Biral T2 S User manual

ModulA… RED, ModulA-D… RED
ModulA… GREEN
ModulA… BLUE
T2 S
Installation and Operating Instructions (Page 6)
Montage- en bedrijfsinstructies (Pagina 37)
Instrucciones de montaje y funcionamiento (Página 68)

2
EN EU Declaration ofConformity
We Biral AG declare under our sole responsibility that the
products
ModulA… RED, ModulA-D… RED
ModulA…GREEN
ModulA… BLUE
to which this declaration relates, are in conformity with the
Council Directives on the approximation of the laws of the EC
Member States relating to:
– Machinery (2006/42/EG) Standard: 12100-1:2010
–Electrical equipment designed for use within certain
voltage limits (2014/35/EU) Norms: EN 60335-1:2012,
EN 60335-2-51:2003 + A1:2008 + A2:2012
–Electromagnetic compatibility (2014/30/EU) Norms: EN
61000-6-2:2005, EN 61000-6-3:2007
– Only for types marked with the EEI. (See the pump
nameplate):
Ecodesign (2009/125/EC) Circulator Pumps Commis-
sion Regulation No 641/2009 Standards: EN 16297-
1:2012, EN16297-2:2012
EN-UK UK Declaration of Conformity
We Biral AG declare under our sole responsibility that the
products
ModulA… RED, ModulA-D… RED
ModulA…GREEN
ModulA… BLUE
to which this declaration relates, are in conformity with the
Council Directives on the approximation of the laws of the UK
Member States relating to:
– UK S.I. 2008/1597 Supply of Machinery (Safety)
Regulation 2008.
–Electrical equipment designed for use within certain
voltage limits (2014/35/EU) Norms: EN 60335-1:2012,
EN 60335-2-51:2003 + A1:2008 + A2:2012
–UK S.I. 2016/1091 Elektromagnetic compatibility
Regulation 2016
Norms: EN 61000-6-2:2005, EN 61000-6-3:2007
– Only for types marked with the EEI. (See the pump
nameplate):
Ecodesign (2009/125/EC) Circulator Pumps Commis-
sion Regulation No 641/2009 Standards: EN 16297-
1:2012, EN16297-2:2012
NL EG-conformiteitverklaring
Wij Biral AG verklaren geheel onder eigen verantwoorde-
lijkheid dat de produkten
ModulA… RED, ModulA-D… RED
ModulA…GREEN
ModulA… BLUE
waarop deze verklaring betrekking heeft in overeenstem-
ming zijn met de Richtlijnen van de Raad inzake de onder-
linge aanpassing van de wetgevingen van de EG Lid-Sta-
ten betreffende
– Machines (2006/42/EG) Norm: EN 12100-1:2010
– Elektrisch materiaal voor gebruik binnen bepaalde
spanningsgrenzen (2014/35/EU) Normen: EN 60335-
1:2012, EN 60335-2-51:2003 + A1:2008 + A2:2012
–Elektromagnetische compatibiliteit (2014/30/EU) nor-
men: EN 61000-6-2:2005, EN 61000-6-3:2007
–Ecodesign (2009/125/EC)
Circulatiepompen: Verordening nr. 641/2009 van de
Commissie. Normen: EN 16297-1:2012, EN 16297-
2:2012 (geldt alleen voor types die met de ETI zijn
gemarkeerd. EEI staat voor Energy Efficiency Index, zie
bedrijfsnaamplaatje).
Münsingen, 1st November 2022
Roger Steuri
Head of Product Development/Management
Person authorised to compile technical file
and empowered to sign the EC declaration of
conformity.
ES Declaración de conformidad CE
Nosotros Biral AG declaramos bajo nuestra única respon-
sabilidad que los productos
ModulA… RED, ModulA-D… RED
ModulA…GREEN
ModulA… BLUE
son conformes con las Directivas del Consejo relativas a la
aproximación de las legislaciones de los Estados Miembros
de la CE sobre
–Máquinas (2006/42/CE)
Norma: EN 12100-1: 20101
– Material eléctrico destinado a utilizarse
con determinadas límites de tensión (2014/35/EU)
Normas: EN 60335-1:2012, EN 60335-2-51:2003 +
A1:2008 + A2:2012
–Compatibilidad electromagnética (2014/30/EU)
Normas: EN 61000-6-2:2005, EN 61000-6-3:2007
–Unicamente a las circuladoras marcadas con el EEI.
(Véase la placa de caracteristicas):
Diseno ecológico (2009/125/EC)
Bombas circuladoras: Reglamento de la Comisión
no 641/2009. Normas: EN 16297-1:2012, EN16297-
2:2012
Biral AG
Südstrasse 10
CH-3110 Münsingen
Phone [phone]
Fax [phone]
[email protected]
www.biral.ch

3
Dimensions
Afmetingen
Dimensiones
Series
Serie
Series
130
112.8
80
70
80
G
L
186.252
238.2
70
961797_00
0.4
N5
0.8
N6
1.6
N7
3.2
N8
6.3
N9 N10 Rauheitsklassen
12.5 Rauhwerte Ra
ts
ts
ts
17.10.2014
17.10.2014
00
1
0.5 bis 6
± 0.1
über 120 bis 400
± 0.5
über 30 bis 120
± 0.3
über 6 bis 30
± 0.2
über 400 bis 1000
± 0.8
TD-0028180 PDM_Nr
13.10.2014 gezeichnet
geprüft
Freigabe
Änd.Index
961797
Ersatz für: Ersetzt durch:
Bemerkung Material
Modell/Art.Nr
Visum Änd.Index
Gegenstand
Datum
II I
Stück
Pos
1:3
Zeichnungsnummer
Massstab
Biral AG
CH-3110 Münsingen
DN25, DN32 für BA
ModulA 25-, 32- 180 RED, BLUE
Massbild
Allgemeintoleranzen ISO 2768-mK
ModulA… RED
ModulA… BLUE
25-4 180
PN 6/10
25-6 180
PN 6/10
25-8 180
PN6/10
25 -10 180
PN 6/10
25 -12 180
PN 6/10
32-4 170
PN 6/10
32-6 170
PN 6/10
32-8 170
PN 6/10
32-10 170
PN 6/10
DN 25 25 25 25 25 32 32 32 32
L180 180 180 180 180 170 170 170 170
G1 ½“ 1 ½“ 1 ½“ 1 ½“ 1 ½“ 2“ 2“ 2“ 2“
kg (RED) 4.5 4.5 4.5 4.5 4.5 4.7 4.7 4.7 4.7
kg (GREEN) 4.5 4.5 4.5 4.5 4.5 4.7 4.7 4.7 4.7
kg (BLUE) 4.8 4.8 4.8 4.8 4.8 5 5 5 5
32-12 170
PN 6/10
32-4 180
PN 6/10
32-6 180
PN 6/10
32-8 180
PN 6/10
32-10 180
PN 6/10
32-12 180
PN 6/10
DN 32 32 32 32 32 32
L170 180 180 180 180 180
G2“ 2“ 2“ 2“ 2“ 2“
kg (RED) 4.7 4.7 4.7 4.7 4.7 4.7
kg (BLUE) 5 5 5 5 5 5

4
Dimensions
Afmetingen
Dimensiones
Series
Serie
Series
ModulA-D… RED
32-6 180
PN 6/10
32-8 180
PN 6/10
32-12 180
PN 6/10
DN
32 32 32
L
180 180 180
G
2“ 2“ 2“
kg (RED)
11.1 11.1 11.1
100
65
130 80
110 110 112.870
402.8
G
L
18454
238
961799_00
65
0.4
N5
0.8
N6
1.6
N7
3.2
N8
6.3
N9 N10 Rauheitsklassen
12.5 Rauhwerte Ra
ts
ts
ts
17.10.2014
17.10.2014
00
1
0.5 bis 6
± 0.1
über 120 bis 400
± 0.5
über 30 bis 120
± 0.3
über 6 bis 30
± 0.2
über 400 bis 1000
± 0.8
TD-0028184 PDM_Nr
14.10.2014 gezeichnet
geprüft
Freigabe
Änd.Index
961799
Ersatz für: Ersetzt durch:
Bemerkung Material
Modell/Art.Nr
Visum Änd.Index
Gegenstand
Datum
II I
Stück
Pos
1:3.8
Zeichnungsnummer
Massstab
Biral AG
CH-3110 Münsingen
DN 32x180 für BA
ModulA-D 32 RED
Massbild
Allgemeintoleranzen ISO 2768-mK
Dimensions
Afmetingen
Dimensiones
Series
Serie
Series
ModulA-D… RED
32F-6 220
PN 6
40-6 220
PN 6-16
DN 32F 40
L1 220 220
L2 120 120
L3 85 105
B1 403 454
B2 70 81
B3 110 130
B4 113 113
D120 150
k1 (PN 6) 70 100
k2 (PN10 / 16) – 110
d4x14 4x14/19
T1 60 277
T2 184 79
T3 244 198
kg (RED) 13.4 18.7
B1
130 80
L2
L3
B3 B3 B4B2
L1
T3T2
T1
961800_00
65
250
k1
k2
DN
D
d
PN 6-16
0.4
N5
0.8
N6
1.6
N7
3.2
N8
6.3
N9 N10 Rauheitsklassen
12.5 Rauhwerte Ra
ts
ts
ts
17.10.2014
17.10.2014
00
1
0.5 bis 6
± 0.1
über 120 bis 400
± 0.5
über 30 bis 120
± 0.3
über 6 bis 30
± 0.2
über 400 bis 1000
± 0.8
TD-0028186 PDM_Nr
14.10.2014 gezeichnet
geprüft
Freigabe
Änd.Index
961800
Ersatz für: Ersetzt durch:
Bemerkung Material
Modell/Art.Nr
Visum Änd.Index
Gegenstand
Datum
II I
Stück
Pos
1:4.5
Zeichnungsnummer
Massstab
Biral AG
CH-3110 Münsingen
DN32F, DN40 für BA
ModulA-D 32F, 40...RED
Massbild
Allgemeintoleranzen ISO 2768-mK

5
Dimensions
Afmetingen
Dimensiones
Series
Serie
Series
130
112.870
80
G
L
186.252
238.2
IL00006764_00
PDM_Nr:
Erstelldatum
Dokumentstatus:
1:3
Massstab
Format:
A3
CH-3110 Münsingen
Biral AG
Werkstoff:
Massbild
DN25, DN32 für BA
18.11.2021 sta
18.11.2021 sta
211645
Freigegeben
IL00006764
Zeichnungsnummer
A
Vers.
Änd. Ind.
Rev.
00
ModulA 25-, 32- 180 GREEN T2S
ModulA... GREEN
25-4 180
PN 6/10
25-6 180
PN 6/10
25-8 180
PN6/10
25 -10 180
PN 6/10
25 -12 180
PN 6/10
32-4 170
PN 6/10
32-6 170
PN 6/10
32-8 170
PN 6/10
32-10 170
PN 6/10
DN 25 25 25 25 25 32 32 32 32
L180 180 180 180 180 170 170 170 170
G1 ½“ 1 ½“ 1 ½“ 1 ½“ 1 ½“ 2“ 2“ 2“ 2“
kg (RED) 4.5 4.5 4.5 4.5 4.5 4.7 4.7 4.7 4.7
kg (GREEN) 4.5 4.5 4.5 4.5 4.5 4.7 4.7 4.7 4.7
kg (BLUE) 4.8 4.8 4.8 4.8 4.8 5 5 5 5
32-12 170
PN 6/10
32-4 180
PN 6/10
32-6 180
PN 6/10
32-8 180
PN 6/10
32-10 180
PN 6/10
32-12 180
PN 6/10
DN 32 32 32 32 32 32
L170 180 180 180 180 180
G2“ 2“ 2“ 2“ 2“ 2“
kg (GREEN) 4.7 4.7 4.7 4.7 4.7 4.7
Dimensions
Afmetingen
Dimensiones
Series
Serie
Series
130
11370
80
T1
L
T3T2
IL00006765_00
k2
d
D
k1
DN
PDM_Nr:
Erstelldatum
Dokumentstatus:
1:3.2
Massstab
Format:
A3
CH-3110 Münsingen
Biral AG
Werkstoff:
Massbild
DN32F, DN40, DN50 BG2
18.11.2021 sta
18.11.2021 sta
211647
Freigegeben
IL00006765
Zeichnungsnummer
A
Vers.
Änd. Ind.
Rev.
00
ModulA 32F-,40-,50- GREEN T2S
ModulA... GREEN
32F-6 220
PN 6
40-4 220
PN 6-16
40-6 220
PN 6-16
40-11 250
PN 6-16
50-11 220
PN 6-16
DN 32F 40 40 40 50
L220 220 220 250 220
D120 150 150 150 148
k1 (PN 6) 90 100 100 100 110
k2 (PN10 / 16) – 110 110 110 125
d14 4x 14/19 4x14/ 19 4x14/ 19 4x14/ 19
T1 246 263 263 249 255
T2 52 61 61 54 54
T3 186 198 198 184 184
T4 85 88 88 85 85
kg (GREEN) 7 9.2 9.2 – 8.8

6| english
Contents
1 Safety information..............................7
1.1 General remarks ....................................7
1.2 Identification of notices ..........................7
1.3 Staff qualification and training................7
1.4 Risks in the event of non-compliance
with the safety information.....................7
1.5 Safety-conscious work ..........................7
1.6 Safety information for the operator /
operating personnel...............................8
1.7 Safety information for installation,
maintenance and inspection works .......8
1.8 Unauthorised reconstruction and
production of spares..............................8
1.9 Improper operating methods.................8
2 Symbols used......................................8
3 General information...........................9
3.1 Purpose.................................................9
3.2 Requirements of the delivery medium....9
3.3 Operating conditions ........................... 11
3.4 Non-return valve .................................. 11
3.5 Protection from the effects of frost....... 11
3.6 Heat insulation (ModulA... RED, Modu-
lA... BLUE)............................................12
3.7 Heat insulation (ModulA... GREEN) ......12
3.8 Flow direction ......................................12
4 Installation.........................................13
4.1 General notes ......................................13
4.2 Flushing heating equipment (for exten-
ded pump) ...........................................13
4.3 Installation............................................13
4.4 Permissible installation positions .........13
4.4.1 Rotate the pump head.........................15
4.5 Install the pump in the unit...................15
4.5.1 Flange connection ...............................16
5 Electrical connection.......................17
5.1 Additional safety features.....................17
5.2 Supply voltage..................................... 17
5.3 Connection of the power supply..........18
5.4 Connecting Biral Connector ...............19
5.5 Connection drawing Clamp
description...........................................19
5.6 Switch settings ....................................20
5.6.1 Switch 1, Fault or operating signal
(switchable)..........................................20
5.6.2 Switch 2, external OFF or
external ON (switchable)......................21
5.6.3 Switch 3, power limit
(can be activated).................................21
6 Start-up..............................................22
6.1 General................................................22
6.2 Operational control ..............................22
7 Settings..............................................22
7.1 Control panel .......................................22
7.2 Types of control ...................................23
7.3 Delivery height (A2)..............................23
7.4 Display of the current delivery height
(LED V
• )................................................24
7.5 Summary of maximum delivery height
and delivery amount ............................24
7.6 Activating/deactivating the control
keys .....................................................24
7.7 START / STOP pump ............................24
7.8 Activate/deactivate dry running
detection..............................................25
7.9 Bluetooth (Biral ONE.) ..........................26
7.9.1 Activate Bluetooth................................26
7.9.2 Open Biral ONE. ..................................26
7.9.3 Extract Biral ONE.................................26
7.10 Biral impeller ........................................27
7.11 On-site adjustment of the pump ..........27
8 Fault summary and checklist .........28
9 Sensor...............................................30
10 Accessories/ versions .....................30
10.1 Biral interface module, BIM B3 ............30
10.2 Blind flange..........................................30
11 Technical data...................................31
12 Recycling...........................................32
13 Spare parts list .................................33
13.1 ModulA... RED, ModulA... BLUE ..........33
13.2 ModulA... GREEN ................................35

english
|
7
1 Safety information
Warning
This product may only be installed and used by people who have adequate knowled-
ge and experience. People with limitations in their physical or mental capacity or
sensory perception, may not use the product, unless they have been sufficiently
trained by a person who is responsible for their safety.
The product must be kept out of the reach of children. The product must not be used
by children, e.g. as a toy.
1.1 General remarks
These installation and operating instructions contain items of information of fundamental
importance which must be taken into account during assembly, operation and maintenance. They
should therefore be read without fail before installation and commissioning by the fitter and also the
responsible specialist staff/operator. They must always be available for consultation at the plant’s
place of deployment. Not only are the general safety hints included in this «Safety Hints» section to
be observed, but also the special items of safety information included in the other sections.
1.2 Identification of notices
Information signs mounted directly on the plant, such as, for example
– rotating direction arrow
– symbols for fluid connections
must be obeyed without fail and be kept in a fully legible state.
1.3 Staff qualification and training
The staff deployed for assembly, operating, maintenance and inspection tasks must show that
they have the appropriate qualifications for such work. The field of responsibility, competence and
supervision of the staff must be stipulated exactly by the operator.
1.4 Risks in the event of non-compliance with the safety information
Non-compliance with the safety information can result in both danger for persons and also for
the plant and the environment. Non-compliance with the safety information can lead to the loss of
claims for damages of any kind. In detail, non-compliance, for example, may result
in the following risks:
– failure of important functions in the plant
– failure of prescribed methods for servicing and maintenance
– danger to persons through electrical and mechanical causes
1.5 Safety-conscious work
The safety information contained in these installation and operating instructions, the existing national
regulations for the prevention of accidents, as well as any internal working, operating and safety
regulations stipulated by the operator must be observed.

8| english
1.6 Safety information for the operator/operating personnel
Any risks from electric power must be eliminated (For details see, for example, the regulations pub-
lished by NIN (CENELEC) and the I.E.E.).
1.7 Safety information for installation, maintenance and inspection works
The operator has to ensure that all installation, maintenance and inspection works are carried out
by authorised and qualified specialist personnel who have informed themselves adequately about
the requirements by a thorough study of the installation and operating instructions.
Basically, any works on the plant should only be carried out when it is at a standstill and not carrying
any electrical current. Directly after completion of the works, all safety and protective installations
must be mounted or activated again.
Before re-commissioning, the points listed in the section «Electrical connection» must be observed.
1.8 Unauthorised reconstruction and production of spares
Reconstruction of or changes to pumps are only permissible after consultation with the manufactur-
er. Genuine spare parts and accessories authorised by the manufacturer serve the cause of safety.
The use of other parts can cancel any liability for the resultant consequences of this.
1.9 Improper operating methods
The operating reliability of the pumps supplied is only guaranteed with appropriate application of
the section «Intended application» of the Installation and Operating Instructions. The limit values
given in the technical data must not be exceeded on any account.
2 Symbols used
Warning
Serious personal injury may result from not adhering to these safety notes.
Warning
Danger from dangerous electrical voltage.
If these safety instructions are not adhered to, there is a risk of electric shock, which
may lead to serious injury or death .
Warning
Risk of injury or burns from hot surfaces!
Warning
Risk of injury from falling objects!

english
|
9
Warning
Risk of injury from escaping steam!
Not adhering to these safety notes may cause malfunctioning or material damage.
This contains advice or notes that facilitate work and ensure safe operation.
3 General information
The Biral series, ModulA consists of a complete range of circulation pumps with integrated frequen-
cy converter, which enable independent or controlled adaptation of output to the actual require-
ment of each system. Therefore, in many systems, energy consumption will be reduced and the
control behaviour of the system improved. Besides this, current noise from control cabinets can be
reduced effectively. All necessary settings can be adjusted using the control panel for the pump.
3.1 Purpose
Biral circulation pumps of the ModulA series are intended for the circulation of liquids in the follow-
ing systems:
– ModulA... RED in heating units
– ModulA... GREEN in air-conditioning units and cooling systems
– ModulA... BLUE in domestic hot water systems
The pumps can also be used in the following systems:
– Geothermal heat pumps
– Thermal solar equipment
The pumps are suitable for use in systems with variable and constant delivery volumes.
3.2 Requirements of the delivery medium
The pump is suitable for delivery of pure, thin, non-explosive and non-aggressive media without
fixed or long-fibred elements, which do not affect the pump either mechanically or chemically.
Heating water:
Requirements according to current standards that apply to water quality in heating systems: (e.g.
VDI 2035)

10 | english
Glykol:
The pump can be used for delivering water-glycol mixes. Maximum permissible viscosity: 50 mm²/s
(cSt). This corresponds to a water-ethylene-glycol mix with a glycol content of around 50% at –10°C.
The pump is controlled via an output-limiting function that protects against overload. The delivery
of glycol mixes affects the MAX characteristic curve because the delivery capacity is reduced
accordingly, based on the glycol content and temperature of the media. So that the effect of the
glycol is not reduced, temperatures above the nominal temperature given for the medium should
be avoided. Generally, the operating duration with high media temperatures should be minimised.
Before adding the glycol mix, it is vital that the system is cleaned and rinsed. To avoid corrosion or
precipitations, the glycol mix should be checked regularly and changed if necessary. If the glycol
mix has to be further thinned, the specifications from the glycol manufacturer should be adhered to.
For the delivery of a liquid with density that differs from water and/or kinematic
viscosity, the delivery output is reduced.
Domestic hot water:
Permissible water hardness:
max. 35 °fH (20 °dH) (water temperature below 65 °C)
max. 25 °fH (14 °dH) (water temperature below 85 °C)
To counter the risk of lime deposits, for domestic hot water systems we recommend:
Hardness level max. 25 °fH (14 °dH) Medium temperature <65 °C
Warning
The pump may not be used to deliver combustible media such as diesel and fuel.
Warning
The pump may not be used to deliver aggressive liquids such as acids or seawa-
ter.

english
|
11
3.3 Operating conditions
Medium temperature:
– ModulA... RED +15 °C to +110 °C
– ModulA... GREEN +10 °C to +110 °C
– ModulA... BLUE +15 °C to +85 °C (recommended for domestic hot water systems: max 65 °C)
Operating pressure:
The maximum permissible operating pressure is indicated on the nameplate. (6 bar, 10 bar or 16
bar) Minimum operating pressure at the pump intake ports (intake pressure) at 500 m above sea
level:
Medium temperature
75 °C 95 °C 110 °C
ModulA … Supply pressure [bar]
25-4/6/8/10/12 0.1 0.35 1.0
32-4/6/8/10/12 0.1 0.35 1.0
40 - 4/6/11 0.1 0.35 1.0
50 -11 0.1 0.50 1.0
Per ±100 m height ± 0.01 bar
In the dual pump operation the supply pressure required must be increased by 0.1 bar in line with
the values in the table.
Ambient temperature:
0 °C to 40 °C
3.4 Non-return valve
961864_00
Einbau Rückschlagventil
ModulA
Schema
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum
Änd.Index
Visum
Ersetzt durch:
Ersatz für:
961864
Änd.Index
Freigabe geprüft gezeichnet
10.12.2014
PDM_Nr
TD-0028807
00
10.12.2014 10.12.2014
nma nma nma
If a non-return valve is fitted, the pump must be
adjusted (see 7.2), so that the discharge pres-
sure of the pump exceeds the closing pressure
of the valve at all times.
This must be adhered to in particular for the
proportional pressure control (reduced delivery
height for decreasing delivery flow).
3.5 Protection from the effects of frost
Where there is a risk of frost during downtime periods, measures required to avoid
frost damage must be taken.

12 | english
3.6 Heat insulation (ModulA... RED, ModulA... BLUE)
Heat is lost via the pump casing and pipes. These heat losses should be limited to
a minimum.
961604_00
WD
ModulA
für BA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:5
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961604
Änd.Index
Freigabe
geprüft
gezeichnet 19.03.2013
PDM_Nr TD-0021963
00
09.04.2013
09.04.2013
ts
ts
ts
Heat losses can be reduced by insulating the
pump casing and pipes.
For ModulA... RED and ModulA... BLUE, heat
insulation shells are included in the delivery.
Heat insulation shells can only be supplied for
single pumps
3.7 Heat insulation (ModulA... GREEN)
IL00002780_00
A
PDM_Nr:
Erstelldatum
Dokumentstatus:
1:2
Massstab
Format:
A4
CH-3110 Münsingen
Biral AG
Werkstoff:
Dämmung
DN 32-180
27.01.2020 sta
27.01.2020 sta
204004
Freigegeben
IL00002780
Zeichnungsnummer
A
Vers.
Änd. Ind.
Rev.
00
ModulA... GREEN (S)
1:2
The pump can be insulated together with the
pipe system.
Detail A
Keep the drainage outlet at the motor free.
Never cover the frequency
converter or the control panel
with insulation.
3.8 Flow direction
961572_00
Durschflussrichtung
ModulA
für BA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:5
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961572
Änd.Index
Freigabe
geprüft
gezeichnet 13.02.2013
PDM_Nr TD-0021575
00
09.04.2013
09.04.2013
ts
ts
ts
The arrow on the pump casing indicates the
flow direction.

english
|
13
4 Installation
4.1 General notes
ModulA is only intended for installation indoors. The pumps must be mounted voltage-free so that
no energy can be transferred from the pipes to the pump casing. The pumps can be installed di-
rectly in the pipe, provided the pipes are designed for the weight of the pump.
Installation is only possible after completion of all welding and soldering work on the system. Avoid
drops of water on the pump motor, especially the frequency converter.
Warning
The local regulations for the lifting and carrying
of loads must be adhered to. The weight of the pump is given on the packaging.
4.2 Flushing heating equipment (for extended pump)
To avoid unwanted interruptions to operations and non-running of the pump after longer
periods of inactivity, we recommend thoroughly flushing out the equipment following the
new installation or adaptation of heating and refilling.
The equipment must correspond with the latest technology. (Placement of expansion vessel
or safety flow).
4.3 Installation
Install only after completion of all welding or soldering work on the equipment. Water drops should
be avoided on the pump motor, especially on the electronics. The pump casing should be installed
voltage-free in the equipment.
4.4 Permissible installation positions
The installation position of the rotor shaft must always be horizontal.
961869_01
PDM_Nr:
Erstelldatum
Dokumentstatus:
1:2
Massstab
Format:
A3
CH-3110 Münsingen
Biral AG
Werkstoff:
Motor waagrecht
für BA
05.12.2019 sta
05.12.2019 sta
203246
Freigegeben
961869
Zeichnungsnummer
A
Vers.
Änd. Ind.
Rev.
01
ModulA BG2

14 | english
To guarantee adequate cooling, the frequency converter must always be in a horizontal position. (A,
B, C, D). It is delivered in position A.
AB
CD
E
I
M
J
F
N
G
K
O
H
L
P
961570_00
Montage Position
ModulA
für BA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:9
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961570
Änd.Index
Freigabe
geprüft
gezeichnet 04.10.2012
PDM_Nr TD-0020531
00
09.04.2013
09.04.2013
ts
ts
ts
Changing the installation position of the frequency converter
To ensure the correct installation position of the frequency converter, for installation positions E to
P (see 4.4) the pump head must be rotated 90°, 180° or 270°.
961592_01
PDM_Nr:
Erstelldatum
Dokumentstatus:
Massstab
Format:
A4
CH-3110 Münsingen
Biral AG
Werkstoff:
Achtung Sensorkabel
für BA
19.12.2019 sta
19.12.2019 sta
203658
Freigegeben
961592
Zeichnungsnummer
A
Vers.
Änd. Ind.
Rev.
01
ModulA bis 1600W
1:4
1
2
961581_01
PDM_Nr:
Erstelldatum
Dokumentstatus:
1:3
Massstab
Format:
A4
CH-3110 Münsingen
Biral AG
Werkstoff:
Sensorkabel ausstecken
für BA
05.12.2019 sta
05.12.2019 sta
203229
Freigegeben
961581
Zeichnungsnummer
A
Vers.
Änd. Ind.
Rev.
01
ModulA
1:3
The sensor cable must be separated from the frequency converter in advance!
Unplug the sensor cable
Unscrew the cable screws

english
|
15
4.4.1 Rotate the pump head
1
2
3
961801_00
Pumpenkopf drehen
ModulA BG2
DN32-180
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:2.3
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961801
Änd.Index
Freigabe
geprüft
gezeichnet 14.10.2014
PDM_Nr TD-0028189
00
17.10.2014
17.10.2014
ts
ts
ts
– Remove four hexagon socket screws
– Turn the pump head carefully in the desired
position without taking it off the pump casing.
(If the pump head is firmly connected with the
pump casing, loosen the pump head via light
blows from a rubber hammer.)
– Put in four inner hexagonal screws and tigh-
ten. (12Nm)
12Nm
961871_00
90°
3
21
O-Ring
Achtung Spaltring
ModulA BG2
für BA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:3.5
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961871
Änd.Index
Freigabe
geprüft
gezeichnet 16.12.2014
PDM_Nr TD-0028869
00
25.03.2015
25.03.2015
ts
nma
ts
If the motor is lifted off the pump casing, for
pump types
– ModulA 40-4 220, 40-6 220
– ModulA-D 40-6 220
care should be taken when replacing it due to
the moving ring, otherwise the running wheel
may be damaged.
Ensure correct positioning of the O-ring.
The ring in the pump casing must be centred
again before fitting the motor.
Fit the pump head carefully so that the mo-
tor lies flat on the pump casing without any
gaps.
Insert four hexagon socket bolts and tighten
the screws. (18Nm)
Warning
Do not drop the disassembled
pump parts!
4.5 Install the pump in the unit
2
961806_00
1
1
Pumpe mit Absperrschieber
ModulA 32
für BA Verschraubungspumpe
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:5
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961806
Änd.Index
Freigabe
geprüft
gezeichnet 16.10.2014
PDM_Nr TD-0026549
00
17.10.2014
17.10.2014
ts
ts
ts
– Close the shut-off valves and ensure that the
system is without pressure when fitting the
pump.
– Install the pump in the pipe with seals.
Warning
Risk of injury from escaping
steam!

16 | english
4.5 .1 Flange connection
The pump flanges are drilled with mounting holes, PN6/PN10/PN16. For safe screwing of the flang-
es, the shims supplied (B) must be fitted.
Safety elements (e.g. snap rings) are not permissible. For PN 10/16, special seals
and screws must be used.
Warning
Use the relevant screws for nominal pressure PN .
DN
961588_00
A
B
Pumpe mit Absperrschieber Bild2
ModulA
für BA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:5
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961588
Änd.Index
Freigabe
geprüft
gezeichnet 31.10.2012
PDM_Nr TD-0020748
00
15.02.2013
15.02.2013
ts
ts
ts
960573_00
M
Ø
Flansch PN6/10/16
für BA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:2
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
960573
Änd.Index
Freigabe
geprüft
gezeichnet 10.12.2014
PDM_Nr TD-0028815
00
10.12.2014
10.12.2014
nma
nma
nma
960573_00
M
Ø
Flansch PN6/10/16
für BA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:2
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
960573
Änd.Index
Freigabe
geprüft
gezeichnet 10.12.2014
PDM_Nr TD-0028815
00
10.12.2014
10.12.2014
nma
nma
nma
A B
PN 6 PN 10 /16 PN 6 PN 10/ 16
DN 32
M 12 M 16 Ø 14 Ø 18DN 40
DN 50
Recommended screw tightening torque:
– for M 12 <40 Nm
– for M 16 <95 Nm
Installation of combined flange with combined flange is not permissible.
961602_00
Pumpe mit WD
ModulA
für BA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:5
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961602
Änd.Index
Freigabe
geprüft
gezeichnet 09.04.2013
PDM_Nr TD-0022138
00
09.04.2013
09.04.2013
ts
ts
ts
After installation is completed, put on the heat
insulation shells and secure with cable bands.

english
|
17
5 Electrical connection
Electrical connection should be carried out in accordance with the local regulations.
It is vital to ensure that the voltage and frequency indicated on the nameplate are compatible
with the mains supply available.
Warning
Before carrying out any electrical connection work, the voltage supply must be
switched off.
The pump must be connected to an external network switch with a contact opening
on all poles of minimum 3 mm.
The protection against indirect contact can be achieved by earthing or potential
equalisation.
The pump does not require any external motor protection. The motor has integrated over-tempe-
rature protection, which offers safeguarding against overloading that appears slowly and against
blocking according to IEC 34-11: TP 211.
5.1 Additional safety features
If the pump is connected to an electrical installation, which has an FI circuit breaker for additional
protection, the FI circuit breaker must trigger with a pulsing direct current component if earthing
fault currents arise.
The FI circuit breaker must be marked with the following symbol:
Symbol Description
FI
1
2
N
L
L
N
961807_01
2 Externer Schalter
1 Sicherung (min.10A, träge)
Legende:
Netzanschluss 1x230V
ModulA
Alpha-Stecker BA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961807
Änd.Index
Freigabe
geprüft
gezeichnet 16.10.2014
PDM_Nr TD-0026642
01
24.02.2015
24.02.2015
ts
ts
ts
01 ts
24.02.2015
Highly sensitive residual current circuit breaker type A in
accordance with IEC 605
FI
1
2
N
L
L
N
961807_01
2 Externer Schalter
1 Sicherung (min.10A, träge)
Legende:
Netzanschluss 1x230V
ModulA
Alpha-Stecker BA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961807
Änd.Index
Freigabe
geprüft
gezeichnet 16.10.2014
PDM_Nr TD-0026642
01
24.02.2015
24.02.2015
ts
ts
ts
01 ts
24.02.2015
FI
1
2
N
L
L
N
961807_01
2 Externer Schalter
1 Sicherung (min.10A, träge)
Legende:
Netzanschluss 1x230V
ModulA
Alpha-Stecker BA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961807
Änd.Index
Freigabe
geprüft
gezeichnet 16.10.2014
PDM_Nr TD-0026642
01
24.02.2015
24.02.2015
ts
ts
ts
01 ts
24.02.2015
Highly sensitive residual current circuit breaker type B in
accordance with IEC 605
5.2 Supply voltage
1×230V ±10%, 50/60 Hz, PE
The voltage tolerances are set for equalising voltage fluctuations on the mains. They are not for
operating pumps with voltages other than those shown on the nameplate.
With direct mains connection, the pump may not be switched on and off at the
mains more than four times an hour. If the pump is switched on directly via the
mains, it only starts after a 5-second delay.

18 | english
5.3 Connection of the power supply
The pump must be protected on-site and must be connected to an external mains switch. All ca-
bles used must have a heat resistance of up to 85 °C. They must not be in contact with the pipe or
the pump and motor casing. All cables must be connected in accordance with EN 60204-1 and EN
50174-2: 2000. The electrical connection must be made as indicated on the nameplate.
ModulA… Nominal current [A] Output P1[W]
ModulA 25-4 180 0.08 – 0.37 7 – 49
ModulA 25-6 180 0.08 – 0.62 7 – 83
ModulA 25-8 180 0.08 – 0.85 7 – 115
ModulA 25-10 180 0.08 – 1.15 7 – 153
ModulA 25-12 180 0.08 – 1.36 7 – 181
ModulA 32-4 170 0.08 – 0.48 7 – 66
ModulA 32-6 170 0.08 – 0.73 7 – 102
ModulA 32-8 170 0.08 – 0.97 7 – 134
ModulA 32-10 170 0.08 – 1.25 7 – 169
ModulA 32-12 170 0.08 – 1.36 7 – 182
ModulA 32-4 180 0.08 – 0.48 7 – 66
ModulA 32-6 180, ModulA-D 32-6 180 0.08 – 0.73 7 – 102
ModulA 32-8 180, ModulA-D 32-8 180 0.08 – 0.97 7 – 134
ModulA 32-10 180 0.08 – 1.25 7 – 169
ModulA 32-12 180, ModulA-D 32-12 180 0.08 – 1.36 7 – 182
ModulA 32F-6 220, ModulA-D 32F-6 220 0.08 – 0.73 7 – 102
ModulA 40-4 220 0.08 – 0.74 11 – 97
ModulA 40-6 220, ModulA-D 40-6 220 0.08 – 1.47 11 – 185
ModulA 40-11 250 0.08 – 1.39 8 – 182
ModulA 50-11 220 0.08 – 1.39 8 – 182
Example of a typical mains connection, 1x230V ±10%, 50/60Hz
FI
1
2
N
L
L
N
961807_01
2 Externer Schalter
1 Sicherung (min.10A, träge)
Legende:
Netzanschluss 1x230V
ModulA
Alpha-Stecker BA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961807
Änd.Index
Freigabe
geprüft
gezeichnet 16.10.2014
PDM_Nr TD-0026642
01
24.02.2015
24.02.2015
ts
ts
ts
01 ts
24.02.2015
Protection
external switch

english
|
19
5.4 Connecting Biral Connector
17mm
961810_02
Max. 1,5mm²
Ø5,5 - 10mm
7mm
12mm
Alpha-Stecker komplett
PrimAX, ModulA BG2
Alpha-Stecker
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1.1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961810
Änd.Index
Freigabe
geprüft
gezeichnet 17.10.2014
PDM_Nr TD-0027471
02
31.08.2015
31.08.2015
ts
ts
ts
02 ts
31.08.2015
For ModulA circulation pumps with a maximum
power consumption of 200 Watts power supply
is ensured via Biral Connector.
5.5 Connection drawing Clamp description
Extern ON Power Limit ON
SSM
32
Power Limit OFF Extern OFF
11
BM
ON
2 3
Potentialfrei
AC in
~1x230V ±10%
50/60 Hz
1x230V
max. 250V AC
2A
min. 5V DC
20mA
DC out
24V
Extern
OFF/ON
SSM/BM
max.20mA
N
51 L54521011 4- +2
IL00001955_00
Anschlussschema
ModulA BG2
mit FU für BA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:2
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961808
Änd.Index
Freigabe
geprüft
gezeichnet 16.10.2014
PDM_Nr TD-0026660
00
17.10.2014
17.10.2014
ts
ts
ts
Terminals:
+24- DC out 24 V
11, 10 External OFF and external ON
52, 54, 51 Fault notification or operation notification
L, N, PE Mains connection, 1x230V +/– 10%, 50/60Hz
Switch (Bold lettering = as delivered
1fault notification (SSM) or operation notification (BM)
2External OFF or external ON
3Power limit ON or Power Limit OFF

20 | english
5.6 Switch settings
5.6.1 Switch 1, Fault or operating signal (switchable)
The pump has a signal relay with potential-free changeover contact for external fault notification.
The signal relay can be switched over to operation notification via switch 1.
Connection
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
max. 250V AC
2A
min. 5V DC
20mA
961827_00
DC out
24V
max. 20mA
515452
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
961827_00
DC out
24V
max. 20mA
515452
515452
515452
515452
515452
Relaisaugänge
ModulA
51,52,54
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961827
Änd.Index
Freigabe
geprüft
gezeichnet 13.11.2014
PDM_Nr TD-0028419
00
ts
Status
Connection
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
max. 250V AC
2A
min. 5V DC
20mA
961827_00
DC out
24V
max. 20mA
515452
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
961827_00
DC out
24V
max. 20mA
515452
515452
515452
515452
515452
Relaisaugänge
ModulA
51,52,54
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961827
Änd.Index
Freigabe
geprüft
gezeichnet 13.11.2014
PDM_Nr TD-0028419
00
ts
Status
fault notification (SSM)
Switch
1
OFF
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
max. 250V AC
2A
min. 5V DC
20mA
961827_00
DC out
24V
max. 20mA
515452
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
961827_00
DC out
24V
max. 20mA
515452
515452
515452
515452515452
Relaisaugänge
ModulA
51,52,54
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961827
Änd.Index
Freigabe
geprüft
gezeichnet 13.11.2014
PDM_Nr TD-0028419
00
ts
Impeller green
fault signal
inactive
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
max. 250V AC
2A
min. 5V DC
20mA
961827_00
DC out
24V
max. 20mA
515452
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
961827_00
DC out
24V
max. 20mA
515452
515452
515452
515452515452
Relaisaugänge
ModulA
51,52,54
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961827
Änd.Index
Freigabe
geprüft
gezeichnet 13.11.2014
PDM_Nr TD-0028419
00
ts
Impeller green
fault signal
inactive
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
max. 250V AC
2A
min. 5V DC
20mA
961827_00
DC out
24V
max. 20mA
515452
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
961827_00
DC out
24V
max. 20mA
515452
515452
515452
515452515452
Relaisaugänge
ModulA
51,52,54
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961827
Änd.Index
Freigabe
geprüft
gezeichnet 13.11.2014
PDM_Nr TD-0028419
00
ts
Impeller red
fault signal
active
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
max. 250V AC
2A
min. 5V DC
20mA
961827_00
DC out
24V
max. 20mA
515452
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
961827_00
DC out
24V
max. 20mA
515452
515452
515452
515452515452
Relaisaugänge
ModulA
51,52,54
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961827
Änd.Index
Freigabe
geprüft
gezeichnet 13.11.2014
PDM_Nr TD-0028419
00
ts
Impeller red
fault signal
active
operating notification (BM)
Switch
1
ON
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
max. 250V AC
2A
min. 5V DC
20mA
961827_00
DC out
24V
max. 20mA
515452
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
961827_00
DC out
24V
max. 20mA
515452
515452
515452
515452515452
Relaisaugänge
ModulA
51,52,54
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961827
Änd.Index
Freigabe
geprüft
gezeichnet 13.11.2014
PDM_Nr TD-0028419
00
ts
turning impeller
operating signal
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
max. 250V AC
2A
min. 5V DC
20mA
961827_00
DC out
24V
max. 20mA
515452
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
961827_00
DC out
24V
max. 20mA
515452
515452
515452
515452515452
Relaisaugänge
ModulA
51,52,54
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961827
Änd.Index
Freigabe
geprüft
gezeichnet 13.11.2014
PDM_Nr TD-0028419
00
ts
turning impeller
operating signal
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
max. 250V AC
2A
min. 5V DC
20mA
961827_00
DC out
24V
max. 20mA
515452
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
961827_00
DC out
24V
max. 20mA
515452
515452
515452
515452515452
Relaisaugänge
ModulA
51,52,54
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961827
Änd.Index
Freigabe
geprüft
gezeichnet 13.11.2014
PDM_Nr TD-0028419
00
ts
stationary impeller
operating signal
inactive
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
max. 250V AC
2A
min. 5V DC
20mA
961827_00
DC out
24V
max. 20mA
515452
10
5
8
6
6
5 5
8
6
6
3.3
[phone] L51 N
AC in
~1x230V
±
10%
50/60 Hz
961827_00
DC out
24V
max. 20mA
515452
515452
515452
515452515452
Relaisaugänge
ModulA
51,52,54
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
1:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961827
Änd.Index
Freigabe
geprüft
gezeichnet 13.11.2014
PDM_Nr TD-0028419
00
ts
stationary impeller
operating signal
inactive
961827_00
ON
1 2 3
961865_01
ON
1
ON
1
2
ON
2
ON
ON
3
ON
3
Switch 3
ModulA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
3:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961865
Änd.Index
Freigabe
geprüft
gezeichnet 10.12.2014
PDM_Nr TD-0028816
01
nma
01 ts
16.01.2015
ON
1 2 3
961865_01
ON
1
ON
12
ON
2
ON
ON
3
ON
3
Switch 3
ModulA
CH-3110 Münsingen
Biral AG
Massstab
Zeichnungsnummer
3:1
III
Datum Änd.Index Visum
Ersetzt durch: Ersatz für:
961865
Änd.Index
Freigabe
geprüft
gezeichnet 10.12.2014
PDM_Nr TD-0028816
01
nma
01 ts
16.01.2015