Bender RFID114 User manual

Manual
EN
RFID114_D00328_00_M_XXEN/04.2018
For use in combination with charge controllers used in
electric vehicle charging stations, wall boxes or street
light charging points
RFID114

Bender GmbH & Co. KG
P.O. Box 1161 • 35301 Grünberg • Germany
Londorfer Str. 65 • 35305 Grünberg • Germany
Tel.: [phone] • Fax: [phone]
E-mail: [e-mail] • www.bender.de
© Bender GmbH & Co. KG
All rights reserved.
Reprinting only with permission of the publisher.
Subject to change!
Photos: Bender archives

Table of Contents
3
RFID114_D00328_00_M_XXEN/04.2018
1. Important information .................................................................................... 5
1.1 How to use this manual ................................................................................. 5
1.2 Technical support: service and support ................................................... 5
1.3 Delivery conditions .......................................................................................... 6
1.4 Inspection, transport and storage .............................................................. 6
1.5 Disposal ............................................................................................................... 6
1.6 Intended use ...................................................................................................... 6
2. RFID module ..................................................................................................... 8
2.1 Dimensions for mounting ............................................................................. 9
2.2 Operation ......................................................................................................... 10
3. Technical data ................................................................................................. 11
3.1 Tabular data .................................................................................................... 11
3.2 Standards, approvals, certifications ........................................................ 13
3.3 Ordering information .................................................................................. 13
3.4 Declaration of conformity .......................................................................... 14

Table of Contents
4RFID114_D00328_00_M_XXEN/04.2018

5
RFID114_D00328_00_M_XXEN/04.2018
1. Important information
1.1 How to use this manual
Always keep this manual within easy reach for future reference.
1.2 Technical support: service and support
Technical support by phone or e-mail for all Bender products
 Questions concerning specific customer applications
 Commissioning
 Troubleshooting
Telephone: [phone]*
Fax: [phone]
In Germany only: 0700BenderHelp (telephone and fax)
E-mail: [email protected]
*Available from 7.00 a.m. to 8.00 p.m. 365 days a year (CET/UTC +1)
1.3 Delivery conditions
Bender sale and delivery conditions apply. These can be obtained from
Bender in printed or electronic format.
This manual is intended for qualified personnel working in
electrical engineering and electronics!
This symbol denotes information intended to assist the user
in making optimum use of the product.

Important information
6RFID114_D00328_00_M_XXEN/04.2018
1.4 Inspection, transport and storage
Inspect the dispatch and equipment packaging for damage, and compare the
contents of the package with the delivery documents. In the event of damage
in transit, please contact Bender immediately. The devices must only be
stored in areas where they are protected from dust, damp, and spray and drip-
ping water, and in which the specified storage temperatures can be ensured.
1.5 Disposal
Abide by the national regulations and laws governing the disposal of this de-
vice. Ask your supplier if you are not sure how to dispose of the old equip-
ment.
For more information on the disposal of Bender devices, refer to our
homepage at www.bender.de -> Service & support.
1.6 Intended use
This manual provides a description of an RFID module which may only be
used in combination with Bender charge controllers. The charge controller is
designed for use in electric vehicle (EV) charging stations, wall boxes and
street light charging points. This document should be used together with the
charge controller operating manual(s), which can be downloaded from:
www.bender.de/en/service-support/downloads
The RFID module is a separate PCB which facilitates user interaction with the
charging system and is designed in accordance with the ISO14443A/MIFARE
standard. It can be connected to the charge controller via the provided RJ45
cable.
Charging is initiated by holding a valid RFID card, which is registered in a back-
end system, close to the antenna of the RFID module. In offline operation, the
charge controller can optionally allow charging without authorization or it
can authorize users based on RFID and a local white list of authorized RFID
cards.

7
RFID114_D00328_00_M_XXEN/04.2018
2. RFID module
The RFID module shown below contains an antenna.
All dimensions in mm
It is a PCB that should be placed under a metal-free charging system enclo-
sure.
The RFID module must be mounted at a distance of at least
20 mm from any significant metal surface or metal parts to
ensure an optimum reading performance of the RFID
module.
CAUTION
Electrostatic discharge (ESD) may cause damage to electron-
ic components. Observe the precautions for handling elec-
trostatically sensitive components in accordance with DIN
EN 61340-5-1 and DIN EN 61340-5-2.
102.88
57.09
Note: Tolerance acc. to ISO 2768 - m

RFID module
8RFID114_D00328_00_M_XXEN/04.2018
The RFID frequency is 13.56 MHz. Bender uses the PN532 Near Field Com-
munication (NFC) controller for contactless communication, which supports
virtually all RFID/NFC communication means on this frequency. Currently only
passive tags with a UID are read. Further functionality is possible upon re-
quest.
2.1 Dimensions for mounting
All dimensions in mm
The provided RJ45 cable has a length of 50 cm.
However, the cable must not be longer than 3 m and must
comply with the CAT5 standard or higher.
2.68
2.7
2.7
46.70
3
.
1
2.7 7.69
97.5
7.69
2
.
8
Note: Tolerance acc. to ISO 2768 - m

RFID module
9
RFID114_D00328_00_M_XXEN/04.2018
2.2 Operation
The charging process is initiated by holding a valid RFID card close to the an-
tenna of the RFID module.
The charging process can be finished by holding the RFID card close to the
RFID module again.

Technical data
10 RFID114_D00328_00_M_XXEN/04.2018
3. Technical data
3.1 Tabular data
Insulation coordination acc. to IEC 60664-1/IEC 60664-3
Rated voltage .........................................................................................................................................................12.5 V
Overvoltage category.....................................................................................................................................................III
Pollution degree..............................................................................................................................................................3
Rated impulse withstand voltage...........................................................................................................................800 V
Rated insulation voltage........................................................................................................................................12.5 V
Altitude..................................................................................................................................................≤ 2000 m AMSL
Nominal voltage/nominal current
Nominal voltage..................................................................................................................................................DC 3.3 V
Nominal voltage tolerance .................................................................................................................................... ±5 %
Nominal current.....................................................................................................................................................80 mA
Frequency
Radio frequency ..............................................................................................................................................13.56 MHz
Environment
Operating temperature............................................................................................................................ -30…+70 °C
Climatic conditions acc. to IEC 60721:
Stationary use (IEC 60721-3-3)..............................................3K5 (except condensation, water and formation of ice)
Transport (IEC 60721-3-2)........................................................................................................................................ 2K2
Long-term storage (IEC 60721-3-1)......................................................................................................................... 1K2