bemodern Arteon Pryzm 10003SL Guide

1
Evento Timber Suites To Suit:
Arteon 10003SL & 12503SL Fires
Instructions for Installation
R1 DEC 2020 200805_1

2
Contents
Technical Specs 3
Contents of Fixings Box 4
Installation –Timber 5 –8
Maintenance 9
200805_1

3
Technical Specification
Fire Surround Logs Dimensions (mm)
A B C D E
ARTEON PRYZM
5D 1000 3SL
54” EVENTO
TIMBER FLOOR
STANDING
61270 271 842 320 1370
ARTEON PRYZM
5D 1250 3SL
64” EVENTO
TIMBER FLOOR
STANDING 81520 296 842 345 1620
Note: The Arteon Fire and Evento Surround are boxed separately- Light Assembly of the Evento Surround is
required- Please follow the steps detailed below.
Fire Visible Glass Area (mm)
F G H
ARTEON PRYZM
5D 1000 3SL 995 380 152
ARTEON PRYZM
5D 1250 3SL 1245 380 177
200805_1

4
What is in the box (s)
Box- 050237 (to suit the 1000 3SL) or Box 050253 (to suit the 12503SL)
200805_1
Please ensure all fixings are present before commencing installation. If anything is missing please call Customer
Services on 01914300901 or email us at [email protected].uk
8X 3.5 X 16.5 mm
Pozi Flange Head
2X
Metal Sides
Quantity Description Quantity Description
1ARTEON PRYZM 1000-3SL- Electric Fire Engine 1 Rear Bracket ( Not Required For This Installation)
6 Logs (Small Box Inside Fire) 1 Fire Remote Control & 2 x AAA Batteries (Large Box Inside Fire)
2 Bags of Crystals (Large Box Inside Fire) 4 Short Side Brackets (Large Box Inside Fire)
3 Bags of Pebbles (Large Box Inside Fire) 2 Long Side Brackets (Large Box Inside Fire)
2 Bags of Bark (Large Box Inside Fire) 1 Power Cable, Plug & IEC (1.8M) (Large Box Inside Fire)
2 Bags of Grey Slate (Large Box Inside Fire)
Box- 050164 –(1000-3SL)
Quantity Description Quantity Description
1ARTEON PRYZM 1250-3SL- Electric Fire Engine 1 Rear Bracket ( Not Required For This Installation)
8 Logs (Small Box Inside Fire) 1 Fire Remote Control & 2 x AAA Batteries (Large Box Inside Fire)
3 Bags of Crystals,(Large Box Inside Fire) 4 Short Side Brackets (Large Box Inside Fire)
3 Bags of Pebbles (Large Box Inside Fire) 2 Long Side Brackets (Large Box Inside Fire)
3 Bags of Bark (Large Box Inside Fire) 1 Power Cable, Plug & IEC (1.8M) (Large Box Inside Fire)
3 Bags of Grey Slate (Large Box Inside Fire)
Box- 050172–(1250-3SL)
Depending on the product size purchased:
Quantity Description
2 Metal Sides LH/RH- 601407
8 3.5 x 16.5mm POZI FLANGE HEAD screws bagged.
1 Downlight Instructions.
1 2M Downlight Mains Cable (Supplied to be used with a fused spur. i.e. A 3
Amp Switched Fused spur or 3 Amp 3 Pin Plug if using a double socket.
1 830mm Fly Lead- Required to connect the LED Lights to the Fire.
Quantity Description
1EVENTO- Assembled Top- with pre-installed Downlight Set & Sensor.
1EVENTO- Assembled Base- with pre-installed LED Light Set.
Also in Boxes 050237 & 050253, there is a smaller box ( Labelled A) containing
the following: 1X Downlight
Mains Cable
1X 830mm
Fly Lead

5
Installation –Timber
Before the surround can be installed, consideration will need to be given routing the power supply to the fire. This
will affect the stages of the installation process. We advise a qualified electrician conduct any electrical parts of the
installation.
Note: A double socket is required or a single socket and a 3 Amp switched fused spur for the operation of the
Fire and the preinstalled Downlights.
Unpack your new suite- DO NOT dispose of the packaging until you have checked and made sure all the parts and
fixings listed on Page 4 are present. Tip: To help avoid damage of the assembled parts place them on the surplus
packaging, whilst they are waiting to be installed.
Note: This installation guide is detailed for both 54” and 64” sized surrounds so please familiarise yourself with
the model you have purchased before beginning installation.
Note: The surround and fire are a two adult person lift. A second person will be required to lift and support
the surround and fire during installation.
200805_1
Once the Fire has been prepared, lift the unpacked
Assembled Base into position.
Remove any obstructions, i.e. mark and cut to shape
or remove any skirting to allow the Assembled Base to
butt up flush to the wall.
See Diagram 2.
Note: The Assembled Base is a two adult person lift.
Diagram 1
Position the Assembled Base away from the wall,
leaving enough space to the rear to allow the Fire and
Metal Sides to be installed in the following steps.
See Diagram 3.
Diagram 2
1.
2.
Preparing the fire- See the separate Fire Instructions.
Locate the box containing the Fire-050164 or 050172
depending on the version purchased and locate the
Fire Instructions.
Please refer to the Pages 8-9, in the Fire Instructions
and follow the steps to remove the Glass and Rear
Bracket and the internal cardboard boxes.
Please refer to Page 10- Diagram 11 in the Fire
Instructions to prepare the Fire for a 3 Sided
installation.
Diagram 3
3.

6
Installation –Timber continued
200805_1
Ensure the Fire is positioned centrally in the cut out of
the Assembled Base and that the Fire is pushed up tight
against the front of the opening.
See Diagram 5.
Diagram 5
Locate the 2 x Metal Sides , these are packaged in the
small cardboard box, (Box A- found inside the surround
box), along with the 8 x 3.5 X 16mm Pozi Flange Head
Screws, required for fixing.
Note: Remove any protective film before installing.
Position the 2 x Metal Sides with the tab at the top.
Line up the holes in the Metal Sides with the pre-drilled
holes on the Assembled Base .
See Diagram 6.
Diagram 6
Once aligned, fix the Metal Sides to the Assembled Base
using 4 x 3.5 X 16mm Pozi Flange Head Screws
provided.
See Diagram 7.
Tip: If the holes do not align go back to step 4 and
ensure the Fire has been positioned centrally in the
opening of the Assembled Base.
4.
5.
6.
Note: Ensure the glass and cardboard boxes inside
the fire have been removed before proceeding
further, this will reduce the handling weight.
Lift the Fire into the cut out in the Assembled Base,
ensuring the Fire is sitting on the two central supports.
See Diagram 4.
Note: The fire is a two adult person lift.
Diagram 4
Diagram 7
7.

7
Installation –Timber continued
10.
Diagram 10
11.
Diagram 11
Lift the partially assembled surround against the wall.
Ensuring the Metal Sides are plumb - mark the location
of the fixing points on the wall behind.
See Diagram 9.
Remove the partially assembled surround from the wall
and drill and plug the fixing points.
Note: Plugs and fixings are not supplied- See Important
Note on Page 9.
Note: This is a two adult person lift.
9.
Diagram 9
200805_1
Note: Once the partially assembled surround has been
secured to the wall, connect the pre-installed Downlights
to the mains cable, checking that the lights and sensor are
working correctly.
If there are any problems please call Customer Services on
01914300901 or email us at
[e-mail]
Finally return the partially assembled surround against the
wall.
Note: Great care must be taken to avoid crushing or
damaging the cables on installation.
Note: Ensure the Downlight mains cable (white cable) is
routed in a way that it can be connected to the pre-
installed Downlights in the Assembled Top when it is
positioned in a later procedure. See Diagram 11.
Once routed correctly, proceed with fixing the surround to
the wall. See Diagram 10.
Diagram 8
(Please refer to Page 11 in the Fire Instructions, before
proceeding further and ensure the Power Cable and LED
Light Set are connected to the relevant connection
ports.
See Diagram 8.
Note: At this stage also wire in or plug in the mains
cable for the Downlights. (The cable found in the
smaller cardboard box that comes with the surround.)
8.

8
Installation –Timber continued
14.
Diagram 14
13.
Diagram 13
200805_1
Line up the holes in the Metal Sides with the pre-drilled
holes on the Assembled Top.
Once the holes are aligned, fix to the Assembled Top
using 4 No. 3.5 X16mm Pozi Flange Head Screws
provided.
See Diagram 14.
Note: DO NOT seal around the edges of the top
between the wall- access to the downlights and
sensor may be required in the event of failure.
Once the installation is complete, please refer to Page 15
in the Fire Instructions (with the Fire), for advice on how
to dress the Fuel Bed and position the Logs.
Once the Logs and Fuel Bed have been dressed
remember to replace the Glass- securing with the
previously removed Screws. Please refer to Page 16 in
the Fire Instructions.
For the Fire User Instructions, please refer to Pages 17-
23, in the Fire Instructions.
12.
Diagram 12
Ensure the Assembled Top is centralized on the Metal
Sides, before fixing in position.
There should be approx. 21mm overhang each side.
See Diagram 13
15.
Diagram 15
Lift the Assembled Top into position.
Note: The Assembled Top is a two adult person lift.
Note: Great care must be taken to avoid crushing or
damaging the Downlight cables during installation.
See Diagram 12.

9
Maintenance
WARNING: Before any maintenance or whilst cleaning the exterior of the fireplace, the unit should
be disconnected from the power supply until it has cooled down.
Cleaning the Furniture
To maintain the appearance of your new suite we recommend that it dusted using a lint free cloth.
NEVER use any form of abrasive or DAMP cloth.
Cleaning the Fire and the Metal Sides
Cleaning or polishing products is not recommended. Fingerprints or other marks on the front glass
panel and metal sides can be removed by using a piece of soft, damp, lint-free cloth with a good quality
household glass cleaner. The front glass panel should always be completely dried with a clean, lint-free
cloth or paper towel.
CAUTION: Abrasive cleaners should not be used on the glass panel. Liquids should not be sprayed
directly onto any surface of the unit.
Troubleshooting
Should you have any queries regarding this product please contact Customer Services on
01914300901 or email us at [e-mail]
Recycling
All cardboard packaging is recyclable.
200805_1
IMPORTANT NOTE:
Wall fixings (i.e. screws/wall plugs etc.) are not supplied as these are crucially dependent upon the type of wall and
surface the surround is going to be fixed too.
The installer is therefore responsible for ensuring that suitable fittings are used as well as individual fitting situations
and environments. All mechanical fixings, for holding the surround in position, must be secured to a solid wall or
structure.