Barbecue set up, and Gas connections, refer to Barbecue instruction book.

5
Door Handle
To reverse a door direction
Cabinet handles should be mounted using the bottom and middle holes.
Doors are fully reversible, and can be Right or Left
hand opening.
To reverse a door, follow these steps:
1. Remove the door by lifting up off the hinge pin,
and taking out.
2. Remove the hinge blocks from the side panel,
turn upside down, and reattach to opposite
panel.
3. In the door, remove 2 hinge brackets and
reattach upside down, on other side of
opening.
4. Release the handle, turn upside down, and re-
attach.
5. Turn door upside down, and insert to place to
re-engage over hinges.
•Holes on the very end panels can be hidden using plugs ‘G’, ‘H’ and ‘I’ supplied.
•Each cabinet is fitted with 4 adjustable feet. The Outdoor Kitchen can be leveled by
adjusting these feet up or down, turning with the Allen key supplied from inside the
cabinet, through the holes in the corners.

6
Other Modules and accessories
If you have purchased other, optional modules to be part of your Outdoor Kitchen,
here are a few hints on assembly and function.
Cabinets
Position each cabinet to be added in its correct position, level it with the Outdoor
Kitchen, and then fasten to the near cabinet with the 4 screws included.
In position 1(below), 2 x screw, washers and nuts. In position 2 (below), 2 x special
screw – thread through both cabinets and tighten.
Sink Module
The sink module is supplied with a tap, and a drainage hose for sink
outlet. The tap is to be positioned in the hole in the bench top, and
tightened.
All water fittings and connections are the responsibility of the customer.
Drawer Module
To attach the drawer module to the rest of the Outdoor Kitchen, it will be
required to remove the drawer altogether, in order to gain access to the
holes through which the screws are inserted (see above).
To remove the drawer, simply pull out towards you completely.

7
Side Burner Module
The side burner is to be connected to the Gas supply.
BeefEater recommends positioning the side burner as close as possible to the
BBQ, and never using a rubber hose to connect longer than 1.5m.
Regulator is connected to entry ‘A’ (see below) in the Barbecue. Side Burner
connected to entry ‘B’ (see below) - remove cap and connect Side-Burner hose.
Ensure to conduct Leak-Test after making gas connections.
Refer also to Barbecue book P. 4 for Leak-Test procedure.
Ensure every place the hose is crossing the metal, is protected with a rubber
grommet. This is very important!
Connection to Side BurnerConnect to outlet ‘B’ in Barbecue
Shelves
If you wish to add shelves to the sides of your Outdoor Kitchen, they are
attached with 4 screws each from the inside of the end cabinets. No nuts
are required.
Regulator
Special castors to replace
the feet, and make your
Outdoor Kitchen mobile,
may be available from
your BeefEater stockiest,
or by calling BeefEater.

8
Warranty
Warranty terms and condition as listed in Barbecue Instructions book P. 11 apply to this Outdoor
Kitchen as well. All parts and workmanship of this Outdoor Kitchen are covered for a period of 1 year
from date of purchase.
Technical Information
Note: Do not modify this appliance or any of its parts. Any deviation from factory
settings could result in a safety hazard.
Side Burner manifold inlet thread is 3/8 SAE male flare fitting.
Input Energy (Side Burner): 15Mj.
Nozzle sizes: LPG – 1.05mm, NG – 1.7mm
For your records:
Model Number: __________________________________________________________
Date of Purchase: __________________________________________________________
Place where purchased:
__________________________________________________________
Serial Number:
__________________________________________________________
Spare Parts (Basic Cabinet):
1100_ODK_Inst_AU_V0
Images in this manual are for
illustrative purposes only.
Due to constant improvement,
BeefEater advises that changes to the
design, material, specifications and
product configuration may occur at
any time without notice.