BLOTZ B28-OW-108 User manual

28mm Old West Store #1
B28-OW-108
Assembly Instructions
Designed and made in the UK.
This is a model kit and is not intended for persons
under 14 years old.
Requires assembly. Supplied unpainted.

28mm Old West High Front #1
B28-OW-420
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember
to cut away from yourself at all times.
During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while
you allow glue to dry.
Remove the two base pieces and the frame from the
sprue.
Glue the frame to the plank section, then glue the
other base section under it using the lugs to align
them.
Glue the rear plate into place.
While the assembly dries, place it against a rear
section to ensure it doesn’t tilt forwards.
Take the insert pieces from the sprue.
Glue these into the gaps in the framework.

Take the door and supports from the sprue.
Glue the lower support into place. Allow to dry.
Place the lower lug of the door into the lower support,
then sit the upper support onto the top lug before
gently easing it into place (see example pic).
Apply some glue to the upper support and then slide
it completely into position.
The windows and sills.
Glue the sills into place at the bottom of the window
gaps.
then glue the windows into place.
Glue the top bar into place.
The completed front.

28mm Old West Rear #4
B28-OW-503
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember
to cut away from yourself at all times.
During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while
you allow glue to dry.
Remove the base piece and the two long inner walls
from the sprue.
Glue the walls to the planked base so that all etched
detail Is facing inwards (see pic).
Note: Two lugs will extend through the floor.
Glue the base plate into position, using the lugs to
align it.
Add the back wall.
Take the pieces for the side extension from the
sprue.
Glue one wall to the frame piece (see pic)
Then attach this to the model.

Add the small side and front walls to the extension.
Take the frame pieces from the sprue.
Glue the frames into position (see pic).
The thinner part of the frame (with the sprue points on
it) should be at the bottom.
The main insert pieces.
Pop these into position.
The extension insert pieces.
Glue these into place.
The window sills.
Glue a sill below each window.
The pieces of the extension roof.

Glue the stripts into place.
Place (do not glue) the roof onto the extension.
The completed rear.

28mm Old West Upper #1
B28-OW-520
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember
to cut away from yourself at all times.
During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while
you allow glue to dry.
Remove the base piece and the inner walls from the
sprue.
Glue the walls to the planked base so that all etched
detail Is facing inwards (see pic).
Note: Four lugs will extend through the floor.
Take the frame pieces from the sprue.
Then add them as shown above.
The thinner part of the frame (with the sprue points on
it) should be at the bottom.
The insert panels for the sides.
Glue these into place.
Add the inserts for the back wall.

The window sills.
Glue a sill below each window.
The completed upper section.

28mm Old West Roof #5
B28-OW-604
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember
to cut away from yourself at all times.
During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while
you allow glue to dry.
Remove the pieces shown above from the sprue.
Glue the support bars through the holes in the roof
plate.
Glue the end pieces and ridge bar into place.
The end “frames”
The blank “frame” goes at the end nearest the support
bars. The open frame goes in the other end (see pic)
Add the insert pieces into the frame.
Glue the roof pieces into place.
The roof strips.

Glue the strips into place.
The completed roof.

28mm Old West Porch #3
B28-OW-652
Please read these instructions fully before starting construction.
PVA or equivalent glue will be required to stick sections together.
Sand paper can be used to gently clean any joints.
A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember
to cut away from yourself at all times.
During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while
you allow glue to dry.
Remove the pieces of the porch from the sprue.
Glue the floor to the back of the main piece as
shown above.
Glue the sides into position.
Attach the porch to a building of your choice such as
the one shown above.