Better Bathrooms BeBa-24919 User manual

1
TOUCH CONTROL LED MIRROR
BeBa-24919
•TOUCH CONTROL
•LED LIGHT
•IP44 INGRESS PROTECTION

2
CONGRATULATIONS ON YOUR PURCHASE
Our aim at Better Bathrooms is to bring you extraordinary bathroom products,
for less.
If you’re after a modern, traditional, or a totally unique style bathroom, we
have the fittings and fixtures to bring your ideas to life, so you can fall in love
with your space every day.
We hope you’re happy with your new product. But if you experience any
problems, we’re always here to help.
•Call our friendly UK call centre on 0330 390 3062
(Lines open 9am-4.30pm Monday to Friday, or 9am-2pm Saturday).
•Send us a message via betterbathrooms.com.
PRODUCT OVERVIEW
ON/ OFF TOUCH
BUTTON
LIGHT BAR
(BEHIND MIRROR)

3
SAFETY
•This mirror should be installed by a qualified electrician.
•This fitting is only suitable for connection to a 220-240V earthed supply
in accordance with current IEE wiring regulations, and should be installed
in accordance with local Building Regulations.
•This is for domestic, indoor use only.
•The fitting should be connected to a dedicated lighting circuit which
must be protected by a 5-amp fuse (or a 6 amp miniature circuit
breaker).
•The electrical connection must be an adequate distance from the rear of
the mirror to prevent the risk of shorting with the mirror’s casing.
•Before installing the fitting ensure that the mains supply is switched off,
and that the appropriate fuse is removed (or appropriate circuit breaker
is switched off) before commencing installation. Ensure that measures
are taken to prevent the supply from being inadvertently reconnected.
•If there is a “Minimum Distance” label, please do not allow flammable
materials to rest within that distance from the unit.
•This product may contain delicate parts –be careful during handling and
maintenance to avoid breakage.
•If any modification is made to the fitting it will invalidate the warranty
and may render the product unsafe.
•A defective appliance may cause electric shock. Never switch on a
defective or damaged appliance. Disconnect the appliance from the
mains before seeking assistance.
•This product is IP44 rated, and no part of the installation is allowed to be
within bathroom Zones 0 or 1. Installation is permitted within Zone 2.
•This product must be earthed. Before commencing installation, ensure
that there are no pipes or wires located behind the wall that may be
damaged during drilling.
•Ensure that the hanging location has been decided upon and marked
clearly to avoid unwanted damage to the wall due to incorrect
positioning.
•Inspect the mirror to ensure there are no signs of damage prior to
installation.
•Take care unpacking, do not use a sharp blade to open as this may
damage the mirror and void your warranty.
•Once installed a bead of silicon can be applied between the mirror and
the wall around the unit. Never seal the bottom of the mirror to the wall,
as this may allow water to accumulate behind the mirror.

4
BATHROOM ZONES
Zone 0:
The interior of the bathtub or shower basin.
Zone 1:
The area around the bathtub or shower basin up
to a height of 2.25m above the floor
Zone 2:
The area stretching to 0.6m outside the bath or
shower and above the bath or shower if over
2.25m

5
INSTALLATION
IMPORTANT: Before commencing installation, ensure that there are no pipes
or wires located behind the wall that you will be drilling into.
•Ensure that the hanging location has been decided upon and marked clearly
to avoid unwanted damage in the wall due to incorrect positioning.
•Check there the mirror is not damaged prior to installation.
•Take care unpacking, do not use a sharp blade to open as this may damage
the mirror and void your warranty.
At the back of the mirror, there are 2 hanging hooks
spaced across the top. To hang the mirror, two holes are
required in the wall. Before drilling, ensure that no wires
or pipes are behind the wall. If unsure, seek professional
advice.
1. Measure the distance between the centre of the two hanging points.
2. Make a note of the distance and mark their position on the wall. Use a
spirit level to ensure that the marks are level.
3. Drill the 2 holes into the wall at the position marked using a suitable drill
bit.
4. Insert the wall plugs into the holes.
5. Insert the screws into the wall plugs, ensuring their heads are protruding
by approximately 3mm.
6. Check to ensure the screws line up correctly and the mirror can be safely
hung from them.
7. Carefully lower the mirror onto the 2 screws, ensuring that is secure and
will not slide.

6
CONNECTING THE MIRROR
To connect your mirror, it must be first be connected to the mains
supply.
IMPORTANT: Installation must only be carried out by a qualified
professional or electrician.
At the back of your mirror is a length of 3 core cable which is
connected to the mirror. After fitting the fuse spur which will be
used to connect the mirror to the mains, identify the EARTH
NEUTRAL and LIVE wires in both the spur and the mirror.
When connecting the cables, ensure that no connections are lose,
and that proper safety regulations have been followed. Leave
enough cable to make moving and hanging the mirror easier.
After connection, the mirror should be hung using the steps 4-5 in
the “HANGING THE MIRROR SECTION”.
OPERATION
When the mirror is connected and hung
securely onto the wall, turn the mains power
back on and the mirror will be ready to use.
To operate, use the touch button on the front
of the mirror, it is located at the bottom.
Touch the button gently to turn on, and press
again to switch off.

7
TECHNICAL SPECIFICATION
Model
BeBa-24919
LxHxW (cm)
80x80x3.5
Net Weight (Kg)
6.65
Power Cord length (cm)
68.5
Rated Power
44 W
IP Rating
IP44
Input
220 V - 240 V 50 Hz
DISPOSAL
Recycling facilities are now available for all customers
at which you can deposit your old electrical products.
Customers will be able to take any old electrical
equipment to participating sites run by their local
councils. Please remember that this equipment will be
further handled during the recycling process, so
please be considerate when depositing your
equipment. Please contact the local council for details of your local
household waste recycling centers.