Bell 882a200 User manual

BELLSYSTEM PRACTICES SECTION 503-200-110

AT&TCo Standard Issue 1, December 1975

882A200 TELEPHONE SETS

1. GENERAL mounting cord or the 225A adapter furnished with

each telephone set.

1.01 This section provides identification,installation,

and connection information for the 882A200 1.04 The 882A200 telephone set is available in

DESIGN LINE* telephone (Coquette)set (Fig. 1). white (-58) only.

*Trademark of AT&T Co. 2. IDENTIFICATION

1.02 Whenever this section is reissued,the reason 2.01 The 882A200 rotary dial equipped set is a

will be listed in this paragraph, new DESIGN LINE telephone set being

made available to the customer. The customer

Warning: Telephone apparatus or wiring buys the housing and handset from the telephone

shah not be installed in a location where company and the telephone company retains

minimum separation from other wiring ownership of the transmission and signaling

cannot be maintainedasspecit_edin Section components (Fig. 2 and 3).

460-300-149.

Fig. 1m882A200 DESIGN LINE Telephone Set

1.03 The customer's premises must be properly

wired with an appropriate connecting block

or jack in order to accept the D4BU-29 plug ended Fig. 2mCustomer-Owned Components

NOTICE

Not for use or disclosure outside the

Bell System except under written agreement

Printed in U.S.A. Page 1

SECTION 503-200- ! 10

2.02 Ordering Guide: 3.05 To gain access to the interior of the set

for wiring changes, refer to the appropriate

(a) The Coquette is a modular type white (-58) paragraphs in Part 4.

cradle phone equipped with a rotary dial

and may be ordered as follows: 3.06 Lineand RingerConnections:

•Set, Telephone,882A200 (1) For single line and two-party service, refer

to Table A.

This includes:

(2) For adjustments and ringer cutoff feature

(1) 882AS200 housing of the P1A ringer, refer to Section 501-259-101.

(2) 880DT-58 telephone unit4. REMOVAL OF TELEPHONECOMPANY-OWNED

COMPONENTS

Note: This includes all the components shown

in Fig. 3. 4.01 When it is desired to discontinue telephone

service of the 882A200 DESIGN LINE

2.03 These telephone sets are intended to be telephone set,proceed as follows:

used as single line or two-party desk sets

and are not recommended for use on four-party Note: Remove the telephone company-owned

eight-party service, components that can be easily removed. Refer

to Fig. 3 for identification of company-owned

components.

3. INSTALLATIONAND CONNECTIONS (1)Remove the four mounting screws from the

bottom of telephone set and remove the

3.01 These telephone sets are furnished from baseplate Fig. 2.

the factory fully assembled and wired for

bridged ringing. To connect the telephone set, (2) Remove components that are mounted to,

plug the mounting cord into a 625-type connecting or held by the baseplate.

block or if an existing 548A jack (or equivalent) is

provided use the 225A adapter furnished with each (3) Remove three dial mounting screws and

set. remove the rotary dial.

3.02 The internal connections for the 882A200 (4) Unscrew transmitter and receiver caps and

telephone set, for nonkey system use, are remove T1 transmitter and LB1 receive units.

shown in Fig. 4. (5) Replace baseplate.

3.03 Connections for 1A KTS do not require any

telephone set modifications and are wired 4.02 Follow local procedures for returning telephone

same as Fig. 4. company-owned components.

4.03 When it is desired to return a set to Western

3.04 Wiring modifications and connections for use Electric for repair,it should be packed using

with 1A1 or 1A2 KTS are shown in Table the D-180600 Kit of Parts which contains packing

B and Fig. 5. materials and instructions.

Page 2

ISS 1, SECTION 503-200-110

Fig. 3--Telephone Company-Owned Components

Page 3

SECTION 503-200-110

TABLE A

LINE AND RINGER CONNECTIONS (882A200 TELEPHONE SET)t

INDIVID. TIP PARTY

RING

WIRE OR LEAD COLOR OR

BRIDGED PARTY NO IDENT IDENTIFYING GROUND

GROUND 1000_, 2650_'_

Inside Wire at R R R R R R

Jack G G G G G G

Y Y Y Y Y Y

BK B B B B B

623P4 Line Jack R A A L1 F F

Assy G L1 L_A L2 L2

Y G G G G G

BK L2 L2 L2 **

Ringer R K K K K K

S-R * * * * L1

S * * * L1*

BK L1 G G G G

Line Switch Y A A A L2 L2

W F F F B B

• Insulated and stored.

tFor access to set wiring follow applicable steps in Part 4.

TABLE B

MODIFICATIONS FOR 1A1 or 1A2 KTS (882A200

TELEPHONE SET)*

NETWORK TERMINAL

LEAD COLOR REMOVE CONNECT

FROM TO

S A L2

Y A L2

Line BR C G

Switch G L1 A

W F C

623P4 Line G L1 F

Jack Assy

Ringer BK L1 F

* For access to telephone set wiringfollow applicable

steps in Part 4.

Page 4

ISS 1, SECTION 503-200-110

i I

Ib.

iiiimnlllllllmmllm

iL ¸ _ ._!ili

II--

iii iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_ii_

•-4 •

o"_ v

................................................................11111177iiiiii=iiiiii-iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii-iiiiiiiiiiiiiiiiiiii17111111.-17iiii......._......._._!_;.-...................---_,,

_" ._.

.............................................................................................................................................................,_:111--..-----1,_;i -T_P'__-T_+,---

-,ii -_ _ !4 1-4 -"

I I II

474-' ,,:

Page 5