Better Bathrooms BeBa 27010 User manual

1
WALL MOUNTED LED MIRROR
BeBa_27010
BeBa_27579
•LED LIGHTING
•TOUCH SENSOR CONTROL
•DEMISTER
•IP44 INGRESS PROTECTION

2
CONGRATULATIONS ON YOUR PURCHASE
Our aim at Better Bathrooms is to bring you extraordinary bathroom products, for less.
If you’re after a modern, traditional, or a totally unique style bathroom, we have the fittings
and fixtures to bring your ideas to life, so you can fall in love with your space every day.
We hope you’re happy with your new product. But if you experience any problems, we’re
always here to help.
•Call our friendly UK call centre on 0330 390 3062
(Lines open 9am-4.30pm Monday to Friday, or 9am-2pm Saturday).
•Send us a message via betterbathrooms.com.
CONTENTS
SAFETY
3
BATHROOM ZONES
4
PARTS SUPPLIED
5
TOOLS REQUIRED
5
INSTALLING THE MIRROR
6
OPERATION
7
CLEANING AND MAINTENANCE
8
TECHNICAL SPECIFICATIONS
8

3
SAFETY
•This mirror should be installed by a qualified electrician.
•This fitting is only suitable for connection to a 220-240V earthed supply in accordance
with current IEE wiring regulations, and should be installed in accordance with local
Building Regulations.
•This is for domestic, indoor use only.
•The fitting should be connected to a dedicated lighting circuit which must be
protected by a 5-amp fuse (or a 6 amp miniature circuit breaker).
•The electrical connection must be an adequate distance from the rear of the mirror to
prevent the risk of shorting with the mirror’s casing.
•Before installing the fitting ensure that the mains supply is switched off, and that the
appropriate fuse is removed (or appropriate circuit breaker is switched off) before
commencing installation. Ensure that measures are taken to prevent the supply from
being inadvertently reconnected.
•If there is a “Minimum Distance” label, please do not allow flammable materials to
rest within that distance from the unit.
•This product may contain delicate parts –be careful during handling and
maintenance to avoid breakage.
•If any modification is made to the fitting will invalidate the warranty and may render
the product unsafe.
•A defective appliance may cause electric shock. Never switch on a defective or
damaged appliance. Disconnect the appliance from the mains before seeking
assistance.
•This product is IP44 rated, and no part of the installation is allowed to be within
bathroom Zones 0 or 1. Installation is permitted within Zone 2.
•This product must be earthed. Before commencing installation, ensure that there are
no pipes or wires located behind the wall that may be damaged during drilling.
•Ensure that the hanging location has been decided upon and marked clearly to avoid
unwanted damage to the wall due to incorrect positioning.
•Inspect the mirror to ensure there are no signs of damage prior to installation.
•Take care unpacking, do not use a sharp blade to open as this may damage the mirror
and void your warranty.
•Once installed a bead of silicon can be applied between the mirror and the wall
across the top and sides of the unit. Never seal the bottom of the mirror to the wall,
as this may allow water to accumulate behind the mirror.

4
BATHROOM ZONES
Zone 0:
The interior of the bathtub or shower basin.
Zone 1:
The area around the bathtub or shower basin up
to a height of 2.25m above the floor
Zone 2:
The area stretching to 0.6m outside the bath or
shower and above the bath or shower if over
2.25m

5
PARTS SUPPLIED
WALL PLUGS (X2)
SCREWS M4 (X2)
PLEASE NOTE: It is the installers responsibility to ensure that the fittings are suitable for the type of wall.
Alternative fittings may be required (Not Supplied). If unsure professional advice should be sought.
TOOLS REQUIRED tool
TAPE MEASURE
SPIRIT LEVEL
ELECTRIC DRILL
SCREWDRIVER
HAMMER
8mm DRILL BIT
PENCIL

6
HANGING THE MIRROR
The mirror should be hung in portrait orientation. At the back of the mirror, there
are 2 key holes on the vertical sides.
To hang the mirror, you will need to drill two holes into the wall, ensuring that
there are no wires or pipes behind the wall before commencing.
1. Ensure that the power is disconnected at the circuit
breaker, and that there is no risk of reconnection during
installation.
2. Measure the distance between the two key holes.
3. Make a note of the distance and mark their position on the
wall. Use a spirit level to ensure that the holes are level.
4. Drill the 2 holes into the wall at the position marked using
a suitable drill bit.
5. Insert the wall plugs into the holes.
6. Insert the screws into the wall plugs, ensuring their heads
are protruding by approximately 3mm.
7. Check to ensure the screws line up correctly and the mirror
can be safely hung from them.
8. The mirror should now be connected to a suitable fuse
spur following current regulations and guidance. When
connecting ensure that enough cable is left to allow the
mirror to be safely removed.
9. You will now be able to hang the mirror. Carefully lower
the mirror onto the screws, ensuring that is secure and will
not slide.
10. Reconnect the power supply.

7
OPERATION
Tapping the button once
turns on the lights and the
demister.
Tap again to turn the lights
and demister off.
Holding down the button will
change the lights from warm
white to cool white and back
again.

8
CLEANING AND MAINTENANCE
Never use products containing bleach or abrasive cleaners, as these will have a
detrimental effect on the appearance and lifespan of the product.
Use a clean micro fiber cloth to clean the mirror.
TECHNICAL SPECIFICATION
Model
BeBa_27010
BeBa_27579
WxHxD (mm)
600x800x50
600x800x50
Net Weight (Kg)
7.6
7.8
Power Cord
length (cm)
60
60
Rated Power (W)
32W
32
IP Rating
IP44
IP44
Input
220-240V AC 50 Hz
220-240V AC 50 Hz
This product contains a light source of energy efficiency class F.
DISPOSAL
Recycling facilities are now available for all customers at which you can
deposit your old electrical products. Customers will be able to take any old
electrical equipment to participating sites run by their local councils.
Please remember that this equipment will be further handled during the
recycling process, so please be considerate when depositing your
equipment. Please contact the local council for details of your local
household waste recycling centers.
At the time of printing the product contains no substances listed within Annex XIV of the
Reach Regulations (EC) 1907/2006. In accordance with Article 59 of the same regulation the
following substances are contained within the product at permitted levels: Cadmium.
As a responsible manufacturer the regulations are monitored to ensure continued
compliance. Further information can be provided upon request.
V20212806