Bender RFID117-L1 User manual

Manual ENRFID117-L1_D00422_00_M / 08.2020
RFID117-L1
For use in combination with charge controllers used in
electric vehicle charging stations, wall boxes and street
light charging points

2 RFID117-L1_D00422_00_M / 08.2020
Service and support for Bender-products
First-level support
Technical support
Carl-Benz-Strasse 8 • 35305 Grünberg • Germany
Telephone: [phone]
0700BenderHelp * / Fax: [phone]
E-mail: [e-mail]
365 days from 7.00 a.m. to 8.00 p.m. (MEZ/UTC +1)
* Landline German Telekom:
Mon-Fri from 9.00 a.m. to 6 p.m.: 6.3 cents/30 sec.;
remaining time: 6.3 cents/min.
Mobile phone: higher, depending on mobile phone tariff
Repair service
Repair, calibration and replacement service
Londorfer Strasse 65 • 35305 Grünberg • Germany
Telephone: [phone] (technical issues) or
[phone], -785 (commercial issues)
Fax: [phone]
E-mail: [email protected]
Field service
On-site service
Telephone: [phone], -762 (technical issues) or [phone] (commercial issues)
Fax: [phone]
E-mail: fi[e-mail]
Mon-Thu 7.00 a.m. to 4.00 p.m., Fri 7.00 a.m. to 1 p.m. (MEZ/UTC +1)

RFID117-L1_D00422_00_M / 08.2020 3
RFID117-L1
Table of contents
1 General instructions ............................................................................................... 5
1.1 How to use this manual.......................................................................................................................... 5
1.2 Indication of important instructions and information ............................................................... 5
1.2.1 Signs and symbols .................................................................................................................................... 5
1.3 Training courses and seminars............................................................................................................. 5
1.4 Delivery conditions................................................................................................................................... 5
1.5 Inspection, transport and storage ...................................................................................................... 6
1.6 Warranty and liability............................................................................................................................... 6
1.7 Disposal of Bender devices.................................................................................................................... 6
1.8 Safety ............................................................................................................................................................. 6
2 RFID module.............................................................................................................. 7
2.1 Intended use............................................................................................................................................... 7
2.2 Dimensions and mounting.................................................................................................................... 7
2.2.1 Dimensions for mounting...................................................................................................................... 7
2.3 LED status..................................................................................................................................................... 8
2.4 Operation ..................................................................................................................................................... 9
2.4.1 RJ45 connector pin assignment .......................................................................................................... 9
3 Technical Data ........................................................................................................10
3.1 Standards, approvals, certifications .................................................................................................10
3.2 Ordering information ............................................................................................................................10
3.3 Declaration of conformity....................................................................................................................11

4 RFID117-L1_D00422_00_M / 08.2020

RFID117-L1_D00422_00_M / 08.2020 5
RFID117-L1
1 General instructions
1.1 How to use this manual
This manual is intended for qualified personnel working in electrical engineering and electronics! Part of
the device documentation, in addition to this manual, is the enclosed “Safety instructions for Bender
products”.
Read the manual before installing, connecting and commissioning the device. Always keep the manual
within easy reach for future reference.
1.2 Indication of important instructions and information
I Danger! Indicates a high risk of danger that will result in death or serious injury if not avoided.
I Warning! Indicates a medium risk of danger that can lead to death or serious injury, if not avoided.
I Caution! Indicates a low-level risk that can result in minor or moderate injury or damage to property if not
avoided.
i
Information can help to optimise the use of the product.
1.2.1 Signs and symbols
Disposal Temperature range protect from dust
protect from wetness Recycling RoHS
guidelines
1.3 Training courses and seminars
www.bender.de > Know-how-> Seminars.
1.4 Delivery conditions
The conditions of sale and delivery set out by Bender apply. These can be obtained from Bender in printed or elec-
tronic format.
The following applies to software products:
“Software clause in respect of the licensing of standard software as part of de-
liveries, modifications and changes to general delivery conditions for products
and services in the electrical industry.”
Die Elektroindustrie

6 RFID117-L1_D00422_00_M / 08.2020
General instructions
1.5 Inspection, transport and storage
Check the shipping and device packaging for transport damage and scope of delivery. The following must be ob-
served when storing the devices:
1.6 Warranty and liability
Warranty and liability claims in the event of injury to persons or damage to property are excluded in case of:
• Improper use of the device.
• Incorrect mounting, commissioning, operation and maintenance of the device.
• Failure to observe the instructions in this operating manual regarding transport, commissioning, opera-
tion and maintenance of the device.
• Unauthorised changes to the device made by parties other than the manufacturer.
• Non-observance of technical data.
• Repairs carried out incorrectly.
• Use of accessories and spare parts not recommended by Bender.
• Catastrophes caused by external influences and force majeure.
• Mounting and installation with device combinations not recommended by the manufacturer.
This operating manual and the enclosed safety instructions must be observed by all persons working with the de-
vice. Furthermore, the rules and regulations that apply for accident prevention at the place of use must be ob-
served.
1.7 Disposal of Bender devices
Abide by the national regulations and laws governing the disposal of this device.
For more information on the disposal of Bender devices, refer to
www.bender.de -> Service & support.
1.8 Safety
If the device is used outside the Federal Republic of Germany, the applicable local standards and regulations must
be complied with. In Europe, the European standard EN 50110 applies.
I Danger! Risk of electrocution due to electric shock!
Touching live parts of the system carries the risk of:
• A fatal electric shock
• Damage to the electrical installation
• Destruction of the device
Before installing and connecting the device, make sure that the installation has been de-energised. The rules for
working on electrical systems must be observed.

RFID117-L1_D00422_00_M / 08.2020 7
RFID117-L1
2 RFID module
2.1 Intended use
This manual provides a description of an RFID module, which can only be used in combination with Bender charge
controllers. The charge controller is designed for use in electric vehicle (EV) charging stations, wall boxes and
street light charging points. This document should be used together with the charge controller operating manu-
al(s), which can be downloaded from: www.bender.de/manuals.
The RFID module is a separate PCB which facilitates user interaction with the charging system and is designed ac-
cording to ISO14443A/MIFARE. It can be connected to the charge controller, the main component of a charging
system, using a standard RJ45 cable.
2.2 Dimensions and mounting
2.2.1 Dimensions for mounting
Note: Tolerance acc. to ISO 2768-m; DImensions in mm
The RFID module is integrated solely in conjunction with Bender charge controllers under professional installation.
In most cases these charge controllers implement the functionality of an electric vehicle charging system in which
the RFID module is used to authorize charging transactions.
The module is placed under a semi-transparent part of the charging system housing. It must be placed at a distan-
ce of at least 20 mm from any significant metal surface or metal parts to ensure optimum RFID reading perfor-
mance.
The RFID frequency is 13.56 MHz. Bender uses the PN532 Near Field Communication (NFC) controller for contact-
less communication, which supports virtually all RFID/NFC communication means on this frequency. Currently
only passive tags with a UID are read. Further functionality is possible upon request.
2.7
2.7
46.7
102.9
7.7
97.5
57.1
= Ø 3.1

8 RFID117-L1_D00422_00_M / 08.2020
RFID module
I Caution! Electrostatic discharge (ESD) can damage electronic components. Observe the precautions for
handling electrostatically sensitive components in accordance with DIN EN 61340-5-1 and DIN EN 61340-5-2.
i
The RJ45 cable delivered has a length of 50 cm. Ccable lengths max. < 3 m.
2.3 LED status
LED Status
1 lighting parallel to 3 • Authorization process is running
• The signalisation of the current authorisation by circular light patterns
2
continuously lighting • Charging system is free
• No vehicle is connected
slow ashing • Charging system is free
• Vehicle is connected
3
continuously lighting • Charging system is reserved
• No vehicle is connected
slow ashing • Charging system is reserved
• Vehicle is connected
fast ashing • Charging system is exchanging data with the backend
• Waiting for an authorisation
4
slow ashing • Charging has been authorised
• Vehicle is charging
fast ashing
• Charging has been authorised
• Vehicle is not yet connected or has just been disconnected from the
charging system
2,3,4* fast ashing
• Authorization has been rejected.
• Fault in the charging system.
• The backend is not available
i
*Measures for fault correction can be consulted in the manual of the charge controller.
1
4
2
3

RFID117-L1_D00422_00_M / 08.2020 9
RFID117-L1
2.4 Operation
The charging is initiated by holding a valid RFID card close to the reader on the RFID module.
Charging can be terminated when the RFID card is again held in front of the charging system.
2.4.1 RJ45 connector pin assignment
Pin number Describtion
1 I2C (not used for the RFID functionality)
2 I2C (not used for the RFID functionality)
3 GND
4 RX PN532
5 TX PN532
63,3 V
7 5 V (not used for the RFID functionality)
8 GND

10 RFID117-L1_D00422_00_M / 08.2020
Technical Data
3 Technical Data
Insulation coordination acc. to IEC 60664-1/
IEC 60664-3
Rated voltage ........................................................................ 12.5 V
Overvoltage category.....................................................................III
Pollution degree ............................................................................2
Rated impulse withstand voltage .......................................... 800 V
Rated insulation voltage........................................................ 12.5 V
Altitude .................................................................≤ 2,000 m AMSL
Rated voltage/rated current
Rated voltage.................................................................. DC 3.3/5 V
Rated voltage tolerance..........................................................± 5 %
Rated current ................................................................. 140/64 mA
Frequency
Radio frequency ..............................................................13.56 MHz
Environment/EMC
Operating temperature...............................................-30…+70 °C
Climatic conditions acc. to IEC 60721:
Stationary use (IEC 60721-3-3).....3K5 (except condensation, water
and formation of ice)
Transport (IEC 60721-3-2) ........................................................2K11
Long-term storage (IEC 60721-3-1)..........................................1K21
Mechanical conditions acc. toIEC 60721:
Stationary use (IEC 60721-3-3)................................................3M11
Transport (IEC 60721-3-2) .........................................................2M4
Long-term storage (IEC 60721-3-1)........................................1M12
Connection
Connection to charge controller..................................via RJ45 cable
Maximum cable length...........................................................< 3 m
Other
Protection class .........................................................................IP00
Maximum read distance. .....................................................100 mm
Weight ......................................................................................25 g
3.1 Standards, approvals, certifications
The RFID has been developed in compliance with:
• ISO 14443A/MIFARE
• EN 50364: 2010
• EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 + AC: 2011 + A2: 2013
• EN 61851-1: 2011
• EN 61851-22: 2002
• EN 50581: 2012
• ETSI EN 301 489-1 V2.1.1: 2017
• ETSI EN 301 489-3 V2.1.1 Final Draft: 2017
• EN 300 330 V2.1.1: 2017
3.2 Ordering information
Type Art.-No.
RFID117-L1 (RJ45 cable (length 500 mm) included) B 94060117

RFID117-L1_D00422_00_M / 08.2020 11
RFID117-L1
3.3 Declaration of conformity
Bender GmbH & Co. KG
Postfach 1161 • 35301 Grünberg/Germany
Londorfer Straße 65 • 35305 Grünberg/Germany
Phone: [phone] • Fax: [phone]
E-Mail: [e-mail] • www.bender.de
EU - K o n f o r m i t ä t s e r k l ä r u n g
E U - D e c l a r a t i o n o f C o n f o r m i t y
Hersteller:
Manufacturer:
Bender GmbH & Co. KG
erklärt in alleiniger Verantwortung, dass das Produkt
declare under our sole responsibility that the product
Produktbezeichnung:
Product name:
RFID11x (siehe Anlage)
RFID11x (see annex)
auf das sich diese Erklärung bezieht, mit den Vorschriften
folgender Europäischen Richtlinien übereinstimmt.
to which this declaration relates, is in conformity with the
following European directives.
Grünberg, den 18.08.2020
Anmerkung:
Remark:
Die Anlagen sind Bestandteil dieser EU-Konformitätserklärung.
*Evtl. Normen Einschränkungen sind gerätespezifisch in der Typenliste gekennzeichnet.
The annexes are part of this EU declaration.
*Limitation of standards are marked with a sign in the attached type list.
(i.V. J. Schäfer, Quality Manager)
(H. Nowicki, CSO)
Richtlinien:
Directives:
Angewandte Normen /
Applied standards:
2011/65/EU
RoHS-Richtlinie
RoHS directive
2014/53/EU
RED
Radio Equipment Dire
Zur Beurteilung der Konformität wurden folgende Normen herangezogen:
The assessment of this product has been based on the following standards:
EN 50364
:2010
EN 50581
:2012
EN 60950-1
:2006 ... A2:2013
EN 61851-1
:2011
EN 61851-22
:2002
ETSI EN 300 330
V2.1.1 :2017
ETSI EN 301 489-1
V2.1.1 :2017
ETSI EN 301 489-3
V2.1.1 :2019-03
WEEE-Reg.-Nr. DE 43 124 402
Seite/page 1 / 2
Ausgabe/revision:
2

Alle Rechte vorbehalten.
Nachdruck und Vervielfältigung
nur mit Genehmigung des Herausgebers.
Bender GmbH & Co. KG
Postfach 1161 • 35301 Grünberg • Deutschland
Londorfer Str. 65 • 35305 Grünberg • Deutschland
Tel.: [phone] • Fax: [phone]
E-Mail: [email protected] • www.bender.de
All rights reserved.
Reprinting and duplicating
only with permission of the publisher.
Bender GmbH & Co. KG
PO Box 1161 • 35301 Grünberg • Germany
Londorfer Str. 65 • 35305 Grünberg • Germany
Tel.: [phone] • Fax: [phone]
E-Mail: [email protected] • www.bender.de
RFID117-L1_D00422_00_M / 08.2020/ pdf / © Bender GmbH & Co. KG, Germany – Subject to change!The specied standards take into account the edition valid until 09/2020 unless otherwise indicated.
Bender GmbH & Co. KG
Postfach 1161 • 35301 Grünberg/Germany
Londorfer Straße 65 • 35305 Grünberg/Germany
Phone: [phone] • Fax: [phone]
E-Mail: [e-mail] • www.bender.de
Produktgruppe
Art.-Nr.
Gerätebezeichnung
Anlage - Typenliste der EU-Konformitätserklärung RFID11x
Annex - Typelist of EU-declaration RFID11x
Product group
Art.-no.
Device type
CC61x
RFID110-L1
B94060110
RFID
RFID114 ohne LEDs
B94060114
RFID
RFID117-L1
B94060117
WEEE-Reg.-Nr. DE 43 124 402
Seite/page 2 / 2
Ausgabe/revision:
2