Black & Decker BXFP51006GB User manual

BXFP51006GBwww.blackanddecker.co.uk

ENGLISH (Original instructions)
2
What’s in the box
Instruction Manual
Digital Pedestal Fan
Remote Control
Screw
Features
1. Guard and Blades
2. LCD Display
3. Control Panel
4. Height Adjustment Key
5. Base
LCD & Control Panel
6. Speed/ Timer Display
7. Oscillation Display
8. Time/ Pre-set Display
9. Oscillation Display
10.Natural Wind Mode Display
11. Normal Wind Mode Display
12.Sleep Wind Mode Display
13.ON/OFF Button
14.Oscillation Button
15.Wind Mode Button
16.Program Timer Button
17.Speed Button
2
1
6
8
10
13
7
12
15
17
9
11
14
16
3
4
5

ENGLISH
(Original instructions)
3
Intended Use
Your BLACK+DECKER BXFP51006GB 16” Digital
Pedestal Fan with 12 Hour Timer has been designed
for cooling small and medium spaces.
This appliance is intended for indoor household use
only.
Thank you for choosing BLACK+DECKER. We hope
that you will enjoy using this product for many years.
Safety Instructions
WARNING: Read all safety
warnings and all instructions. Failure
to follow the warnings and
instructions listed below may result in
electric shock, re and/or serious
injury.
♦ Read this manual carefully before
using the appliance.
♦ The intended use is described in
this manual.
♦ The use of any accessory or
attachment or the performance of
any operation with this appliance
other than those recommended in
this instruction manual may present
a risk of personal injury.
♦ Retain this manual for future
reference.
WARNING: When using mains-
powered appliances, basic safety
precautions, including the following,
should always be followed to reduce
the risk of re, electric shock,
personal injury and material damage.
Using Your Appliance
Please read the operating
instructions carefully before using
your fan for the rst time.
♦ Check that the voltage of the main
circuit corresponds with the rating
of the appliance before operating.
♦ Children shall not play with the
appliance.
♦ Do not let the cable hang over the
edge of a table or counter or let
it come into contact with any hot
surfaces.
♦ The use of accessory attachments
is not recommended by the
appliance manufacturer, apart from
those supplied with this product.
♦ Do not pull the plug out by the
cable as this may damage the plug
and/or the cable.
♦ Do not use this product for anything
other than its intended use.
♦ This appliance is for household use
only.
♦ Do not carry the appliance by the
power cable.
♦ Do not use the appliance outdoors.
♦ Do not operate with wet hands.
♦ Use of an extension cable with this
appliance is not recommended.
However, if it is necessary to use
an extension lead, ensure that
the lead is suited to the power
consumption of the appliance to
avoid overheating of extension
cable, appliance or plug point. Do
not place the extension cable in a

ENGLISH (Original instructions)
4
position where it can be pulled on
by children or animals or tripped
over.
♦ Always unplug the unit when not in
use or before cleaning.
♦ The manufacturer does not accept
responsibility for any damage
or injury caused by improper or
incorrect use, or for repairs carried
out by unauthorised personnel.
Safety Of Others
♦ Close supervision is necessary
when any appliance is used by or
near children.
♦ Children should not play with the
appliance.
♦ This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance
in a safe way and understand the
hazards involved.
♦ Cleaning and user maintenance
should not be undertaken by
children without supervision.
♦ Take care when any appliance is
used near pets.
♦ Do not allow the cord to become
twisted.
After Use
♦ While cleaning, DO NOT use a wet
cloth or use water on any part of
the unit, as this may cause a short
circuit or electrical shock.
♦ Keep this unit clean. Do not allow
objects to enter the ventilation
opening as this may cause electric
shock, or damage to the unit.
Switch off the unit and then remove
the plug from the socket when not
in use or before cleaning.
♦ Check all inlets and outlets
regularly for accumulated dust.
♦ Disconnect the unit from mains
outlet when it is not in use, or
before relocating or cleaning it.
♦ Switch off and remove the plug
from the socket before leaving the
appliance unattended and before
changing, cleaning or inspecting
any parts of the appliance.
♦ When not in use, the appliance
should be stored in a dry place.
Children should not have access to
stored appliances.
Inspections And Repairs
♦ Do not attempt to dismantle, repair
or remould any part of the unit. This
should only be done by a qualied
service agent. Even the change of
power cable should be done by a
qualied person.

ENGLISH
(Original instructions)
5
♦ In the unlikely event the appliance
develops a fault, stop using it
immediately and seek advice from
the manufacturer.
♦ In case of technical problems,
switch off the product and do not
attempt to repair it yourself. Return
the appliance to an authorised
service facility for examination,
adjustment or repair. Always
insist on the use of original spare
parts. Failure to comply with the
above mentioned precautions and
instructions, could affect the safe
operation of this product.
Additional safety instructions for
Air Coolers and Fans
♦ Install the unit on at and hard oor
to diminish vibration or noise.
♦ Always operate the appliance on a
smooth, even, stable surface. Do
not place the unit on a hot surface.
♦ Ensure that the unit is switched off
after use.
♦ Do not immerse cables, plugs or
any part of the appliance in water
or any other liquid.
♦ Operate the unit only at the voltage
specied.
♦ Do not use the unit near open
windows, as contact with rain and
other natural elements could cause
an electrical hazard
♦ Do not put heavy objects on the
appliance.
♦ Do not tip the unit on its side.
♦ Never insert any other object into
the unit body to avoid any hazard
or unit failure.
♦ Do not put the unit close to
heat-generating devices or
near ammable and dangerous
materials.
♦ If the supply cable is damaged,
it must be replaced by the
manufacturer or its service agent or
a similarly qualied person in order
to avoid a hazard
♦ The appliance must be positioned
so that the plug is accessible.
♦ For optimal airow circulation,
leave a distance of at least 1 metre
around the appliance on every side.
Always direct the airow in order
to optimise cooling. Avoid corners,
small objects and other surfaces
or objects which may impede the
airow.
WARNING: Do not place the unit
on or near a hot gas electric burner.

ENGLISH (Original instructions)
6
Electrical safety
Before use, check that the mains voltage
corresponds to the voltage on the rating plate.
Always check that the mains voltage
corresponds to the voltage on the rating
plate.
♦ Appliance plugs must match the outlet. Never
modify the plug in any way.
♦ Do not use any adapter plugs with this appliance.
Unmodied plugs and matching outlets will reduce
the risk of electric shock.
♦ To avoid the risk of electric shock, do not immerse
the cord, plug or appliance in water or other liquid.
Extension cables & class 2 product
♦ A 2 core cable must be used as your tool is not
earthed.
♦ Up to 30m (100 ft) can be used without loss of
power.
♦ If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised
BLACK+DECKER Service Centre in order to avoid
a hazard.
WARNING: Before assembling, switch the
appliance off and remove the plug from the socket.
Features (Refer to diagram on page 2)
1. Guard and Blades
2. LCD Display
3. Control Panel
4. Height Adjustment Key
5. Base
Use
About the Controls
♦ Push button controls with LCD display
♦ 6 Speed settings
♦ 3 Fan modes
♦ 12hr Timer with 30 minute increments
♦ 3 Oscillation functions
Remote Control
ON/OFF button
Speed buttons
Timer button
Oscillation button
Wind mode button

ENGLISH
(Original instructions)
7
Installing the Battery
WARNING: Battery acid leakage can cause
personal injury and cause damage to the product
and surrounding property. If battery leakage occurs,
thoroughly wash any affected skin, making sure to
keep battery acid away from eyes, ears, nose and
mouth. Immediately wash any clothing or other
surface that comes in contact with leaked battery
acid. If a chemical burn occurs or if irritation persists,
seek medical attention. Dispose according to Local,
State or Federal regulations.
WARNING: NEVER mix old and new batteries or
different brands of batteries. Replace all batteries at
the same time.
WARNING: NEVER mix alkaline, standard
(carbon-zinc), rechargeable (nickel-cadmium)
batteries with this product.
WARNING: NEVER dispose of batteries in re, as
they may leak and explode.
WARNING: ALWAYS remove exhausted batteries
from product.
♦ Batteries are to be inserted following the polarity
markings on the product.
♦ Remove batteries before extended storage.
To Begin Using Your Fan
♦ To begin using this unit, start by installing the
batteries in the remote control. DO NOT use
rechargeable batteries.
♦ To install the batteries, rst detach the battery
cover from the remote. To do this, place your
nger on the grooved area at the centre of the
battery cover and push down and away from the
body of the remote.
♦ Insert 2 x AAA batteries into the battery
compartment, taking care to ensure the polarities
are correct.
♦ Once the batteries have been correctly inserted,
replace the battery cover by aligning each of the
locking tabs with the corresponding notch on the
remote control body and pushing it upwards until it
clicks into place.
♦ The remote control is now ready for normal use.
Assembling Your Fan
WARNING: Before performing any assembly or
maintenance, switch the unit off and remove it from
the power supply.
♦ Carefully remove the fan from the carton and
place it at on the oor.
♦ Align the column with the groove on the base and
x them together using the lock nut.
♦ Tighten the locknut to secure the column and
base unit together.
♦ Once the column is secured to the fan base,
align the installation groove on the column and
the motor column and turn clockwise to x the
connection. Use the screw provided to secure
further.
♦ Align the rear grille with the motor shaft.
♦ Align the grille locknut with the motor shaft and
turn clockwise to x the rear grille.
♦ Align and attach the blade, to the motor shaft
checking that it can rotate normally.
♦ Align the blade locknut and turn anti-clockwise to
hold the blades in place.
♦ Attach the front grille and secure to the rear grille:
Align the Front Grille catch with the illustrated
position of the Rear Grille. (See diagram on
page 2). With both hands, press the grilles
together sequentially.
Press the catch over the grilles to x in place.
Note! Do not remove the grilles once tted.
♦ Adjust the height of the unit by turning the
height adjustment key and then raising/ lowering
the column as required. Re-tighten the height
adjustment key to lock in place.
(See diagram on page 8)

ENGLISH (Original instructions)
8
Turning the Unit On or Off
♦ To turn the unit on, begin by plugging it into the
mains. There will be a sound prompt to indicate
the fan is in stand-by mode.
♦ Press the On/Off key to turn the unit on. There will
be a sound prompt to indicate the unit has been
turned on, and the fan will automatically begin to
operate at the last speed setting used.
♦ Press the On/Off button again while the unit is
in operation to turn it off. There will be a sound
prompt to indicate the unit has been turned off.
Note! When the unit is turned off, the blades will
continue to turn for a few seconds before stopping
completely.
Speed Selection
♦ This unit is equipped with a choice of 6 speed
settings.
♦ Repeatedly press the Speed button to cycle
through the settings.
Timer
♦ This unit is equipped with a built-in timer, which
allows for pre-set cooling cycles of up to 12 hours.
♦ Repeatedly press the Timer button to until the
required time is displayed. Note! The timer will
change in increments of 30 minutes from 0.0 to
10 hours, and in increments of 1 hour from 10 to
12 hours.
♦ Once a time has been set, the fan will operate on
the selected settings for the set amount of time,
then shut itself off automatically once it expires.
The corresponding icon will illuminate to show that
a Timer has been set.

ENGLISH
(Original instructions)
9
Oscillation
♦ This fan is equipped with an oscillation function.
♦ Press the oscillation button to turn the oscillation
function on. The fan will automatically begin to
swing from side to side. The corresponding icon
will illuminate.
♦ Press this button again while the unit is oscillating
and the fan will move up and down. The
corresponding icon will illuminate.
♦ Press this key again and the fan will oscillate in
a gure of 8 up and down and side to side. Both
Corresponding icons will illuminate.
♦ Press this button again to turn the oscillation
function off. Both corresponding icons will go off.
Wind Mode
♦ This unit allows for the control of the air ow;
Normal, Natural or Sleep.
♦ Press the Wind Mode button to cycle through
the available modes. The corresponding icon will
illuminate to conrm the mode selected.
Cleaning and maintenance
WARNING: Before cleaning and maintenance,
switch the appliance off and remove the plug from
the socket, to prevent electric shock.
♦ Do not immerse any part of the appliance, power
cord or plug in liquids..
♦ Use a soft damp cloth to wipe the surface. Avoid
using detergent, spray or chemicals as these may
cause damage to the appliance.
WARNING: DO NOT allow water or steam to
enter any part of the appliance, as this could cause it
to malfunction.
♦ Store the appliance in a cool, dry place, ideally in
its original packaging.
Mains plug replacement
WARNING: The following section on mains plug
replacement is for authorised service centre persons
only.
If a new mains plug needs to be tted:
♦ Safely dispose of the old plug.
♦ Connect the brown lead to the live terminal in the
new plug.
♦ Connect the blue lead to the neutral terminal.
♦ If the product is class I (earthed), connect the
green/yellow lead to the earth terminal.
Note! If your product is class II double insulated
(only 2 wires in the cord set), no connection is to be
made to the earth terminal.
Follow the tting instructions supplied with good
quality plugs. Any replacement fuse must be of the
same rating as the original fuse supplied with the
product.
Protecting the environment
Separate collection. Products and
batteries marked with this symbol must
not be disposed of with normal household
waste.
Products and batteries contain materials that can
be recovered or recycled, reducing demand for
raw materials. Please recycle electrical products
and batteries according to local provisions. Further
information is available at www.2helpU.com.
Technical data
BXFP51006GB
Input voltage V AC 220-240V
Frequency Hz 50
Power input W55
Weight KG 7.8

ENGLISH (Original instructions)
10
Product Guarantee
This product comes with a 2 Year guarantee from
the original date of purchase. If any defect arises
due to faulty materials or workmanship, the faulty
products must be returned to the place of purchase.
Refund or replacement is at the discretion of the
retailer. This guarantee is in addition to and in no
way prejudices your statutory rights.
The Following Conditions Apply:
♦ The product must be returned to the retailer
with proof of purchase or a receipt within the
1st year of purchase. For any product related
issues after 12 months please contact our
customer services team.
♦ The product must be installed and used in
accordance with the instructions contained in
this instruction guide.
♦ It must be used only for domestic purposes.
♦ It does not cover wear and tear, damage,
misuse or consumable parts.
♦ This guarantee is valid in the UK and Republic
of Ireland.
For all customer service enquires please
contact us below;
RKW,
Sutton House,
Berry Hill Road,
Stoke-on-Trent,
ST4 2NL
Email [e-mail]
Tel [phone]
Black & Decker® and BLACK+DECKER™ and the
Black & Decker® and BLACK+DECKER™ logos
are registered trademarks of The Black & Decker®
Corporation and are used under licence. All rights
reserved. Imported and Distributed by RKW LTD,
Sutton House, Berry Hill Industrial Estate, Berry Hill
Road, Stoke-on-Trent, ST4 2NL