Blaupunkt IRP-S1L User manual

Wireless Pet-Immune PIR Motion Sensor (IRP-S1L)
P
Pa ar rt ts s D De es sc cr ri ip pt ti io on n
1. Learn/Test Button & LED indicator
Press the button to transmit a learn/test code and enter Test
mode for 3 minutes. The LED will light up whenever a movement
is detected under Test mode.
2. Battery Insulator
3. Supervision Enable/Disable Jumper Switch
(JP2)
4. High/Low Sensitivity Jumper Switch (JP3)
5. Tamper Switch
The Tamper switch protects the PIR from unauthorized cover
opening.
P
Pa ac ck ka ag ge e C Co on nt te en nt t
1 x PIR Sensor
4 x wall plugs and screws
1 x 3V lithium battery(pre-installed)
Supervision Enable/Disable Jumper Switch (JP2)
If enabled, the PIR sensor will transmit supervision signal to
Control Panel periodically for the sensor to monitor PIR sensor
condition.
Jumper set to ON = supervision function is Disabled
Jumper set to OFF = supervision function is Enabled (Default)
High/Low Sensitivity Jumper Switch (JP3)
Jumper set to ON = PIR sensitivity is set to High (Default)
Jumper set to OFF= PIR sensitivity is set to Low
Put the Control Panel into learning mode, then press the learn
button to transmit learn code. Please refer to Control Panel
manual for to complete the learning process.
The PIR Sensor has knockouts on the back where plastic is
thinner. The 2 center knockouts are for flat wall mounting, and the
4 side knockouts are for corner mounting. Mount the PIR Sensor
at 1.9m to 2m height for optimal performance.
1. Break through the knockouts; use the knockouts to mark
position on the wall or corner.
2. Drill holes into the wall or corner using the knockouts as
template.
3. Fix the PIR Sensor base onto the wall with the screws and
plugs provided.
4. Replace the PIR Sensor cover onto the base.
S
Sl le ee ep p T Ti im me er r
The PIR features a “sleep time” of approximately 1 minute for
power conservation. After transmitting a detected movement, the
PIR will not retransmit for 1 minute. Any further movement
detected during this sleep period will extend the sleep time by
another minute. In this way continuous movement in front of a
PIR will not unduly exhaust the battery.
T
Te es st t M Mo od de e
Press the Test Button to enter Test mode for 3 minutes. Sleep
timer will be disabled under Test mode, and the LED indicator will
flash every time a movement is detected. Use the Test mode to
determine PIR detection coverage and plan the installation
location accordingly.
L
LE ED D I In nd di ic ca at to or r
Off
Normal Operation
On (2 seconds)
- When Tamper Switch is triggered
- Movement detection under low battery,
tamper triggered, or Test mode.
Jumper On
The jumper link is inserted
connecting the two pins
Jumper Off
if the jumper link is removed
or parked on one pin.
Jumper On
The jumper link is inserted
connecting the two pins
Jumper Off
if the jumper link is removed
or parked on one pin.
L
Le ea ar rn ni in ng g
O
Op pe er ra at ti io on n
I
In ns st ta al ll la at ti io on n
Surface Fixing
Knockouts x 2
(Inside)
Corner Fixing
Knockouts x 4

P
Pe et t I Im mm mu un ni it ty y
The PIR has pet-immune function and will not trigger false alarm
from household pet under approximately 27 kg within 7 meters.
Please note this is a rough estimate number and the actual pet
immune performance may vary according to your home
environment and pet size. For example, a dog standing on its
hind legs or a cat climbing on furniture may trigger alarm more
easily than when they are standing on floor. Please test the pet
immune function with your pets to find out the ideal installation
location before mounting the PIR.
B
Ba at tt te er ry y
The PIR uses one 3V lithium battery as its power source.
Remove the battery insulator to activate battery. It also features
low battery detection function to notify the Control Panel when
battery voltage is low.
When PIR is on low battery, follow the procedure below to
change the batteries.
1. Open the PIR back cover.
2. Remove the old batteries.
3. Press the tamper switch several times to fully discharge.
4. Insert the new batteries observing correct polarity. The PIR
LED will light up for 30 seconds to indicate it is warming up.
5. Replace the PIR back cover.
E
En nv vi ir ro on nm me en nt ta al l C Co on nd di it ti io on n
-10°C to 40°C, relative humidity 85% non-condensing.
R
Ra ad di io o
868 MHz
S
Sp pe ec ci if fi ic ca at ti io on n