BIOTRONIK Renamic User manual

Renamic
Medcal programmer and montorng devce
Quick Reference Guide
External Devices
Cardiac Rhythm Management

Telemetry status in 6 stages
(0 bars = 0% up to 5 bars = 100%)
Active function Patient name Device name and serial number
Heart rate
ECG monitor
(values derived from real-time IEGM)
Navigator with
navigation buttons
Forward/back navigation
ECG window
Button for exiting the follow-up
session. The start screen is displayed
and all interrogated data and test
results are stored.
Freeze function
(ECG snapshot of the last 60 sec.)
Help function (accessible from
any application window)
Button for enlarging/reducing
the ECG window
Function buttons (depending on
the current application window)
Application window
Display area for
status messages
Settings for the ECG display
Button for setting the gain
of the respective signal

( Inlet >< bndng )
7
1
2
3
4
5
6
8
13
12
11
10
9
14
15
16
18
19
20

21
22
23
24
27
26
25
28
29
31
30

1 Touch screen
2 Device body
3 USB ports
4 ECG port
5 Slot for expansion module
6 Screen release button (right)
7 Fixation for carrying strap (right)
8 Pen holder
9 PGH compartment lid release button
10 Printer buttons
11 Stylus in pen holder
12 Safe program button
13 Emergency shock button
14 Carrying handle
15 Fixation for carrying strap (left)
16 Screen release button (left)
18 Paper tray for internal printer
19 On/off button
20 Power cord port and device fuse
21 PGH port
22 USB slot with Bluetooth USB adapter
23 PGH cable and ECG cable
24 Cable feedthrough for PGH cable
25 On/off LED
26 Programming head (PGH)
27 PGH compartment lid
28 Anti-slip stand
29 Gripping tab
30 Power cord in power cord storage compartment
31 Power cord compartment lid

Navgaton
Summary of the most important
follow-up data.
All parameters displayed
in bold print can be selected.
Other application windows are
opened on selection.
Change the programmable
parameters of the implanted device.
Display the signals
recorded by the implanted device.
Perform tests
(e.g. threshold test).
Display all interrogated
implanted device statistics.
Summary of the status of
the implanted device.
Open the patient data in the
[Parameters] application window.
Open the list of recently recorded
signals in the [Recordings]
application window.
Open the corresponding test in the
[Tests] application window. Adapt the basic settings for
individual configuration.
Print manager
(list of all stored printing data).

( Inlet >< bndng )
Button for switching off the device in the user interface.
On/off button on the device
The on/off button (19) is located on the back left side of the device.
To switch on the device:
• Press the on/off button (19) once to the pressure point.
The on/off LED (25) on the front left side of the device lights up.
To switch off the device:
• Press the on/off button (19) once to the pressure point
or
• Shut down the device via the user interface.
Note:
If the power supply to Renamic is interrupted, the device will require approximately
60 seconds to restart once the power supply is reconnected.
If the power supply to Renamic is not interrupted and the device is switched off using the
button on the screen or the on/off button on the device (19), then the device will require
approximately 30 seconds to restart.
Switching the device on and off

Freeze/Prnt
Freeze function (ECG/IEGM recording)
Renamic constantly stores the last 60 seconds of the real-time signals (IEGM, ECG and markers) displayed in the ECG window.
The Freeze function can be used to pause the signal display in order to analyze events that have occurred within the last 60 seconds.
Key below the ECG area to open the
[Freeze] button.
(1) (2)
Display of the IEGM amplitude (A, RV, LV) at the position of
the left caliper (1) and the right caliper (2)
Keys for precise placement of the caliper lines. The calipers can also be positioned
on the ECG display itself (select, hold and drag).
Circle function to check constant distances between several events
Button for saving as a file in the follow-up data of the print and data
manager tabs with the designation "Freeze".
Selection to print or store the entire length of 60 seconds, only
the window contents, or the section between the caliper lines.
Button for printing the displayed recording section. The recording is
simultaneously stored as a file in the follow-up data of the print and data
manager tabs with the designation "Freeze".

Printing during follow-up
List of available data for
activated follow-up.
List of all stored follow-ups for the
implanted device being interrogated.
The activated follow-up is
highlighted in blue.
The current follow-up session is
selected by default.
Check box for selecting or deselecting
the follow-up data to be printed.
The [Print] button is available in every application window for immediate printing. All data
interrogated and produced during follow-up are automatically stored and can be displayed in the
Print manager tab at any time using the [More] button.
Keys for selecting the print profiles.
The check boxes for available data are
adapted to the respective profile.

Printing and exporting stored data
Select the [Data manager] button on the start screen. All stored follow-up data can be viewed, printed, exported and sorted according to the displayed
columns. Lines containing the same information in the sorted column are summarized. For example, if the follow-up data is sorted according to the "Patient"
column, then all follow-up data for a single patient will be summarized. However, if the "Date" column is selected for sorting, then all follow-up data will be
summarized for the same date but with various different patients.
Use the arrows to expand
or collapse the summarized
follow-up data.
Select a column header to sort and
summarize the follow-up data.
Export follow-up data that has been
selected using the check boxes.
Import follow-up data in
BIOTRONIK backup format.
Export the selected follow-up data in
Adobe PDF format.
Data export settings.
Edit the patient name
selected with a check box.
Export