Besam PowerSwing User manual

AAE320

The New Besam Swing door operator
PowerSwing

Standard cover Special cover
Door leaf-mounted Double door operators
Main models of the PowerSwing operator

• The operator works electro-hydraulically.
• Closing power from a coil spring
• The open position is kept by a hydraulic valve.
• ”Lock kick” to overcome the resistance of a striking plate
• Dimension standard cover LxHxD 716x110x110 mm

1. Mounting plate
2. Motor/ Pump
3. Valve
4. Hydraulic unit
5. Drive shaft
10. Extension unit, EXA (option)
11. End plate
12. Programme selector, PS-3 (option)
13. Cover
14. Bearing sleeve
15. Cable holder
16. Lid
Identification PowerSwing
6. Spring tube
7. Cable inlet
8. Mains connection
9. Control unit, CSDA

Arm systems
PUSH Arm system PULL Arm system

Wall mounted operator, arm system PUSH
• Decide X
• Draw a line on the wall for the underside of the mounting plate
• Door adaptor should
not be mounted on
glass bead
• Extension has to be
used if operator must
be mounted higher up
on the wall
* Min. 31 mm to
enable drive arm to
pass underneath
Note!

Wall mounted operator, arm system PUSH
• Cut out the appropriate template from the card board box
• Ensure that the template aligns with the drawn line (X) and the L1.
• Use the stickers in the mounting kit to fix the template to the wall
• Punch where to drill
C

Wall mounted operator, arm system PUSH
1. Drill the four mounting holes and the two holes for the door fitting.
2. Remove the template.
3. Tap, plug, or reinforce with rivnuts and screw the drive unit tight.

Mounting the PUSH drive arm
1. Adaptor
2. Drive arm
1. Remove the door fitting from the arm system.
2. Screw the door fitting to the door leaf tight.
3. Mount the drive arm and adaptor on the operator drive shaft at an
angle of 90° to the wall.
4. Ensure that the teeth of the adaptor engage fully with the operator
shaft. Tighten the screw to a torque of 25 Nm. (19 lbf.ft)

Adjusting the PUSH arm
system
1. Telescopic part
2. Drive arm
1. Open the door and connect the
door fitting with the drive arm (do
not tighten the lock screws).
2. Close the door and keep it closed.
3. Turn the drive arm until the
telescopic part is at an angle of 90°
to the door.
4. Tighten the telescopic part with the
lock screws.

Wall mounted operator and arm system PULL
Changing the direction of rotation
1. Mount the washer with the screw in the
drive shaft, one from each side.
2. Dismantle the screws (4 pcs) from the
bearing sleeves on both sides.
3. Fit the tools in the holes, one from each
side and turn both bearing sleeves
simultaneously approx. 165° until the
setting lines in the bearing sleeves are
aligned with the setting lines in the
housing.
4. Remount the four screws in the bearing
sleeves and dismantle the washers and
screws.
5. Setting lines.

Wall mounted operator, arm system PULL
• Decide Z
• Draw a line on the wall for the underside of the mounting plate
• Door adaptor should be
mounted aligned with
upper edge of the door
• Extension has to be
used if operator must be
mounted higher up on the
wall
Note!

Wall mounted operator, arm system PULL
• Cut out the appropriate template from the card board box
• Ensure that the template aligns with the drawn line (Z) and the L1.
• Use the stickers in the mounting kit to fix the template to the wall
• Punch where to drill
C

Wall mounted operator, arm system PULL
1. Drill the four mounting holes and the two holes for the door fitting.
2. Remove the template.
3. Tap, plug, or reinforce with rivnuts and screw the drive unit tight.

Mounting the PULL door fitting
1. Tap, plug, or reinforce with rivnuts and
screw the door fitting tight.
1. Door fitting
2. Door stop
3. Butt hinge

Mounting the PULL drive arm
1. Connect the mains power
2. Open the door to an angle of 90°
3. Give constant impulse by strapping the impulse inputs on the control unit. The operator
drive shaft turns to a factory set position.

Cont. Mounting the PULL drive arm
4. Slide the guide shoe into the door fitting.
5. Mount the drive arm on the operator drive shaft with
the door in unchanged position 90°. Ensure that the
teeth of the adaptor fit well with the operator.
6. Tighten to a torque of 25 Nm (19 lbf.ft)
7. Slide the arm stop against the guide shoe and then
back 20 mm (3/4”). Fasten the arm stop.
8. Remove the strapping. The motor turns off and the
door closes.
9. Snap on the end plates to the door fitting.

Control units
CSDA
This basic control unit is equipped
with inputs for connection of
automatic and manual activation
units.
CSDA-S
This slave control unit is used
together with CSDA for double
doors.

Control units
EXA
This extension unit is mounted on
top of the CSDA to increase the
CSDA functions .
CSDA-F
This unit is used if there are
requirements for extended functions
when the operator is used on fire
doors or for connection of 24 V AC.