BENDIX ST-1 User manual

1
®
DESCRIPTION
The safety valve protects the air brake system against
excessive air pressure build‑up. The valve consists of a
spring‑loaded ball valve subjected to reservoir pressure
which will permit air to exhaust reservoir pressure to
atmosphere, if the reservoir pressure rises above the
valves pressure setting. This pressure is determined by
the force of the spring.
OPERATION
To illustrate the operation of the safety valve, we shall assume
that the governor cut‑out pressure is set at 125 psi. A safety
valve with a setting of 150 psi could then be used. Should
system pressure rise to approximately 150 psi air pressure
would force the ball valve off its seat, and allow reservoir
pressure to vent to atmosphere through the exhaust port
in the spring cage.
When reservoir pressure decreases sufciently, the spring
force will seat the ball check valve, sealing off reservoir
pressure. This would occur at approximately 135 psi for
the 150 psi valve. It is important to note that the desired
pressure setting of the safety valve is determined by
the governor cut‑out pressure. The opening and closing
pressures of the safety valve should always be in excess
of governor cut‑out pressure setting. The pressure setting
is stamped on the lower wrench at of the valve.
Normally, the safety valve remains inoperative and
only functions if for any reason reservoir pressure rises
above the setting of the valve. Constant “popping off” or
exhausting of the safety valve can be caused by a faulty
safety valve, faulty governor, faulty compressor unloading
mechanism, or a combination of any of the preceding.
PREVENTIVE MAINTENANCE
Important: Review the Bendix Warranty Policy before
performing any intrusive maintenance procedures. A
warranty may be voided if intrusive maintenance is
performed during the warranty period.
No two vehicles operate under identical conditions, as
a result, maintenance intervals may vary. Experience is
a valuable guide in determining the best maintenance
interval for air brake system components. At a minimum,
the safety valve should be inspected every 6 months or
1500 operating hours, whichever comes rst, for proper
operation. Should the safety valve not meet the elements
of the operational tests noted in this document, further
investigation and service of the valve may be required.
OPERATING AND LEAKAGE CHECKS
OPERATING TEST: With air pressure in the system, pull
the exposed end of the valve stem removing the spring
load from the ball check valve. Air should exhaust from the
valve’s exhaust port. Release the stem, the air ow should
stop. Failure of valve to pass operating test would indicate
the valve should be disassembled, cleaned and rebuilt.
(See “Disassembly and Assembly” section). If adjustment
is necessary, see “Adjustment” section.
LEAKAGE CHECK: Coat the exhaust port with soap
solution. A leakage of a one (1) inch bubble in 5 seconds is
permitted. Excessive leakage indicates dirt in valve, faulty
ball valve or seat. Valve should be disassembled, cleaned
and rebuilt. (See “Disassembly and Assembly” section).
PRESSURE
SETTING
150 PSI
EXHAUST
PORT
BENDIX®
ST-3™VALVE
BENDIX®
ST-1™VALVE
SD-03-1901
Bendix®ST-1™& ST-3™Safety Valve

2
REMOVAL AND INSTALLATION
REMOVAL
1. Block the wheels or otherwise secure the vehicle and
drain the reservoirs.
2. Using the wrench at closest to reservoir, unscrew valve
from reservoir.
INSTALLATION
The safety valve should be installed in the same reservoir
that the compressor discharge line is connected to. Install
the valve in a convenient location in a top port of the
reservoir. If the safety valve is installed horizontally the
exhaust port should point down and the stem of the valve
should face the rear of the vehicle.
DISASSEMBLY: BENDIX®ST-1™ADJUSTABLE
VALVE
1. Clamp the lower wrench at in a vise (at nearest the
pipe thread).
2. Using the upper wrench at, unscrew the locknut.
Unscrew and remove the spring cage from body of
valve.
3. Remove the ball valve, spring and the release pin from
the spring cage.
DISASSEMBLY: BENDIX® ST-3™
NON-ADJUSTABLE VALVE
1. Clamp the spring cage in soft jawed vise.
2. Using the wrench at, unscrew the body from spring
cage.
3. Remove the ball valve, spring and release pin from
spring cage.
CLEANING AND INSPECTION
Clean all parts in mineral spirits. Inspect all parts thoroughly.
All parts not considered serviceable should be replaced
with genuine Bendix replacement parts.
ASSEMBLY: ST-1 ADJUSTABLE VALVE
1. Place the ball valve in the body.
2. Install the spring and release pin in the spring cage with
the adjusting screw.
3. Position the release pin over the ball valve. Screw the
body with the ball into the spring cage. Tighten securely.
4. Adjust for proper setting (see the “Adjustment” section).
ASSEMBLY: ST-3 NON-ADJUSTABLE VALVE
1. Install the spring and release pin in the spring cage.
2. Position the ball valve in the body and screw the spring
cage onto the body.
3. Hold the spring cage in a soft jawed vise and tighten
the body securely.
TO RAISE THE PRESSURE SETTING
1. Loosen the locknut.
2. Turn the adjusting nut clockwise to obtain the correct
pressure setting.
3. Tighten the locknut.
TO LOWER THE PRESSURE SETTING
1. Loosen the locknut.
2. Turn the adjusting nut counter clockwise to obtain the
correct pressure setting.
3. Tighten the locknut.
TESTING OF REBUILT SAFETY VALVES
Perform the operating and leakage checks.
BENDIX® ST-3™
SAFETY VALVE
ADJUSTING
NUT
SPRING
CAGE
LOCKNUT
SPRING
RELEASE
PIN
BALL
VALVE
PIPE
THREAD
BODY
BENDIX®ST-1™
SAFETY VALVE
BODY
SPRING
CAGE
PIPE
THREAD
BALL
VALVE
SPRING
RELEASE
PIN

3
GENERAL SAFETY GUIDELINES
WARNING! PLEASE READ AND
FOLLOW THESE INSTRUCTIONS
TO AVOID PERSONAL INJURY OR DEATH:
When working on or around a vehicle, the following
guidelines should be observed AT ALL TIMES:
▲Park the vehicle on a level surface, apply the parking
brakes and always block the wheels. Always wear
personal protection equipment.
▲Stop the engine and remove the ignition key when
working under or around the vehicle. When working
in the engine compartment, the engine should be shut
off and the ignition key should be removed. Where
circumstances require that the engine be in operation,
EXTREME CAUTION should be used to prevent personal
injury resulting from contact with moving, rotating,
leaking, heated or electrically-charged components.
▲Do not attempt to install, remove, disassemble or
assemble a component until you have read, and
thoroughly understand, the recommended procedures.
Use only the proper tools and observe all precautions
pertaining to use of those tools.
▲If the work is being performed on the vehicle’s air brake
system, or any auxiliary pressurized air systems, make
certain to drain the air pressure from all reservoirs
before beginning ANY work on the vehicle. If the vehicle
is equipped with a Bendix®AD-IS®air dryer system, a
Bendix®DRM™dryer reservoir module, or a Bendix®
AD-9si™air dryer, be sure to drain the purge reservoir.
▲
Following the vehicle manufacturer’s recommended
procedures, deactivate the electrical system in a manner
that safely removes all electrical power from the vehicle
.
▲Never exceed manufacturer’s recommended pressures.
▲Never connect or disconnect a hose or line containing
pressure; it may whip. Never remove a component or
plug unless you are certain all system pressure has
been depleted.
▲Use only genuine Bendix®brand replacement parts,
components and kits. Replacement hardware, tubing,
hose, fi ttings, etc. must be of equivalent size, type
and strength as original equipment and be designed
specifi cally for such applications and systems.
▲Components with stripped threads or damaged parts
should be replaced rather than repaired. Do not
attempt repairs requiring machining or welding unless
specifi cally stated and approved by the vehicle and
component manufacturer.
▲Prior to returning the vehicle to service, make certain all
components and systems are restored to their proper
operating condition.
▲For vehicles with Automatic Traction Control (ATC),
the ATC function must be disabled (ATC indicator
lamp should be ON) prior to performing any vehicle
maintenance where one or more wheels on a drive axle
are lifted off the ground and moving.
▲The power MUST be temporarily disconnected
from the radar sensor whenever any tests USING A
DYNAMOMETER are conducted on a Bendix®Wingman®
Advanced™-equipped vehicle.
▲You should consult the vehicle manufacturer's
operating and service manuals, and any related
literature, in conjunction with the Guidelines above.
ADJUSTMENT OF SAFETY VALVE
NOTE: The Bendix®ST‑3™safety valve is not adjustable.
The pressure setting of the safety valve is stamped on the
cover wrench at (closest to the pipe thread). The vehicle
manual may also provide the proper pressure setting.
If the setting is not known, determine the governor cut‑
out pressure setting and adjust the safety valve so that
the safety valve closes at a pressure setting somewhat
above governor cut‑out pressure setting (See “Operation”
section).
To adjust, the safety valve must be connected to an air
system with air pressure in excess of desired setting. It
is important that an accurate gauge be used to check
pressure settings while making adjustments.

4BW1583 © 2011 Bendix Commercial Vehicle Systems LLC. All rights reserved. 10/2011 Printed in U.S.A.