Better Bathrooms BeBa-27531 User manual

1
TOUCH CONTROL
LED MIRROR
BeBa_24919
BeBa_27531
•TOUCH CONTROL
•LED LIGHT
•IP44 INGRESS PROTECTION

2
CONGRATULATIONS ON YOUR PURCHASE
Our aim at Better Bathrooms is to bring you extraordinary bathroom products, for less.
If you’re after a modern, traditional, or a totally unique style bathroom, we have the fittings
and fixtures to bring your ideas to life, so you can fall in love with your space every day.
We hope your new product goes above and beyond your expectations. However, should
any problems occur, please:
•Log in to your account and contact our customer services team via your self-service
portal –betterbathrooms.com/CustomerAccount/Login
•Contact us via betterbathrooms.com/contact/contact-us
CONTENTS
SAFETY
3
BATHROOM ZONES
4
PARTS SUPPLIED
5
TOOLS REQUIRED
5
INSTALLING THE MIRROR
6
PRODUCT OVERVIEW
7
OPERATION
7
CLEANING AND MAINTENANCE
8
TECHNICAL SPECIFICATIONS
8

3
SAFETY
•This mirror should be installed by a qualified electrician.
•This fitting is only suitable for connection to a 220-240V earthed supply
in accordance with current IEE wiring regulations, and should be
installed in accordance with local Building Regulations.
•This is for domestic, indoor use only.
•The fitting should be connected to a dedicated lighting circuit which
must be protected by a 5-amp fuse (or a 6-amp miniature circuit
breaker).
•Before installing the fitting ensure the mains supply is switched off, and
that the appropriate fuse is removed (or appropriate circuit breaker is
switched off) before commencing installation. Ensure that measures
are taken to prevent the supply from being inadvertently reconnected.
•If there is a “Minimum Distance” Label, please do not allow Flammable
Materials to rest within that distance from the unit.
•This product may contain delicate parts –be careful during handling
and maintenance to avoid breakage.
•If any modification is made to the fitting it will invalidate the warranty
and may render the product unsafe.
•A defective appliance may cause electric shock. Never switch on a
defective or damaged appliance. Disconnect the appliance from the
mains before seeking assistance.
•This product is IP44 rated, and no part of the installation is allowed to
be within bathroom Zones 0 or 1. Installation is permitted within Zone
2.
•This product must be earthed. Before commencing installation, ensure
that there are no pipes or wires located behind the wall that may be
damaged during drilling.
•Ensure that the hanging location has been decided upon and marked
clearly to avoid unwanted damage in the wall due to incorrect
positioning.
•Check that the mirror is not damaged prior to installation.
•Take care unpacking, do not use a sharp blade to open as this may
damage the mirror and void your warranty.
•Installation must only be carried out by a qualified professional or
electrician.

4
BATHROOM ZONES
Zone 0:
The interior of the bathtub or shower basin.
Zone 1:
The area around the bathtub or shower basin up
to a height of 2.25m above the floor
Zone 2:
The area stretching to 0.6m outside the bath or
shower and above the bath or shower if over
2.25m

5
PARTS SUPPLIED
WALL PLUGS (X2)
SCREWS M4 (X2)
PLEASE NOTE: It is the installers responsibility to ensure that the fittings are suitable for the type of wall.
Alternative fittings may be required (Not Supplied). If unsure professional advice should be sought.
TOOLS REQUIRED tool
TAPE MEASURE
SPIRIT LEVEL
ELECTRIC DRILL
SCREWDRIVER
HAMMER
8mm DRILL BIT
PENCIL

6
INSTALLATION
IMPORTANT: Before commencing installation, ensure that there are no pipes
or wires located behind the wall that you will be drilling into.
•Ensure that the hanging location has been decided upon and marked clearly
to avoid unwanted damage in the wall due to incorrect positioning.
•Check there the mirror is not damaged prior to installation.
•Take care unpacking, do not use a sharp blade to open as this may
damagethe mirror and void your warranty.
At the back of the mirror, there are 2 hanging hooks
spaced across the top. To hang the mirror, two holes are
required in the wall. Before drilling, ensure that no wires
or pipes are behind the wall. If unsure, seek professional
advice.
1. Measure the distance between the centre of the two hanging points.
2. Make a note of the distance and mark their position on the wall. Use a
spirit level to ensure that the marks are level.
3. Drill the 2 holes into the wall at the position marked using a suitable drill
bit.
4. Insert the wall plugs into the holes.
5. Insert the screws into the wall plugs, ensuring their heads are protruding
by approximately 3mm.
6. Check to ensure the screws line up correctly and the mirror can be safely
hung from them.
7. Carefully lower the mirror onto the 2 screws, ensuring that is secure and will
not slide.

7
CONNECTING THE MIRROR
To connect your mirror, it must be first be connected to the mains
supply.
IMPORTANT: Installation must only be carried out by a qualified
professional or electrician.
At the back of your mirror is a length of 3 core cable which is
connected to the mirror. After fitting the fuse spur which will be
used to connect the mirror to the mains, identify the EARTH
NEUTRAL and LIVE wires in both the spur and the mirror.
When connecting the cables, ensure that no connections are loose,
and that proper safety regulations have been followed. Leave
enough cable to make moving and hanging the mirror easier.
After connection, the mirror should be hung using the steps 4-7
above.
PRODUCT OVERVIEW
OPERATION
When the mirror is connected and hung securely
onto the wall, turn the mains power back on and the
mirror will be ready to use.
To operate, use the touch button on the front of the
mirror, it is located at the bottom. Touch the button
gently to turn on, and press again to switch off.
ON/ OFF TOUCH
BUTTON
LIGHT BAR
(BEHIND MIRROR)

8
TECHNICAL SPECIFICATION
Model
BeBa_24919
BeBa_27531
LxHxW (cm)
80x80x3.5
60x60x3.5
Net Weight (Kg)
6.65
4
Power Cord length (cm)
68.5
45
Rated Power
36 W
26 W
IP Rating
IP 44
IP 44
Input
220 V - 240 V 50 Hz
220 V - 240 V 50 Hz
This product contains a light source of energy efficiency class F.
DISPOSAL
Recycling facilities are now available for all customers at which you can
deposit your old electrical products. Customers will be able to take any old
electrical equipment to participating sites run by their local councils.
Please remember that this equipment will be further handled during the
recycling process, so please be considerate when depositing your
equipment. Please contact the local council for details of your local
household waste recycling centers.
At the time of printing the product contains no substances listed within Annex XIV of the
Reach Regulations (EC) 1907/2006. In accordance with Article 59 of the same regulation the
following substances are contained within the product at permitted levels: Cadmium.
As a responsible manufacturer the regulations are monitored to ensure continued
compliance. Further information can be provided upon request.