Better Bathrooms Roxbi BeBa 27636 User manual

•Multi-person assembly
•We always recommend using professional tradespeople
to install your product
V1_13.08.2021
•
Product Code –BeBa_27636 - BeBa_27637 –BeBa_27603 -
Roxbi 600mm Floorstanding Basin Vanity Unit - Drawers

Congratulations on your purchase
And welcome to our growing gang of savvy shoppers
We're on a mission to bring you extraordinary bathroom products, for less. From modern to traditional
style ceramics, plus the gorgeous fixtures, fittings and furniture to match. So, you can fall in love with your
space every single day.
As one of the UK's largest independent bathroom stores, we've received countless awards; including the
National Business Awards UK, the Digital Entrepreneur Awards and being placed on The Sunday Times
Fast Track 100.
We hope your new product exceeds your highest expectations. However, if you experience any problems,
please:
•Log in to your account and contact our costumer services team via your self-serve portal –
betterbathrooms.com/CostumerAccount/Login
•Contact us via betterbathrooms.com/content/contact-us
Important information
•Please read these instructions thoroughly and retain for future reference
•Please ensure the product is installed level on all 4 plains
•Tap flow rate should be reduced to suit the basin, allowing the tap to be turned on fully without over
splashing of the basin
•Use cut out screw holes if provided to fix the furniture to the wall
•Please inspect the product fully for any damage or defects prior to installation
•Ensure the correct waste is installed and is water tight, periodically check the installation for leaks
•Always check all wall before drilling to prevent damage to pipes and cables.
•Always wipe the unit dry after every use and remove any standing water to maintain the
product finish.
Unit Weight (Kg)
Basin Weight (Kg)
Max loading weight in
addition to Unit, basin and
full capacity Drawer (Kg)
Each Drawer Loading Capacity
(Kg)
31,60
11,00
20,00
15,00

Tools required
Troubleshooting
Drawer not straight / not closing
Please refer to drawer adjustment guide
Leaking
Check sealant, reapply if necessary

Installation
Please spend 5 minutes reading this section before commencing with the installation of your new furniture
1. Should any of your items have a defect, please do not install as returns will not be accept once fitted.
2. We advise that you use a qualified person to install your units, as any issues relating to poor fitting will not be accepted by the supplier.
3. This product is water resistant but NOT waterproof and therefore the room must be well ventilated and any standing water must be
wiped dry after use.
4. Please avoid direct sunlight as this will cause the painted surfaces to discolour.
5. Due to motion in transit, the cabinet doors and drawers may need to be adjusted after installation
6. Floor standing units must be secured back to the wall through the back rail using suitable fixings.
7. Basins units should be fitted (See image 8), and then the basin should also be secured where applicable, using Fischer bolts not
supplied) though the fixing points under the basin and/or siliconed between the basin and unit.
8. Fixings and wall type must be sufficient to support the unit, the fixings supplied are for solid wall fixing.
Feet
Nut
Plastic Dowel

Feet
Nut

Info :
1- Drill the holes into the wall at 8 mm diameter and to
a depth of 100 mm.
2- Apply a small amount of silicone into the hole.
3- Insert the dowels(Wall plugs) into the holes and tap
flush to the wall surface using a hammer.

Info :
1- When installing the basin into the unit , apply silicone between the basin and
unit as shown above.
2- For ease, install the basin mixers before installation of the basin.

Drawer Removal
Drawer Adjustment
1- Pull the drawer to yourself.
2- Pull the drawer to outside by
pressing the latch locks at the
same time.
3- Lift the drawer up and out of the
unit.
4- Proceed in the same way for the
each drawers.
1
3
2
1- Push the Number 1 and pull the front of the drawer to yourself

Maintenance
Please note that although these units have been designed to give years of pleasure and satisfaction, you will help maintain the original beauty of your bathroom by
following these guidelines.
Melamine, vinyl and foil wrapped doors
Occasional marks, can in most cases, be removed with a soft damp cloth. More persistent marks can be removed using a non-silicone-
based furniture cleaner. Hot soapy water should be avoided. Once the mark is removed, the area should be wiped over with a damp cloth
to remove any excess and dried with a soft clean cloth. On no account should solvent or an abrasive cleaner be used as permanent
damage to the finish could take place.
High Gloss Doors
Use a cleaning product not containing aggressive substances like acetone, alcohol, bleach etc. as those components could seriously
damage the surface of the door. The best would be to use a soft cotton or micro fibre cloth with only water and a soft soap (containing a
maximum 1% of liquid soap)
Carcass components
Do not use polish on any surfaces. A damp cloth with soapy water will clean off most marks or spills. On no account should any spillage,
even water, be allowed to lie of the surface. Bleaches scouring pads and multi-surface cleaners should not be used.
Drawers, runners, door hinges.
These should be wiped out with a damp soapy cloth and wiped dry with a soft cloth as necessary. The roller runners and hinges are
lubricated and should not be cleaned with a degreasing agent as this will affect the action of the moving parts. Never lean on partially or
fully opened doors and drawers in order to gain access to the units. The hinges are specified to adequately support the weight of the door,
plus small additional weights such as wire accessories. It is advised that once the bathroom has been installed, you should check every six
months that all screws on the hinges are tight.
Worktops
Although the worktop is hard wearing, sharp objects will scratch and excessive heat will scorch the surface. Care should be taken not to
drop any heavy objects onto the worktop as the surface may crack. For cleaning, a damp soapy cloth with clean off most spills. Bleaches,
scouring pads and multi-surface cleaners should not be used. Corrosive liquids and make-up should be wiped off immediately. On no
account should any spillage, even water, be allowed to lie on the surface.
Temperature, humidity, ventilation and proximity
Avoid excessive change in temperature and humidity. We would advise an extractor fan to be installed in all bathrooms which include
furniture to reduce the chance of water ingress damage. The extractor fan should be used every time that the shower/bath is used and
should be left switched on for a sufficient time afterward to allow for adequate ventilation. Ensure that the fan has been correctly sized
for the room in use. The units, under no circumstance, should be fitted in a location where they are regularly subjected to contact with
water.
Cleaning
To maintain the surface of your product, wipe with a clean damp cloth and wipe dry, do not use any
abrasive cleaning agents or materials. If any harsh chemicals come into contact with the surface of the
product, rinse and wipe clean immediately.