Bender RFID105-L1 User manual

Manual EN
RFID105-L1
For use in combination with charge controllers used in electric vehicle charging
stations, wall boxes and street light charging points
Illustration similar
RFID105-L1_D00453_02_M / 08.2023

Table of contents
Table of contents
1General information...........................................................................................3
1.1 How to use the manual.................................................................................................................................
1.2 Indication of important instructions and information.......................................................................
1. Signs and symbols...........................................................................................................................................
1.4 Service and Support.......................................................................................................................................
1.5 Training courses and seminars...................................................................................................................
1.6 Delivery conditions......................................................................................................................................... 4
1.7 Inspection, transport and storage.............................................................................................................4
1.8 Warranty and liability.....................................................................................................................................4
1.9 Disposal of Bender devices..........................................................................................................................4
1.10 Safety.................................................................................................................................................................... 5
2Device-specific safety instr ctions................................................................... 6
3F nction...............................................................................................................7
.1 Intended use......................................................................................................................................................7
.2 Functional description...................................................................................................................................7
. LED status........................................................................................................................................................... 7
.4 Operation............................................................................................................................................................ 8
.5 RJ45 connector pin assignment.................................................................................................................8
4Dimensions and mo nting................................................................................ 9
5Technical Data.................................................................................................. 10
5.1 Tabular data.................................................................................................................................................... 10
5.2 Standards and approvals............................................................................................................................11
5. Declarations of Conformity....................................................................................................................... 11
5.4 Ordering information...................................................................................................................................11
2 RFID105-L1_D0045 _02_M / 08.202

RFID105-L1
1 General information
1.1 How to se the man al
ADVICE
This manual is intended for qualified personnel working in electrical engineering and electronics!
Part of the device documentation in addition to this manual is the enclosed supplement "Safety
instructions for Bender products".
ADVICE
Read the operating manual before mounting, connecting and commissioning the device. Keep the
manual within easy reach for future reference.
1.2 Indication of important instr ctions and information
DANGER
Indicates a high risk of danger that will result in death or serious injury if not avoided.
WARNING
Indicates a medium risk of danger that can lead to death or serious injury if not avoided.
CAUTION
Indicates a low-level risk that can result in minor or moderate injury or damage to property if not
avoided.
Information can help to optimise the use of the product.
1.3 Signs and symbols
Disposal Protect from moisture Protect from dust
Temperature range Recycling RoHS directives
1.4 Service and S pport
Information and contact details about customer service, repair service or field service for Bender devices are
available on the following website: Fast assistance | Bender GmbH & Co. KG.
1.5 Training co rses and seminars
Regular face-to-face or online seminars for customers and other interested parties:
www.bender.de > know-how > seminars.
RFID105-L1_D0045 _02_M / 08.202

General information
1.6 Delivery conditions
The conditions of sale and delivery set out by Bender GmbH & Co. KG apply. These can be obtained in printed
or electronic format.
The following applies to software products:
Die Elektroindustrie
‘Software clause in respect of the licensing of standard software as part of deliveries,
modifications and changes to general delivery conditions for products and services in the
electrical industry’
1.7 Inspection, transport and storage
Check the shipping and device packaging for transport damage and scope of delivery. In the event of
complaints, the company must be notified immediately, see "www.bender.de > service & support.".
The following must be observed when storing the devices:
1.8 Warranty and liability
Warranty and liability claims for personal injury and property damage are excluded in the case of:
•Improper use of the device.
•Incorrect mounting, commissioning, operation and maintenance of the device.
•Failure to observe the instructions in this operating manual regarding transport, commissioning, operation
and maintenance of the device.
•Unauthorised changes to the device made by parties other than the manufacturer.
•Non-observance of technical data.
•Repairs carried out incorrectly.
•The use of accessories or spare parts that are not provided, approved or recommended by the
manufacturer.
•Catastrophes caused by external influences and force majeure.
•Mounting and installation with device combinations not approved or recommended by the manufacturer.
This operating manual and the enclosed safety instructions must be observed by all persons working with the
device. Furthermore, the rules and regulations that apply for accident prevention at the place of use must be
observed.
1.9 Disposal of Bender devices
Abide by the national regulations and laws governing the disposal of this device.
For more information on the disposal of Bender devices, refer to
www.bender.de > service & support.
4 RFID105-L1_D0045 _02_M / 08.202

RFID105-L1
1.10 Safety
If the device is used outside the Federal Republic of Germany, the applicable local standards and regulations
must be complied with. In Europe, the European standard EN 50110 applies.
DANGER Risk of fatal injury due to electric shock!
Touching live parts of the system carries the risk of:
•Risk of electrocution due to electric shock
•Damage to the electrical installation
•Destruction of the device
Before installing the device and before working on its connections, make sure that the installation
has been de-energised. The rules for working on electrical systems must be observed.
RFID105-L1_D0045 _02_M / 08.202 5

Device-specific safety instructions
2 Device-specific safety instr ctions
ADVICE
The RFID module complies with the relevant harmonized standards to ensure that the requirements
of the Radio Equipment Directive (see the chapter “Declarations of Conformity”) are met. It is the
responsibility of the distributor of the complete system to ensure conformity with this and any
additional legal requirements.
WARNING Very bright RGB LEDs
Vision impairment!
Care must be taken to avoid looking directly into the RGB LEDs.
WARNING Electromagnetic wa es and fields
Health hazards!
The device emits electromagnetic waves and fields for radio communication when in operation. Care
must be taken to avoid a continuous proximity of less than 20cm to body parts.
6 RFID105-L1_D0045 _02_M / 08.202

RFID105-L1
3 F nction
3.1 Intended se
The RFID module must only be used in combination with charge controllers from Bender GmbH & Co. KG. The
module is a separate PCB which facilitates user interaction with the charging system.
Any other use or a use that goes beyond this constitutes improper use.
This document is intended to be used together ith the operating manuals for the charge controllers used,
hich can be do nloaded here: https:// .bender.de/en/service-support/do nload-area/
3.2 F nctional description
The RFID module is used in combination with the charge controller within a charging system to authorize
charging transactions.
The RFID frequency is 1 .56 MHz. The PN5 2 Near Field Communication (NFC) controller used for contactless
communication supports nearly all RFID/NFC communication media operating on this frequency. Currently
only passive tags with a UID are read. Further functionality is possible upon request.
3.3 LED stat s
Illustration similar
LED Status
1Lights up in parallel
to 3
•Authorization process is running
•The signalisation of the current authorisation by circular light patterns
continuously lighting •Charging system is free
•No vehicle is connected
2
slo flashing •Charging system is free
•Vehicle is connected
RFID105-L1_D0045 _02_M / 08.202 7

Function
LED Status
continuously lighting •Charging system is reserved
•No vehicle is connected
slo flashing •Charging system is reserved
•Vehicle is connected
3
fast flashing •Charging system is exchanging data ith the backend
•Waiting for an authorisation
slo flashing •Charging has been authorised
•Vehicle is charging
4fast flashing •Charging has been authorised
•Vehicle is not yet connected or has just been disconnected from the charging
system
2, 3, 4* fast flashing •Authorization has been rejected.
•Fault in the charging system.
•The backend is not available
* Measures for fault correction can be consulted in the manual of the charge controller.
3.4 Operation
The charging is initiated by holding a valid RFID card close to the reader on the RFID module. The status of the
LEDs changes. Charging can be terminated when the RFID card is again held in front of the charging system.
3.5 RJ45 connector pin assignment
Pin number Description
1 I2C (not used for the RFID functionality)
2 I2C (not used for the RFID functionality)
3 GND
4 RX PN532
5 TX PN532
6 3.3 V
7 5 V (not used for the RFID functionality)
8 GND
8 RFID105-L1_D0045 _02_M / 08.202

RFID105-L1
4 Dimensions and mo nting
Dimensions
Dimensions in mm; Tolerance acc. to ISO 2768-m
Red markings: possible attachment points
Mo nting
The RFID module is installed under a semi-transparent part of the charging system housing. It must be placed
at a distance of at least 20 mm from any significant metal surface or metal parts to ensure optimum RFID
reading performance.
The module is connected to the charge controller, which is the main component of the charging system, using
a standard RJ45 cable.
CAUTION Electrostatic discharge!
Damage to device
Electrostatic discharge (ESD) can damage electronic components. Precautions for handling
electrostatically sensitive components in accordance with DIN EN 61 40-5-1 and DIN IEC/TR
61 40-5-2 must be observed.
RFID105-L1_D0045 _02_M / 08.202 9

Technical Data
5 Technical Data
5.1 Tab lar data
Ins lation coordination acc. to IEC 60664-1/ IEC 60664-3
Rated voltage 12.5 V
Pollution degree 2
Rated impulse ithstand voltage 800 V
Rated insulation voltage 12.5 V
Altitude ≤ 2000 m AMSL
Rated voltage/rated c rrent
Rated voltage DC 3.3 / 5 V
Rated voltage tolerance ± 5 %
Rated current 140 / 64 mA
Freq ency / Transmitting power
Radio frequency 13.56 MHz
Max. transmitting po er* 42 dBμA/m
* at a distance of 10m
Environment / EMC
Operating temperature -30 … +70 °C
Climatic conditions acc. to IEC 60721:
Stationary use (IEC 60721-3-3) 3K23 (except condensation, ater and formation of ice)
Transport (IEC 60721-3-2) 2K11
Long-term storage (IEC 60721-3-1) 1K21
echanical conditions acc. to IEC 60721:
Stationary use (IEC 60721-3-3) 3M11
Transport (IEC 60721-3-2) 2M4
Long-term storage (IEC 60721-3-1) 1M12
Connection
Charge controller connection RJ45 cable*
Maximum cable length < 2 m
* Type: CAT 5e Class D, RF/UTP, twisted pair patch cable, AWG 26/7
10 RFID105-L1_D0045 _02_M / 08.202

RFID105-L1
Other
Protection class IP00
Max. RFID reading distance 100 mm
Weight 25 g
5.2 Standards and approvals
The RFID module has been developed in compliance with:
•ISO 1444 A/MIFARE
•For additional standards, see the chapter “Declarations of Conformity”
R-NZ
Use in the EU and other co ntries
The conformity ith the relevant EU directives permits operation of the device exclusively in countries of
the European Economic Area.
The conformity ith the relevant UKCA directives permits operation of the device exclusively in the United
Kingdom.
The device is certified for operation in Australia by the Australian Communications and Media Authority.
The device is certified for operation in Ne Zealand by the Radio Spectrum Management.
5.3 Declarations of Conformity
EU Declaration of Conformity
Hereby, Bender GmbH & Co. KG declares that the device covered by the Radio Directive complies with
Directive 2014/5 /EU. The full text of the EU Declaration of Conformity is available at the following Internet
address:
https://www.bender.de/fileadmin/content/Products/CE/CEKO_RFID10x.pdf
UK Declaration of Conformity
Hereby, Bender GmbH & Co. KG declares that this device is in compliance with Radio Equipment Regulations
2017 (S.I. 2017/1206). The full text of the UK declaration of conformity is available at the following internet
address:
https://www.bender.de/fileadmin/content/Products/UKCA/UKCA_RFID10x.pdf
5.4 Ordering information
Type Part number anual number
RFID105-L1 B94060105 D00453
RFID105-L1_D0045 _02_M / 08.202 11

Bender GmbH & Co. KG
Londorfer Straße 65
5 05 Grünberg
Germany
Alle Rechte vorbehalten.
Nachdruck und Vervielfältigung nur mit
Genehmigung des Herausgebers.
Tel.: [phone]
[email protected]
www.bender.de
All rights reserved.
Reprinting and duplicating only with
permission of the publisher.
© Bender GmbH & Co. KG, Germany
Subject to change! The specified
standards take into account the edition
valid until 08.202 unless otherwise
indicated.