Bestway FLOWCLEAR 56385E User manual

GFCI WARNING
WARNING: Risk of electric shock. The GFCI must be tested before
each use.
WARNING: Do not use the pump if this test fails. For assistance,
please visit the support section on our website, www.bestwayusa.com.
POOL SUCTION FITTING INSTRUCTIONS
When installing and using this equipment, basic safety precautions shall always be
followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
READ, FOLLOW, AND UNDERSTAND
ALL INSTRUCTIONS AND WARNINGS.
- Any modification that increases the flow rate of the circulation system shall require
re-evaluation of the cover/grate and sump to ensure that the flow rating of the
Suction Outlet Fitting Assembly (SOFA) is not exceeded.
- Missing, broken, or cracked cover/grates, sumps, mud-frames, or any other SOFA
component shall be replaced before bathers are allowed to use the pool.
- Loose cover/grates shall be reattached before bathers are allowed to use the pool.
1. Replace suction fittings every 2 years.
2. The use of adhesives or other attachment methods that prevent access to suction
piping or SOFA components requiring periodic servicing is prohibited.
3. Refer to the following diagram for each SOFA component part instructions:
4. - Any field modification made to a SOFA not
authorized by the manufacturer’s installation
instructions shall void the SOFA certification.
- No modification shall be made to a SOFA structure
or flow path unless the new configuration has been
certified as new SOFA.
- Cover/grates and all other SOFA components
shall be replaced at or before the end of their
service life and that service life begins the
month and year in which a SOFA component
is installed with or without water.
5. Winterizing instructions. Dry the suction fittings
completely, and store the product in a dry room at a storage temperature of 15 ℃ ~ 40 ℃.
6. Use the screwdriver (not included) to disassemble the suction fitting to clean or service.
- Cover/grate, including fasteners, shall be observed for damage or tampering each
operational day.
- Missing, broken, or cracked cover/grates shall be replaced before bathers are
allowed to use the pool.
- Loose cover/grates and associated components shall be reattached before bathers
are allowed to use the pool.
- SOFA components and fastener receptacles shall be clean and free of debris or
obstructions during installation of cover/grate and fasteners.
- Remember to hand-check cover/grate for snugness to the sump/ frame after
installation.
7. Before using the product, please check the integrity of the head of the suction fitting. If
the product is broken, cracked, or the color has significantly faded, please do not use it.
8. - All SOFAs shall be installed in accordance with the manufacturer’s installation
instructions.
- No modification shall be made to a SOFA structure or flow path unless the new
configuration has been certified to the original SOFA.
- These SOFA-configuration specific flow ratings NOT be exceeded at any time the
pool is open to bathers.
- Cover/grates, when installed, shall not protrude more than 2 in. (51 mm) from the
finished surface of the pool in which the SOFA is installed
9.
Please research and download General Certificate of Conformity through
www.bestwayusa.com
SAVE THESE INSTRUCTIONS
58498E
OWNER’S MANUAL
bestwayusa.com/support
Visit the Bestway YouTube channel

Visit the Bestway YouTube channel
OWNER’S MANUAL
58498E Sand Filter
SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should
always be followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
WARNING - TO REDUCE THE RISK OF INJURY - do not permit children
to use this product unless they are closely supervised at all times.
WARNING - RISK OF ELECTRIC SHOCK - Connect only to a grounding
type receptacle. This product is provided with a ground-fault circuit-interrupter. If replacement of
the plug is needed, use only identical replacement parts.
WARNING - The unit is provided with a ground-fault circuit-interrupter
(GFCI). To test the GFCI, push the test button. The GFCI should interrupt power. Push
the reset button. Power should be restored. If the GFCI fails to operate in this manner,
the GFCI is defective. If the GFCI interrupts power to the pump without the test button
being pushed, a ground current is flowing, indicating the possibility of an electric shock.
Do not use this pump. Disconnect the pump and have the problem corrected by a
qualified service representative before using.
CAUTION - To reduce the risk of electric shock the pool must be installed
no closer than 6 feet (1.8 m) from any electrical outlet. Do not place portable
appliances closer than 5 feet (1.5 m) from the pool.
DO NOT BURY CORD - Locate cord to minimize abuse from lawn mowers, hedge
trimmers, and other equipment.
WARNING - To reduce the risk of electric shock, replace damaged cord
immediately.
WARNING - To reduce the risk of electric shock, do not use extension
cord to connect unit to electric supply; provide a properly located outlet.
CAUTION: This pump is for use with storable pools only. Do not use with
permanently-installed pools. A storable pool is constructed so that it is capable of
being readily disassembled for storage and reassembled to its original integrity. A
permanently-installed pool is constructed in or on the ground or in a building such that
it cannot be readily disassembled for storage.
Please examine and verify all sand filter components are present before use. Notify
Bestway at the customer service address listed on this manual for any damaged or
missing parts at the time of purchase.
• THERMALLY PROTECTED MOTOR. CSA ENCLOSURE 3
• FOR USE WITH SWIMMING POOLS ONLY.
CAUTION: TO ENSURE CONTINUED PROTECTION AGAINST SHOCK
HAZARD,USE ONLY IDENTICAL REPLACEMENT PARTS WHEN SERVICING.
WARNING: RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A
GROUNDING TYPE RECEPTACLE.
CAUTION: THIS PUMP IS FOR USE WITH STORABLE POOLS ONLY - DO
NOT USE WITH PERMANENTLY-INSTALLED POOLS.
CAUTION: CONNECT ONLY TO GROUNDING TYPE RECEPTACLE
PROTECTED BY A CLASS A GROUND FAULT CIRCUIT INTERRUPTER.
CAUTION: FOR CONTINUED PROTECTION AGAINST POSSIBLE ELECTRIC
SHOCK THIS UNIT IS TO BE MOUNTED TO THE BASE IN ACCORDANCE WITH THE
INSTALLATION INSTRUCTIONS.
WARNING - RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin.
2) Inspect Cord Before Using – Do Not Use If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground.
4) Do Not Touch Plug With Wet Hands.
5) Double Insulated – When Servicing Use Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG
SAVE THESE INSTRUCTIONS.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
WARNING: Any changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
2
GFCI WARNING
WARNING: Risk of electric shock. The GFCI must be tested before
each use.
WARNING: Do not use the pump if this test fails. For assistance,
please visit the support section on our website, www.bestwayusa.com.
POOL SUCTION FITTING INSTRUCTIONS
When installing and using this equipment, basic safety precautions shall always be
followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
READ, FOLLOW, AND UNDERSTAND
ALL INSTRUCTIONS AND WARNINGS.
- Any modification that increases the flow rate of the circulation system shall require
re-evaluation of the cover/grate and sump to ensure that the flow rating of the
Suction Outlet Fitting Assembly (SOFA) is not exceeded.
- Missing, broken, or cracked cover/grates, sumps, mud-frames, or any other SOFA
component shall be replaced before bathers are allowed to use the pool.
- Loose cover/grates shall be reattached before bathers are allowed to use the pool.
1. Replace suction fittings every 2 years.
2. The use of adhesives or other attachment methods that prevent access to suction
piping or SOFA components requiring periodic servicing is prohibited.
3. Refer to the following diagram for each SOFA component part instructions:
4. - Any field modification made to a SOFA not
authorized by the manufacturer’s installation
instructions shall void the SOFA certification.
- No modification shall be made to a SOFA structure
or flow path unless the new configuration has been
certified as new SOFA.
- Cover/grates and all other SOFA components
shall be replaced at or before the end of their
service life and that service life begins the
month and year in which a SOFA component
is installed with or without water.
5. Winterizing instructions. Dry the suction fittings
completely, and store the product in a dry room at a storage temperature of 15 ℃ ~ 40 ℃.
6. Use the screwdriver (not included) to disassemble the suction fitting to clean or service.
- Cover/grate, including fasteners, shall be observed for damage or tampering each
operational day.
- Missing, broken, or cracked cover/grates shall be replaced before bathers are
allowed to use the pool.
- Loose cover/grates and associated components shall be reattached before bathers
are allowed to use the pool.
- SOFA components and fastener receptacles shall be clean and free of debris or
obstructions during installation of cover/grate and fasteners.
- Remember to hand-check cover/grate for snugness to the sump/ frame after
installation.
7. Before using the product, please check the integrity of the head of the suction fitting. If
the product is broken, cracked, or the color has significantly faded, please do not use it.
8. - All SOFAs shall be installed in accordance with the manufacturer’s installation
instructions.
- No modification shall be made to a SOFA structure or flow path unless the new
configuration has been certified to the original SOFA.
- These SOFA-configuration specific flow ratings NOT be exceeded at any time the
pool is open to bathers.
- Cover/grates, when installed, shall not protrude more than 2 in. (51 mm) from the
finished surface of the pool in which the SOFA is installed
9.
Please research and download General Certificate of Conformity through
www.bestwayusa.com
SAVE THESE INSTRUCTIONS
WE SUGGEST NOT TO RETURN
THE PRODUCT TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
For FAQ, Manuals, Videos Or
Spare Parts, Please Visit
bestwayusa.com/support
V
i
s
i
t
w
w
w
.
b
e
s
t
w
a
y
u
s
a
.
c
o
m
/
s
u
p
p
o
r
t
f
o
r
h
e
l
p

SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should
always be followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
WARNING - TO REDUCE THE RISK OF INJURY - do not permit children
to use this product unless they are closely supervised at all times.
WARNING - RISK OF ELECTRIC SHOCK - Connect only to a grounding
type receptacle. This product is provided with a ground-fault circuit-interrupter. If replacement of
the plug is needed, use only identical replacement parts.
WARNING - The unit is provided with a ground-fault circuit-interrupter
(GFCI). To test the GFCI, push the test button. The GFCI should interrupt power. Push
the reset button. Power should be restored. If the GFCI fails to operate in this manner,
the GFCI is defective. If the GFCI interrupts power to the pump without the test button
being pushed, a ground current is flowing, indicating the possibility of an electric shock.
Do not use this pump. Disconnect the pump and have the problem corrected by a
qualified service representative before using.
CAUTION - To reduce the risk of electric shock the pool must be installed
no closer than 6 feet (1.8 m) from any electrical outlet. Do not place portable
appliances closer than 5 feet (1.5 m) from the pool.
DO NOT BURY CORD - Locate cord to minimize abuse from lawn mowers, hedge
trimmers, and other equipment.
WARNING - To reduce the risk of electric shock, replace damaged cord
immediately.
WARNING - To reduce the risk of electric shock, do not use extension
cord to connect unit to electric supply; provide a properly located outlet.
CAUTION: This pump is for use with storable pools only. Do not use with
permanently-installed pools. A storable pool is constructed so that it is capable of
being readily disassembled for storage and reassembled to its original integrity. A
permanently-installed pool is constructed in or on the ground or in a building such that
it cannot be readily disassembled for storage.
Please examine and verify all sand filter components are present before use. Notify
Bestway at the customer service address listed on this manual for any damaged or
missing parts at the time of purchase.
• THERMALLY PROTECTED MOTOR. CSA ENCLOSURE 3
• FOR USE WITH SWIMMING POOLS ONLY.
CAUTION: TO ENSURE CONTINUED PROTECTION AGAINST SHOCK
HAZARD,USE ONLY IDENTICAL REPLACEMENT PARTS WHEN SERVICING.
WARNING: RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A
GROUNDING TYPE RECEPTACLE.
CAUTION: THIS PUMP IS FOR USE WITH STORABLE POOLS ONLY - DO
NOT USE WITH PERMANENTLY-INSTALLED POOLS.
CAUTION: CONNECT ONLY TO GROUNDING TYPE RECEPTACLE
PROTECTED BY A CLASS A GROUND FAULT CIRCUIT INTERRUPTER.
CAUTION: FOR CONTINUED PROTECTION AGAINST POSSIBLE ELECTRIC
SHOCK THIS UNIT IS TO BE MOUNTED TO THE BASE IN ACCORDANCE WITH THE
INSTALLATION INSTRUCTIONS.
WARNING - RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin.
2) Inspect Cord Before Using – Do Not Use If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground.
4) Do Not Touch Plug With Wet Hands.
5) Double Insulated – When Servicing Use Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG
SAVE THESE INSTRUCTIONS.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
WARNING: Any changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
3
GFCI WARNING
WARNING: Risk of electric shock. The GFCI must be tested before
each use.
WARNING: Do not use the pump if this test fails. For assistance,
please visit the support section on our website, www.bestwayusa.com.
POOL SUCTION FITTING INSTRUCTIONS
When installing and using this equipment, basic safety precautions shall always be
followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
READ, FOLLOW, AND UNDERSTAND
ALL INSTRUCTIONS AND WARNINGS.
- Any modification that increases the flow rate of the circulation system shall require
re-evaluation of the cover/grate and sump to ensure that the flow rating of the
Suction Outlet Fitting Assembly (SOFA) is not exceeded.
- Missing, broken, or cracked cover/grates, sumps, mud-frames, or any other SOFA
component shall be replaced before bathers are allowed to use the pool.
- Loose cover/grates shall be reattached before bathers are allowed to use the pool.
1. Replace suction fittings every 2 years.
2. The use of adhesives or other attachment methods that prevent access to suction
piping or SOFA components requiring periodic servicing is prohibited.
3. Refer to the following diagram for each SOFA component part instructions:
4. - Any field modification made to a SOFA not
authorized by the manufacturer’s installation
instructions shall void the SOFA certification.
- No modification shall be made to a SOFA structure
or flow path unless the new configuration has been
certified as new SOFA.
- Cover/grates and all other SOFA components
shall be replaced at or before the end of their
service life and that service life begins the
month and year in which a SOFA component
is installed with or without water.
5. Winterizing instructions. Dry the suction fittings
completely, and store the product in a dry room at a storage temperature of 15 ℃ ~ 40 ℃.
6. Use the screwdriver (not included) to disassemble the suction fitting to clean or service.
- Cover/grate, including fasteners, shall be observed for damage or tampering each
operational day.
- Missing, broken, or cracked cover/grates shall be replaced before bathers are
allowed to use the pool.
- Loose cover/grates and associated components shall be reattached before bathers
are allowed to use the pool.
- SOFA components and fastener receptacles shall be clean and free of debris or
obstructions during installation of cover/grate and fasteners.
- Remember to hand-check cover/grate for snugness to the sump/ frame after
installation.
7. Before using the product, please check the integrity of the head of the suction fitting. If
the product is broken, cracked, or the color has significantly faded, please do not use it.
8. - All SOFAs shall be installed in accordance with the manufacturer’s installation
instructions.
- No modification shall be made to a SOFA structure or flow path unless the new
configuration has been certified to the original SOFA.
- These SOFA-configuration specific flow ratings NOT be exceeded at any time the
pool is open to bathers.
- Cover/grates, when installed, shall not protrude more than 2 in. (51 mm) from the
finished surface of the pool in which the SOFA is installed
9.
Please research and download General Certificate of Conformity through
www.bestwayusa.com
SAVE THESE INSTRUCTIONS

SAFETY INSTRUCTIONS
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should
always be followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
WARNING - TO REDUCE THE RISK OF INJURY - do not permit children
to use this product unless they are closely supervised at all times.
WARNING - RISK OF ELECTRIC SHOCK - Connect only to a grounding
type receptacle. This product is provided with a ground-fault circuit-interrupter. If replacement of
the plug is needed, use only identical replacement parts.
WARNING - The unit is provided with a ground-fault circuit-interrupter
(GFCI). To test the GFCI, push the test button. The GFCI should interrupt power. Push
the reset button. Power should be restored. If the GFCI fails to operate in this manner,
the GFCI is defective. If the GFCI interrupts power to the pump without the test button
being pushed, a ground current is flowing, indicating the possibility of an electric shock.
Do not use this pump. Disconnect the pump and have the problem corrected by a
qualified service representative before using.
CAUTION - To reduce the risk of electric shock the pool must be installed
no closer than 6 feet (1.8 m) from any electrical outlet. Do not place portable
appliances closer than 5 feet (1.5 m) from the pool.
DO NOT BURY CORD - Locate cord to minimize abuse from lawn mowers, hedge
trimmers, and other equipment.
WARNING - To reduce the risk of electric shock, replace damaged cord
immediately.
WARNING - To reduce the risk of electric shock, do not use extension
cord to connect unit to electric supply; provide a properly located outlet.
CAUTION: This pump is for use with storable pools only. Do not use with
permanently-installed pools. A storable pool is constructed so that it is capable of
being readily disassembled for storage and reassembled to its original integrity. A
permanently-installed pool is constructed in or on the ground or in a building such that
it cannot be readily disassembled for storage.
Please examine and verify all sand filter components are present before use. Notify
Bestway at the customer service address listed on this manual for any damaged or
missing parts at the time of purchase.
• THERMALLY PROTECTED MOTOR. CSA ENCLOSURE 3
• FOR USE WITH SWIMMING POOLS ONLY.
CAUTION: TO ENSURE CONTINUED PROTECTION AGAINST SHOCK
HAZARD,USE ONLY IDENTICAL REPLACEMENT PARTS WHEN SERVICING.
WARNING: RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A
GROUNDING TYPE RECEPTACLE.
CAUTION: THIS PUMP IS FOR USE WITH STORABLE POOLS ONLY - DO
NOT USE WITH PERMANENTLY-INSTALLED POOLS.
CAUTION: CONNECT ONLY TO GROUNDING TYPE RECEPTACLE
PROTECTED BY A CLASS A GROUND FAULT CIRCUIT INTERRUPTER.
CAUTION: FOR CONTINUED PROTECTION AGAINST POSSIBLE ELECTRIC
SHOCK THIS UNIT IS TO BE MOUNTED TO THE BASE IN ACCORDANCE WITH THE
INSTALLATION INSTRUCTIONS.
WARNING - RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded Outlet. Do Not Remove Ground Pin.
2) Inspect Cord Before Using – Do Not Use If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry And Off The Ground.
4) Do Not Touch Plug With Wet Hands.
5) Double Insulated – When Servicing Use Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG
SAVE THESE INSTRUCTIONS.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
WARNING: Any changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
GFCI WARNING
WARNING: Risk of electric shock. The GFCI must be tested before
each use.
WARNING: Do not use the pump if this test fails. For assistance,
please visit the support section on our website, www.bestwayusa.com.
POOL SUCTION FITTING INSTRUCTIONS
When installing and using this equipment, basic safety precautions shall always be
followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
READ, FOLLOW, AND UNDERSTAND
ALL INSTRUCTIONS AND WARNINGS.
- Any modification that increases the flow rate of the circulation system shall require
re-evaluation of the cover/grate and sump to ensure that the flow rating of the
Suction Outlet Fitting Assembly (SOFA) is not exceeded.
- Missing, broken, or cracked cover/grates, sumps, mud-frames, or any other SOFA
component shall be replaced before bathers are allowed to use the pool.
- Loose cover/grates shall be reattached before bathers are allowed to use the pool.
1. Replace suction fittings every 2 years.
2. The use of adhesives or other attachment methods that prevent access to suction
piping or SOFA components requiring periodic servicing is prohibited.
3. Refer to the following diagram for each SOFA component part instructions:
4. - Any field modification made to a SOFA not
authorized by the manufacturer’s installation
instructions shall void the SOFA certification.
- No modification shall be made to a SOFA structure
or flow path unless the new configuration has been
certified as new SOFA.
- Cover/grates and all other SOFA components
shall be replaced at or before the end of their
service life and that service life begins the
month and year in which a SOFA component
is installed with or without water.
5. Winterizing instructions. Dry the suction fittings
completely, and store the product in a dry room at a storage temperature of 15 ℃ ~ 40 ℃.
6. Use the screwdriver (not included) to disassemble the suction fitting to clean or service.
- Cover/grate, including fasteners, shall be observed for damage or tampering each
operational day.
- Missing, broken, or cracked cover/grates shall be replaced before bathers are
allowed to use the pool.
- Loose cover/grates and associated components shall be reattached before bathers
are allowed to use the pool.
- SOFA components and fastener receptacles shall be clean and free of debris or
obstructions during installation of cover/grate and fasteners.
- Remember to hand-check cover/grate for snugness to the sump/ frame after
installation.
7. Before using the product, please check the integrity of the head of the suction fitting. If
the product is broken, cracked, or the color has significantly faded, please do not use it.
8. - All SOFAs shall be installed in accordance with the manufacturer’s installation
instructions.
- No modification shall be made to a SOFA structure or flow path unless the new
configuration has been certified to the original SOFA.
- These SOFA-configuration specific flow ratings NOT be exceeded at any time the
pool is open to bathers.
- Cover/grates, when installed, shall not protrude more than 2 in. (51 mm) from the
finished surface of the pool in which the SOFA is installed
9.
Please research and download General Certificate of Conformity through
www.bestwayusa.com
SAVE THESE INSTRUCTIONS
4
F4030-03
F4030-02
F4030-01

GFCI WARNING
WARNING: Risk of electric shock. The GFCI must be tested before
each use.
WARNING: Do not use the pump if this test fails. For assistance,
please visit the support section on our website, www.bestwayusa.com.
POOL SUCTION FITTING INSTRUCTIONS
When installing and using this equipment, basic safety precautions shall always be
followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
READ, FOLLOW, AND UNDERSTAND
ALL INSTRUCTIONS AND WARNINGS.
- Any modification that increases the flow rate of the circulation system shall require
re-evaluation of the cover/grate and sump to ensure that the flow rating of the
Suction Outlet Fitting Assembly (SOFA) is not exceeded.
- Missing, broken, or cracked cover/grates, sumps, mud-frames, or any other SOFA
component shall be replaced before bathers are allowed to use the pool.
- Loose cover/grates shall be reattached before bathers are allowed to use the pool.
1. Replace suction fittings every 2 years.
2. The use of adhesives or other attachment methods that prevent access to suction
piping or SOFA components requiring periodic servicing is prohibited.
3. Refer to the following diagram for each SOFA component part instructions:
4. - Any field modification made to a SOFA not
authorized by the manufacturer’s installation
instructions shall void the SOFA certification.
- No modification shall be made to a SOFA structure
or flow path unless the new configuration has been
certified as new SOFA.
- Cover/grates and all other SOFA components
shall be replaced at or before the end of their
service life and that service life begins the
month and year in which a SOFA component
is installed with or without water.
5. Winterizing instructions. Dry the suction fittings
completely, and store the product in a dry room at a storage temperature of 15 ℃ ~ 40 ℃.
6. Use the screwdriver (not included) to disassemble the suction fitting to clean or service.
- Cover/grate, including fasteners, shall be observed for damage or tampering each
operational day.
- Missing, broken, or cracked cover/grates shall be replaced before bathers are
allowed to use the pool.
- Loose cover/grates and associated components shall be reattached before bathers
are allowed to use the pool.
- SOFA components and fastener receptacles shall be clean and free of debris or
obstructions during installation of cover/grate and fasteners.
- Remember to hand-check cover/grate for snugness to the sump/ frame after
installation.
7. Before using the product, please check the integrity of the head of the suction fitting. If
the product is broken, cracked, or the color has significantly faded, please do not use it.
8. - All SOFAs shall be installed in accordance with the manufacturer’s installation
instructions.
- No modification shall be made to a SOFA structure or flow path unless the new
configuration has been certified to the original SOFA.
- These SOFA-configuration specific flow ratings NOT be exceeded at any time the
pool is open to bathers.
- Cover/grates, when installed, shall not protrude more than 2 in. (51 mm) from the
finished surface of the pool in which the SOFA is installed
9.
Please research and download General Certificate of Conformity through
www.bestwayusa.com
SAVE THESE INSTRUCTIONS
5
Installation Information label (copy)
Manufacturers name:
GOLEADER INDUSTRIES (JINHUA) CO., LTD.
Cover part number: F4030
Service life of the cover: 2 Years
Cover flow rating: 28 GPM
Installer needs to fill in the balance of the
information and permanently post it as near as
feasible to the pump control. Keep a copy of this
information with the other important pool related
documents.
Configuration and installed orientation:_________
Location:_______
Installed Date:_________

10
15
12
12
23
30
22
21
20
19
18
17
1611
12
13
14
9
8 7
6
5
4
3
2
1
MAX
MIN
Before assembling the sand filter, take a few minutes to become familiar
with all the sand filter parts.
PARTS REFERENCE OVERVIEW
A
x1
x1
x2
x1
x1
x1
x1
x1
x1
x1
x1
x6
x1
x1
x1
x1
x2
x5
x1
x1
x1
x1
x1
x1
x2
x2
x1
B
x1
x1
x2
x1
x1
x1
x1
x1
x1
x1
x1
x6
x1
x1
x1
x1
x0
x4
x1
x1
x1
x1
x1
x1
x2
x2
x0
C
x1
x1
x2
x1
x1
x1
x1
x1
x1
x1
x1
x5
x1
x1
x1
x1
x0
x0
x1
x1
x1
x1
x1
x1
x2
x0
x0
-1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
x2 x2 x0
27
x1 x1 x0
28
x2 x2 x0
29
x1 x1 x1
30
26
26 -2
REF.NO
2524
12
1818 18
27
18
27
29 2928
26
26
-2
26
-1
A
B
C
x3
x2x1
x2 x1 x1
SPECIFICATIONS
Filter Diameter:
Effective Filter Area:
Max. Operating Pressure:
Working sand filter pressure:
Max. Water Temperature:
Sand:
Sand Size:
Sand Capacity:
254 mm
0.05 m2(0.54 ft2)
0.83 Bar(12 PSI)
<0.45 Bar(6.5 PSI)
35°C
Not included
#20 silica sand,0.45-0.85 mm
Approximately 9 kg
A D
520mm
476mm
254mm
GFCI WARNING
WARNING: Risk of electric shock. The GFCI must be tested before
each use.
WARNING: Do not use the pump if this test fails. For assistance,
please visit the support section on our website, www.bestwayusa.com.
POOL SUCTION FITTING INSTRUCTIONS
When installing and using this equipment, basic safety precautions shall always be
followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
READ, FOLLOW, AND UNDERSTAND
ALL INSTRUCTIONS AND WARNINGS.
- Any modification that increases the flow rate of the circulation system shall require
re-evaluation of the cover/grate and sump to ensure that the flow rating of the
Suction Outlet Fitting Assembly (SOFA) is not exceeded.
- Missing, broken, or cracked cover/grates, sumps, mud-frames, or any other SOFA
component shall be replaced before bathers are allowed to use the pool.
- Loose cover/grates shall be reattached before bathers are allowed to use the pool.
1. Replace suction fittings every 2 years.
2. The use of adhesives or other attachment methods that prevent access to suction
piping or SOFA components requiring periodic servicing is prohibited.
3. Refer to the following diagram for each SOFA component part instructions:
4. - Any field modification made to a SOFA not
authorized by the manufacturer’s installation
instructions shall void the SOFA certification.
- No modification shall be made to a SOFA structure
or flow path unless the new configuration has been
certified as new SOFA.
- Cover/grates and all other SOFA components
shall be replaced at or before the end of their
service life and that service life begins the
month and year in which a SOFA component
is installed with or without water.
5. Winterizing instructions. Dry the suction fittings
completely, and store the product in a dry room at a storage temperature of 15 ℃ ~ 40 ℃.
6. Use the screwdriver (not included) to disassemble the suction fitting to clean or service.
- Cover/grate, including fasteners, shall be observed for damage or tampering each
operational day.
- Missing, broken, or cracked cover/grates shall be replaced before bathers are
allowed to use the pool.
- Loose cover/grates and associated components shall be reattached before bathers
are allowed to use the pool.
- SOFA components and fastener receptacles shall be clean and free of debris or
obstructions during installation of cover/grate and fasteners.
- Remember to hand-check cover/grate for snugness to the sump/ frame after
installation.
7. Before using the product, please check the integrity of the head of the suction fitting. If
the product is broken, cracked, or the color has significantly faded, please do not use it.
8. - All SOFAs shall be installed in accordance with the manufacturer’s installation
instructions.
- No modification shall be made to a SOFA structure or flow path unless the new
configuration has been certified to the original SOFA.
- These SOFA-configuration specific flow ratings NOT be exceeded at any time the
pool is open to bathers.
- Cover/grates, when installed, shall not protrude more than 2 in. (51 mm) from the
finished surface of the pool in which the SOFA is installed
9.
Please research and download General Certificate of Conformity through
www.bestwayusa.com
SAVE THESE INSTRUCTIONS
6

LOAD POOL-GRADE FILTER SAND/FLOWCLEAR™ POLYSPHERE.
NOTE: Use only special pool-grade filter sand, free of all limestone or clay: #20 Silica sand 0.45-0.85 mm, approximately one 9 kg bag
should suffice. If you do not use the recommended size of filter sand, filtering performance will be reduced and the sand filter may
damaged, thereby voiding the warranty.
IMPORTANT: We suggest using #20 silica sand with your pool sand filter. It is specially graded to trap particles in the 20 - 100 micron
range. Some small debris can pass throw the sand and back into the pool. This is normal, especially if the debris is fine or silt.
To limit this, it is better to follow the maintenance instructions, and backwash and rinse when necessary.
We also suggest contacting your pool dealer for the chemical product specifically made to clean the sand. The correct maintenance of
the sand will optimize the cleaning efficiency and avoid accumulation of oils or scale.
When you are vacuuming the bottom of the pool that has a large amount of debris, we suggest to backwash the sand when you finish
cleaning half of the pool.
Remember to backwash and rinse the sand after vacuuming the bottom of the pool each time.
NOTE:
To avoid damaging the Skimmer when adding sand, pour some water into the Bottom Tank to submerse the Skimmer on the Hub.
NOTE: Sand/Flowclear™ Polysphere not included.
NOTE: Use 0.06 lbs (28 g) Flowclear™ Polysphere to replace 2.20 lbs (1 kg) sand.
1. Carefully remove all components from the package and check to ensure nothing is
damaged. If equipment is damaged, immediately notify the retailer from where the
equipment was purchased.
2. The sand filter should be placed on solid, level ground, preferably a concrete slab.
Position the sand filter so the Ports and Control Valve are accessible for operation,
servicing and winterizing.
3. The sand filter must be vertically fixed on ground or a certain pedestal made of wood
or concrete before use to prevent the sand filter from accidentally falling. Fully
assembled sand filter will exceed 18 kg. The mounting holes should be 8 mm in
diameter and spaced 86 mm apart. Use two bolts and nuts with a maximum of 8 mm
in diameter to fasten the sand filter to the pedestal.
(You will need a screwdriver.)
ASSEMBLY
1
4
78
56
23
Bestway
86mm Φ8
c
D
c
c
c
c
c
#20
0.45-0.85 mm
MAX
MIN
MAX
MIN
GFCI WARNING
WARNING: Risk of electric shock. The GFCI must be tested before
each use.
WARNING: Do not use the pump if this test fails. For assistance,
please visit the support section on our website, www.bestwayusa.com.
POOL SUCTION FITTING INSTRUCTIONS
When installing and using this equipment, basic safety precautions shall always be
followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
READ, FOLLOW, AND UNDERSTAND
ALL INSTRUCTIONS AND WARNINGS.
- Any modification that increases the flow rate of the circulation system shall require
re-evaluation of the cover/grate and sump to ensure that the flow rating of the
Suction Outlet Fitting Assembly (SOFA) is not exceeded.
- Missing, broken, or cracked cover/grates, sumps, mud-frames, or any other SOFA
component shall be replaced before bathers are allowed to use the pool.
- Loose cover/grates shall be reattached before bathers are allowed to use the pool.
1. Replace suction fittings every 2 years.
2. The use of adhesives or other attachment methods that prevent access to suction
piping or SOFA components requiring periodic servicing is prohibited.
3. Refer to the following diagram for each SOFA component part instructions:
4. - Any field modification made to a SOFA not
authorized by the manufacturer’s installation
instructions shall void the SOFA certification.
- No modification shall be made to a SOFA structure
or flow path unless the new configuration has been
certified as new SOFA.
- Cover/grates and all other SOFA components
shall be replaced at or before the end of their
service life and that service life begins the
month and year in which a SOFA component
is installed with or without water.
5. Winterizing instructions. Dry the suction fittings
completely, and store the product in a dry room at a storage temperature of 15 ℃ ~ 40 ℃.
6. Use the screwdriver (not included) to disassemble the suction fitting to clean or service.
- Cover/grate, including fasteners, shall be observed for damage or tampering each
operational day.
- Missing, broken, or cracked cover/grates shall be replaced before bathers are
allowed to use the pool.
- Loose cover/grates and associated components shall be reattached before bathers
are allowed to use the pool.
- SOFA components and fastener receptacles shall be clean and free of debris or
obstructions during installation of cover/grate and fasteners.
- Remember to hand-check cover/grate for snugness to the sump/ frame after
installation.
7. Before using the product, please check the integrity of the head of the suction fitting. If
the product is broken, cracked, or the color has significantly faded, please do not use it.
8. - All SOFAs shall be installed in accordance with the manufacturer’s installation
instructions.
- No modification shall be made to a SOFA structure or flow path unless the new
configuration has been certified to the original SOFA.
- These SOFA-configuration specific flow ratings NOT be exceeded at any time the
pool is open to bathers.
- Cover/grates, when installed, shall not protrude more than 2 in. (51 mm) from the
finished surface of the pool in which the SOFA is installed
9.
Please research and download General Certificate of Conformity through
www.bestwayusa.com
SAVE THESE INSTRUCTIONS
7

A
A
A
A
B
B
A
B
B
D
C
A
B
CONNECT TO THE POOL
V1.1
V1.2
V2
A
D
C
A
B
B
BB
A
B
A
B
A
D
C
A
B
A
D
Garden hose
(not included)
For Drain,
Backwash,
Rinse function
c
D
D
c
D
D
BB
GFCI WARNING
WARNING: Risk of electric shock. The GFCI must be tested before
each use.
WARNING: Do not use the pump if this test fails. For assistance,
please visit the support section on our website, www.bestwayusa.com.
POOL SUCTION FITTING INSTRUCTIONS
When installing and using this equipment, basic safety precautions shall always be
followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
READ, FOLLOW, AND UNDERSTAND
ALL INSTRUCTIONS AND WARNINGS.
- Any modification that increases the flow rate of the circulation system shall require
re-evaluation of the cover/grate and sump to ensure that the flow rating of the
Suction Outlet Fitting Assembly (SOFA) is not exceeded.
- Missing, broken, or cracked cover/grates, sumps, mud-frames, or any other SOFA
component shall be replaced before bathers are allowed to use the pool.
- Loose cover/grates shall be reattached before bathers are allowed to use the pool.
1. Replace suction fittings every 2 years.
2. The use of adhesives or other attachment methods that prevent access to suction
piping or SOFA components requiring periodic servicing is prohibited.
3. Refer to the following diagram for each SOFA component part instructions:
4. - Any field modification made to a SOFA not
authorized by the manufacturer’s installation
instructions shall void the SOFA certification.
- No modification shall be made to a SOFA structure
or flow path unless the new configuration has been
certified as new SOFA.
- Cover/grates and all other SOFA components
shall be replaced at or before the end of their
service life and that service life begins the
month and year in which a SOFA component
is installed with or without water.
5. Winterizing instructions. Dry the suction fittings
completely, and store the product in a dry room at a storage temperature of 15 ℃ ~ 40 ℃.
6. Use the screwdriver (not included) to disassemble the suction fitting to clean or service.
- Cover/grate, including fasteners, shall be observed for damage or tampering each
operational day.
- Missing, broken, or cracked cover/grates shall be replaced before bathers are
allowed to use the pool.
- Loose cover/grates and associated components shall be reattached before bathers
are allowed to use the pool.
- SOFA components and fastener receptacles shall be clean and free of debris or
obstructions during installation of cover/grate and fasteners.
- Remember to hand-check cover/grate for snugness to the sump/ frame after
installation.
7. Before using the product, please check the integrity of the head of the suction fitting. If
the product is broken, cracked, or the color has significantly faded, please do not use it.
8. - All SOFAs shall be installed in accordance with the manufacturer’s installation
instructions.
- No modification shall be made to a SOFA structure or flow path unless the new
configuration has been certified to the original SOFA.
- These SOFA-configuration specific flow ratings NOT be exceeded at any time the
pool is open to bathers.
- Cover/grates, when installed, shall not protrude more than 2 in. (51 mm) from the
finished surface of the pool in which the SOFA is installed
9.
Please research and download General Certificate of Conformity through
www.bestwayusa.com
SAVE THESE INSTRUCTIONS
8
(1)
(2)
(3)

Before switching on, please read the manual carefully.
FOR POOL WITH 1.25 IN. (32 MM) VALVE
STOP
OPERATION
GFCI TEST
1 2 3 4
CONTROL VALVE OVERVIEW
WARNING: To prevent equipment damage and possible injury, always
switch off sand filter before changing the Control Valve function. Changing
valve positions while the pump is running can damage the Control Valve,
which may cause personal injury or property damage.
How to Use the Control Valve:
Press down on the Control Valve handle and rotate to desired function.
CONTROL VALVE FUNCTIONS
The Control valve is used to select 6 different filter functions: Filter, Rinse,
Circulate, Backwash, Closed and Drain.
Filter: This function is used to filter pool
water and should be positioned here 99%
of the time. Water is pumped through the
sand filter, where it is cleaned and
returned to the pool.
B
C
A
Closed: This function stops water
flowing between the sand filter and
the pool.
C
B
A
RESET
TEST
RESET
TEST
RESET
TEST
A
26-1
B
26-2
c
D
D
A
C
Bestway
9

C
B
A
D
Backwash: This function is used to clean the
sand bed; water is pumped down through the
Collector Hub, upwards through the sand bed,
and deposited out of Port D.
C
B
D
A
Rinse: This function for initial startup, cleaning,
and sand bed leveling after Backwash; water is
pumped downwards through the sand bed, up
through the Collector Hub and deposited out of
the valve Port D.
C
B
D
A
Drain: This function drains water from the pool;
another filter bypass setting, water is pumped and
deposited out of Port D, instead of returning it to
the pool.
C
B
A
Circulate: This function circulates pool water
by passing the sand filter; use this function if the
filter is broken to collect debris in the Debris
Screens.
NOTE:
• Be sure all provisions for wastewater disposal meet applicable local, state or national codes. Do not discharge water
where it will cause flooding or damage.
•
When the Control Valve is set to the Backwash, Rinse, or Drain position, water will discharge from Port D on the Control Valve.
• Do not switch on or operate the sand filter with the Control Valve set to the Closed function or it will seriously damage the sand filter.
• Do not set the Control Valve between two functions, or it will lead to leaking.
• To avoid water leakage, screw the Port D Cap onto the Control Valve Port D before operating the sand filter.
AIR RELEASE
Press down the control valve handle and wait untill the water flow from Port D to release the air.
NOTE: It is important to repeat this operation every time you start the pump after winterizing, maintenance and backwashing the
sand bed.
FIRST TIME USE INSTRUCTIONS
Backwash and Rinsing must be performed to prepare the pump for its first use and to wash the sand.
CAUTION: DO NOT DRY RUN THE SAND FILTER
1. Press down on the Control Valve handle and rotate to the Backwash function.
2. Plug in and run the sand filter for 3-5 minutes, or until the water runs clear.
3. Switch off the sand filter and set the Control Valve to the Rinse function.
4. Switch on the sand filter and run the sand filter for 1 min. This circulates
water backwards through the sand filter and drains water out Port D.
5. Switch off the sand filter. Set the Control Valve to the Closed function.
6. Top up pool water if required.
IMPORTANT: This procedure removes water from the pool, which you’ll need to replace. Switch off the sand filter immediately if water
levels near the pool’s Inlet and Outlet valves.
Backwash Rinsing
10

1.6
0
5
10 15
20
23
1.4
1.2
1
0.8
0.6
0.4
0.2
0
psi
bar
In areas that have freezing winter temperatures, pool equipment must be winterized to protect against damage. Allowing water
to freeze will damage the sand filter and void warranty.
1. Backwash the sand filter.
2. Drain the pool according to the pool owner’s manual.
3. Unscrew the drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect the two Hoses from the pool and the sand filter.
5. Completely pour the sand out of the tank and dry all components.
6. Store the sand filter in a dry location out of child’s reach.
STORAGE
1. Switch off the sand filter and set Control Valve to the Drain function.
2. Detach the Hose from the connection valve’s Port A and sand filter Port A and attach to Port D.
3. Switch on the sand filter to remove pool water.
WARNING: DO NOT DRY RUN THE SAND FILTER.
LOWERING OR DRAINING POOL WATER
CLEANING THE STRAINER
1. Switch off the sand filter and set the Control Valve to the Closed function.
2. Close the connection valves.
3. Remove the Strainer Cover by unscrewing it.
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position. Ensure the hole in the strainer is aligned.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Open the connection valves.
NOTE: The Strainer must be emptied and cleaned periodically. A dirty or blocked
strainer will reduce the performance of the sand filter.
1. Now the sand filter is ready for use. Set the Control Valve to the Filter function.
NOTE: To prevent the risk of electrical shock dry any excess water from yourself
and the sand filter.
2. Switch on the sand filter to run it.
NOTE: The sand filter has now started its filtering cycle. Check that water is returning
to the pool and take note of the filter pressure on Pressure Gauge. Generally, the
recommended sand filter pressure is less than 0.45 Bar (6.5 PSI) when it is running.
CAUTION: You must ensure the sand filter is switched off and unplugged before any
maintenance begins or severe risk of injury or death exists.
As dirt builds up in the sand filter, the pressure reading on Pressure Gauge will
increase. When the Pressure Gauge is 0.45 Bar (6.5 PSI) or higher, or water flow to
the pool is too low, it is time to clean the sand.
To clean the sand bed, follow all instructions outlined previously in: Backwash and
Rinsing.
NOTE:
1. The Pressure Gauge is just used for measuring the water pressure, not used for
precision measurement.
2. We recommend you clean the sand bed once a month or less regularly depending
on how often
the pool is used. Do not clean the sand too frequently.
SAND FILTER MAINTENANCE
11

303021292431
For support please visit us at:
bestwayusa.com/support
©2022 Bestway Inflatables & Material Corp.
All rights reserved
Trademarks used in some countries under license from Bestway Inflatables & Material Corp., Shanghai, China
Exported by Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited
Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong
Distributed in North America by Bestway (USA) Inc., 3435 S. McQueen Road, Chandler, AZ 85286, United States of America
Tel: [phone]
www.bestwayusa.com
Problems Probable Causes Solutions
Sand is flowing to
the pool
- Recommend 0.45 mm to 0.85 mm #20 silica sand
- Stop the sand filter every time set the control valve
- Check if the level of the sand is between the marked
“MAX” and “ MIN” on the hub
- Replace the skimmer
Sand Filter does
not operate - GFCI broken
No water flow
Excessive filter
pressure
- Dirty filter
- Calcified sand bed
- Insufficient backwashing
- The pressure gauge is broken
- Backwash
- Inspect sand and change if necessary
- Backwash until water runs clear
- Replace the pressure gauge
Control Valve leaks
from the port D
Connectors leaks
- Control Valve is set between two
functions
- The gasket is broken
- Set to one function
- Replace the gasket
- Washer of the connectors not in place
- Washer of the connectors broken
- O-ring on the hose connection is broken
- Loose Hoses
- Reposition the washer
- Replace the washer
- Replace the o-ring
- Tighten them
- Stopper plugs were not removed
- Air was not released
- The control valve is set to Closed
- The strainer is blocked
- Sand filter broken
- Remove the stopper plugs and insert the
debris screens
- Release the air
- Set to filter function
- Clean the strainer
- Call for service
- Sand is too small
- Move the control valve from the
backwash to the filter function without
stop the sand filter
- The level of the sand is too high
- The skimmer is broken
- For assistance, please visit the support section
on our website, www.bestwayusa.com.
TROUBLESHOOTING
GFCI LED flash
- Plug may be loose in the socket; the
internal metal part of the plug doesn't
guarantee a secure connection
- Replace the socket
- Replace the pump