BGS technic 62614 User manual

SW-Stahl und Werkzeugvertriebs GmbH Tel. [phone] / 46438-0
F56essartSresukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D
Instruction Manual
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[email protected]
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
Art. 62614
Engine Timing Tool Set BMW N40 / N45
GENERAL INFORMATION
This engine timing kit contains the tools required for engine timing control and setting in the case of
timing chain replacement, cylinder head repair, cylinder head gasket replacement, etc. and is suitable
for the indicated BMW cars / engines with timing chain.
SAFETY INSTRUCTIONS
xDo not use the tools with any of the parts missing of damaged.
xNever place tools on the car battery. Risk of electrical short.
xBe careful while working on running engines. Loose clothing, tools and other objects may get
caught in revolving parts and cause severe personal injuries.
xKeep away children and other unauthorized persons from the working area.
xBe careful while working on hot engines – risk of burns!
xRemove the ignition key before starting your repair work in order to avoid unintentional starting of
the engine and the consequential engine damage.
xThese instructions are intended as an overview and can by no means substitute a workshop
manual.
xAlways use car-specific service manuals to look up technical data such as torque values,
disassembly/assembly instructions, etc.
xAfter repair or before starting the engine, respectively, rotate the engine twice by hand and
recheck engine timing.
xDo not use any detergents to clean timing belt, sprockets or pulleys
xOnly rotate the engine in its normal direction of rotation (clockwise unless stated otherwise)
LIST OF CARS
Model Series Engine Engine Code
116 E81/ E87 1.6L
316 E46 / E90 1.6L
316 E46 1.6 Ci
316 E46 1.6 ti
N40
N45
N45T (B16)
1
23
4 5
6

SW-Stahl und Werkzeugvertriebs GmbH Tel. [phone] / 46438-0
F56essartSresukreveL ax +49 (0) 2191 / 46438-40
ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D
Instruction Manual
BGS technic KG
Bandwirkerstr. 3
42929 Wermelskirchen
Tel.: [phone]
Fax.: [phone]
[email protected]
www.bgstechnic.com
© BGS technic KG, Copying and further use not allowed
TOOLS
Nr. Denomination to be used as OEM
1rotary sensor fixing tool OEM 117260
2camshaft setting tool (outlet) OEM 117251
3camshaft setting tool (inlet) OEM 117252
4timing chain pretensioning tool OEM 119340
5crankshaft setting pin OEM 119190
6connecting bolt OEM 117253
APPLICATION
Crankshaft setting pin
for setting the crankshaft to TDC position.
The bore hole dedicated to this purpose is located on the
inlet side below the starter.
Inlet camshaft setting tool
for setting the inlet camshaft
The correct setting has been reached, when the tool is
poised max. 0.5 mm above or resting on the cylinder
head without leaving a gap
Outlet camshaft setting tool with connecting bolt
for positioning the outlet camshaft
The correct setting has been reached, when the tool is
resting on the cylinder head without leaving a gap.
Timing chain pretensioning tool
for timing chain pretensioning after assembly.
Caution: please observe the manufacturer‘s torque
value. Pretensioning with a torque wrench is imperative.
Rotary sensor fixing tool
to fix the rotary sensors while tightening the rotary
sensor bolts.
Caution: the tool has to be screwed to the cylinder head
applying a torque of approx. 5 Nm before tightening the
rotary sensor bolts