Bender RFID110-L1 User manual

Manual
EN
RFID110-L1
For use in combination with charge controllers used in
electric vehicle charging stations, wall boxes and street
light charging points
RFID110-L1_D00283_02_M_XXEN/04.2018

Bender GmbH & Co. KG
P.O. Box 1161 • 35301 Grünberg • Germany
Londorfer Strasse 65 • 35305 Grünberg • Germany
Tel.: [phone] • Fax: [phone]
E-Mail: [email protected] • www.bender.de
©Bender GmbH & Co. KG
All rights reserved.
Reprinting only with permission of the publisher.
Subject to change!
Photos: Bender archives

Table of Contents
3
RFID110-L1_D00283_02_M_XXEN/04.2018
1. Important information .................................................................................... 5
1.1 How to use this manual ................................................................................. 5
1.2 Technical support: service and support ................................................... 5
1.3 Delivery conditions .......................................................................................... 6
1.4 Inspection, transport and storage .............................................................. 6
1.5 Disposal ............................................................................................................... 6
1.6 Intended use ...................................................................................................... 6
2. RFID module ..................................................................................................... 8
2.1 Dimensions for mounting ............................................................................. 9
2.2 RFID status LEDs ............................................................................................ 10
2.3 Operation ......................................................................................................... 11
2.4 Integration ....................................................................................................... 11
2.4.1 RJ45 connector pin assignment ............................................................... 11
2.4.2 Host labelling requirements: ..................................................................... 12
2.5 User information ............................................................................................ 12
2.5.1 FCC und ISED statements: .......................................................................... 12
2.5.2 Canada RSS-GEN § 8.4 ................................................................................. 13
3. Technical data ................................................................................................. 14
3.1 Tabular data .................................................................................................... 14
3.2 Standards, approvals, certifications ........................................................ 15
3.3 Ordering information .................................................................................. 15
3.4 Declaration of conformity .......................................................................... 16

Table of Contents
4RFID110-L1_D00283_02_M_XXEN/04.2018

5
RFID110-L1_D00283_02_M_XXEN/04.2018
1. Important information
1.1 How to use this manual
Always keep this manual within easy reach for future reference.
1.2 Technical support: service and support
Technical support by phone or e-mail for all Bender products.
 Questions concerning specific customer applications
 Commissioning
 Troubleshooting
Telephone: [phone]*
Fax: [phone]
In Germany only: 0700BenderHelp (Tel. and Fax)
E-mail: [email protected]
*Available from 7.00 a.m. to 8.00 p.m. 365 days a year (CET/UTC+1)
This manual is intended for qualified personnel working in
electrical engineering and electronics!
This symbol denotes information intended to assist the user
in making optimum use of the product.

Important information
6RFID110-L1_D00283_02_M_XXEN/04.2018
1.3 Delivery conditions
Bender sale and delivery conditions apply. These can be obtained from Bend-
er in printed or electronic format.
1.4 Inspection, transport and storage
Inspect the dispatch and equipment packaging for damage, and compare the
contents of the package with the delivery documents. In the event of damage
in transit, please contact Bender immediately. The devices must only be
stored in areas where they are protected from dust, damp, and spray and drip-
ping water, and in which the specified storage temperatures can be ensured.
1.5 Disposal
Abide by the national regulations and laws governing the disposal of this de-
vice. Ask your supplier if you are not sure how to dispose of the old equip-
ment.
For more information on the disposal of Bender devices, refer to our
homepage at www.bender.de -> Service & support.
1.6 Intended use
This manual provides a description of an RFID module, which can only be used
in combination with Bender charge controllers. The charge controller is de-
signed for use in electric vehicle (EV) charging stations, wall boxes and street
light charging points. This document should be used together with the
charge controller operating manual(s), which can be downloaded from:
www.bender.de/manuals.
The RFID module is a separate PCB which facilitates user interaction with the
charging system and is designed according to ISO14443A/MIFARE. It can be
connected to the charge controller, the main component of a charging sys-
tem, using a standard RJ45 cable.

7
RFID110-L1_D00283_02_M_XXEN/04.2018
Charging is initiated by holding a valid RFID card, which is registered to a
backend system, close to the reader on the RFID module. Charging starts
when the contactor in the charging system is switched on to provide power
flow. In offline operation, the charge controller can optionally allow charging
without authorization or it can authorize users based on RFID and a local
white list of authorized RFID cards.

RFID module
8RFID110-L1_D00283_02_M_XXEN/04.2018
2. RFID module
The RFID module, shown below, contains an antenna, antenna illumination
and status LEDs.
All dimensions in mm
It is a separate PCB that should ideally be placed under a semi-transparent
part of the charging system housing.
The RFID module must be placed at a distance of at least 20
mm from any significant metal surface or metal parts to
ensure optimum RFID reading performance.
CAUTION
Electrostatic discharge (ESD) can damage electronic compo-
nents. Observe the precautions for handling electrostatically
sensitive components in accordance with DIN EN 61340-5-1
and DIN EN 61340-5-2.
Free
Reserved
5 white LEDs Status LEDs
(illuminated during
authorisation process)
102.89
57.09
Charging
Note: Tolerance acc. to ISO 2768 - m

RFID module
9
RFID110-L1_D00283_02_M_XXEN/04.2018
The RFID frequency is 13.56 MHz. Bender uses the PN532 Near Field Com-
munication (NFC) controller for contactless communication, which supports
virtually all RFID/NFC communication means on this frequency. Currently only
passive tags with a UID are read. Further functionality is possible upon
request.
2.1 Dimensions for mounting
All dimensions in mm
The RJ45 cable delivered has a length of 50 cm.
However, cable lengths of < 3 m are possible.
2,68
2,7
2,7
46,70
3
,
1
2,7 7,69
97,5
7,69

RFID module
10 RFID110-L1_D00283_02_M_XXEN/04.2018
2.2 RFID status LEDs
As well as the RFID antenna, the RFID module contains several LEDs: three sta-
tus LEDs, one each in green (Free), yellow (Reserved) and blue (Charging), and
5 white LEDs set in a circular arrangement. The status of the LEDs changes
when charging is initiated by holding a valid RFID card close to the reader on
the RFID module.
 Green LED (Free):
– A continuously lighting LED indicates that the charging system is
free and that no vehicle is connected.
– A slow flashing LED indicates that the charging system is free and
that a vehicle is connected.
 Yellow LED (Reserved):
– A continuously lighting LED indicates that the charging system is
reserved and that no vehicle is connected.
– A slow flashing LED indicates that the charging system is reserved
and that a vehicle is connected.
– A fast flashing LED indicates that the charging system is exchanging
data with the backend and is waiting for an authorisation.
The white LEDs are illuminated during the authorisation process, i.e. in parallel
to the yellow LED, and show the current authorisation using circular light
patterns.
 Blue LED (Charging):
– A slow flashing LED indicates that charging has been authorised
and that a vehicle is charging.
– A fast flashing LED indicates that charging has been authorised, and
that the vehicle is not yet connected or has just been disconnected
from the charging system.
 Fast flashing LEDs (green, yellow and blue) is an indication of one of
the following:
– Authorization has been rejected.
– There is a fault in the charging system.
– The backend is not available.
Consult the charging system manual on what measures can be taken.

RFID module
11
RFID110-L1_D00283_02_M_XXEN/04.2018
2.3 Operation
The status of the LEDs changes when charging is initiated by holding a valid
RFID card close to the reader on the RFID module.
Charging can be terminated when the RFID card is again held in front of the
charging system.
2.4 Integration
The RFID module is integrated solely in conjunction with Bender charge con-
trollers under professional installation. In most cases these charge controllers
implement the functionality of an electric vehicle charging system in which
the RFID module is used to authorize charging transactions.
2.4.1 RJ45 connector pin assignment
Pin number Description
1 I2C (not used for the RFID functionality)
2 I2C (not used for the RFID functionality)
3GND
4 RX PN532
5 TX PN532
63.3V
7 5 V (not used for the RFID functionality)
8GND

RFID module
12 RFID110-L1_D00283_02_M_XXEN/04.2018
2.4.2 Host labelling requirements:
The RFID module is provided with a special label which contains all necessary
information. The use of the RFID module in combination with a special host
may, depending on the circumstances, require additional documentation if:
 The module's Federal Communications Commission (FCC) ID is not
visible when installed in the host
 Or the host is such that end users cannot easily access it (using stand-
ard methods) in order to make its FCC ID visible.
In the above two cases, an additional permanent label is then required which
may state one of the following:
 "Contains RFID module FCC ID: 2AHQO-RFID"
 "Contains FCC ID: 2AHQO-RFID"
2.5 User information
2.5.1 FCC and ISED statements:
FCC § 15.19
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including
interference that may cause undesired operation.

RFID module
13
RFID110-L1_D00283_02_M_XXEN/04.2018
2.5.2 Canada RSS-GEN § 8.4
This device complies with Industry Canada's licence-exempt RSSs. Operation
is subject to the following two conditions:
1. This device may not cause interference
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux con-
ditions suivantes :
1. l'appareil ne doit pas produire de brouillage;
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonc-
tionnement.
FCC § 15.21 (Warning statement)
[Any] changes or modifications not expressly approved by the party respon-
sible for compliance could void the user's authority to operate the equipment.

Technical data
14 RFID110-L1_D00283_02_M_XXEN/04.2018
3. Technical data
3.1 Tabular data
Insulation coordination acc. to IEC 60664-1/IEC 60664-3
Rated voltage ........................................................................................................................................................ 12.5 V
Overvoltage category.....................................................................................................................................................III
Pollution degree .............................................................................................................................................................3
Rated impulse withstand voltage...........................................................................................................................800 V
Rated insulation voltage........................................................................................................................................12.5 V
Altitude..................................................................................................................................................≤ 2000 m AMSL
Nominal voltage/nominal current
Nominal voltage..............................................................................................................................................DC 3.3/5 V
Nominal voltage tolerance .................................................................................................................................... ±5 %
Nominal current.............................................................................................................................................140/64 mA
Frequency
Radio frequency ..............................................................................................................................................13.56 MHz
Environment/EMC
Operating temperature ........................................................................................................................... -30…+70 °C
Climatic conditions acc. to IEC 60721:
Stationary use (IEC 60721-3-3) ............................................3K5 (except condensation, water and formation of ice)
Transport (IEC 60721-3-2) ....................................................................................................................................... 2K2
Long-term storage (IEC 60721-3-1) ........................................................................................................................ 1K2
Mechanical conditions acc. to IEC 60721:
Stationary use (IEC 60721-3-3) ..............................................................................................................................3M4
Transport (IEC 60721-3-2) ......................................................................................................................................2M2
Long-term storage (IEC 60721-3-1) .......................................................................................................................1M3
Connection
Connection to charge controller................................................................................................................via RJ45 cable
Maximum cable length..........................................................................................................................................< 3 m
Other
Protection class ......................................................................................................................................................... IP00
Maximum read distance.....................................................................................................................................100 mm
Weight....................................................................................................................................................................... 25 g

Technical data
15
RFID110-L1_D00283_02_M_XXEN/04.2018
3.2 Standards, approvals, certifications
The RFID110-L1 module has been developed in compliance with:
 ISO 14443A/MIFARE
 EN 50364: 2010
 EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 + AC: 2011
+ A2: 2013
 EN 61851-1: 2011
 EN 61851-22: 2002
 ETSI EN 301 489-1 V2.1.1: 2017
 ETSI EN 301 489-3 V2.1.1 Final Draft: 2017
 EN 300 330 V2.1.1: 2017
 FCC ID: 2AHQO-RFID (FCC Part 15.207/15.209)
 IC: 21240-RFID (ICES 003/RSS 210/RSS Gen)
3.3 Ordering information
Type Art. No.
RFID110-L1(RJ45 cable (length 500 mm) included) B94060110

Technical data
16 RFID110-L1_D00283_02_M_XXEN/04.2018
3.4 Declaration of conformity
Bender GmbH & Co. KG
Postfach 1161 • 35301 Grünberg/Germany
Londorfer Straße 65 • 35305 Grünberg/Germany
Phone: [phone] • Fax: [phone]
E-Mail: [email protected] • www.bender.de
EG - K o n f o r m i t ä t s e r k l ä r u n g
E C - D e c l a r a t i o n o f C o n f o r m i t y
Hersteller: Bender GmbH & Co. KG
Manufacturer:
erklärt in alleiniger Verantwortung, dass das Produkt
declare under our sole responsybility that the product
Produktbezeichnun RFID11x (siehe Anlage)
Product name: RFID11x (see annex)
auf das sich diese Erklärung bezieht, mit den Vorschriften
folgender Europäischen Richtlinien übereinstimmt.
to which this declaration relates, is in conformity with the
following European directives.
Richtlinien: 2011/65/EU RoHS-Richtlinie RoHS directive
Directives: 2014/53/EU RED-Richtlinie RED directive
Zur Beurteilung der Konformität wurden folgende Normen herangezogen:
The assessment of this product has been based on the following standards:
Angewandte Normen / Applied standards:
EN 50364 :2010, EN 50581 :2012
EN 60950-1 :2006 ... A2:2013, EN 61851-1 :2011
EN 61851-22 :2002
ETSI EN 300 330 V2.1.1 :2017
ETSI EN 301 489-1 V2.1.1 :2017
ETSI EN 301 489-3 V2.1.1 Final Draft: 2017
Ort, Datum: Grünberg, den 06.03.2018 Unterschrift:
place, date: signature: ________________________________
(Winfried Möll)
(Geschäftsführer Technologie / CTO)
Anmerkung: Die Anlagen sind Bestandteil dieser EG-Konformitätserklärung.
*Evtl. Normen Einschränkungen sind gerätespezifisch in der Typenliste gekennzeichnet.
Remark: The annexes are part of this declaration.
*Limitation of standards are marked with a sign in the attached type list.
WEEE-Reg.-Nr. DE 43 124 402 Seite/page 1 von 2 Ausgabe/revision: 1

Technical data
17
RFID110-L1_D00283_02_M_XXEN/04.2018
Produktgruppe Art.-Nr. Gerätebezeichnung
Anlage - Typenliste der EG-Konformitätserklärung RFID11x
Annex - Typelist of EC-declaration RFID11x
Product group Art.-no. Device type
CC61x RFID110-L1B94060110
RFID RFID114 ohne LEDsB94060114
WEEE-Reg.-Nr. DE 43 124 402 Seite/page 2 von 2 Ausgabe/revision: 1

Technical data
18 RFID110-L1_D00283_02_M_XXEN/04.2018

Bender GmbH & Co. KG
P.O.Box 1161 • 35301 Grünberg • Germany
Londorfer Strasse 65 • 35305 Grünberg •Germany
Tel.: [phone] • Fax: [phone]
E-Mail: [e-mail] • www.bender.de
Photos: Bender archives BENDER Group