BMW 84 63 0 144 415 User manual

Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
2
ABC
3
DEF
4
GHI
5
JKL
6
MNO
7
PQRS
8
TUV
0
9
WXYZ
1
F 53 0443 2W
aA
ÄÖÜ
BMW Siemens Cordless car phone upgrade kit
BMW X5 (E 53) from 09/01
These installation instructions are only valid for cars with SA 640
The installation time is approx. 2.5 hours, but this may vary depending on the condition of the
car and the equipment in it.
Retrofit kit No. 84 63 0 144 415
Parts and Accessories
Installation Instructions

EN/2
Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
Contents
Section Page
Important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1. Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Installation and cabling diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4. To install and connect the transceiver module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. To install and connect the eject box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6. To install the hands-free microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
7. To register a cordless receiver on the transceiver . . . . . . . . . . . . . . . . . . . . . . . . . 12
8. Concluding work and coding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

EN/3
Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
Important information
This upgrade kit is for use within the BMW dealership organisation only.
Target group
The target group for these installation instructions is specialist personnel trained on BMW cars
with specialist knowledge of vehicle electrical systems.
Work:
All servicing, repair and installation work on BMW cars is completed at your own risk.
All work is to be carried out using current BMW
- Repair manuals
- Circuit diagrams
in a rational order using the prescribed tools (special tools) and observing current health and
safety regulations.
Ordering instructions
Centre console insert
A black insert for the centre console is supplied in the upgrade kit.
An insert for the centre console in other colours for cars with different interior colours can be
ordered if required. See the EPC for all further ordering information.
Safety instructions
The current accident prevention regulations must be followed.
Refer to the safety instructions for handling components of the airbag system. Further
information is available in the TIS in RA No. 32 34 ... If you fail to follow the safety instructions
the airbag system may deploy incorrectly and cause injuries.

EN/4
Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
1. Preparations
0
TIS instruction No.
Conduct a brief test
Disconnect the negative pole of the battery 12 00 ...
The following components must be removed first of all:
Left boot – wheel arch trim 51 47 151
Oddments box 51 16 200
Ceiling light 63 31 000

EN/5
Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
2. Installation and cabling diagram
0
Legend
0
1 Hands-free microphone
2 Eject box and interface
3 Transceiver module
4 WDCT aerial
21
3
053 0067 Z
4

EN/6
Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
3. Connection overview
0
0
Item Description Signal
Cable colour
/ Cross-
section
Connection location in the car Abbreviation /
Slot
A Aerial adapter --- --- Between the standard wiring
harness and transceiver module ---
A1 FAKRA plug contact --- --- To standard aerial cable ---
A2 Mini UHF plug contact --- --- To transceiver module ---
--- --- ---
--- --- ---
B Adapter eject box --- --- Between the standard wiring
harness and eject box ---
B1 Black 18-pin plug --- --- To eject box X4545
B2 Black 18-pin plug --- --- To standard wiring harness X4545
C Hands-free control module
adapter --- --- Between the standard wiring harness and transceiver module ---
C1 White 18-pin plug --- --- To standard wiring harness X18618
C2 Blue 26-pin plug --- --- To standard wiring harness X18626
C3 Black 25-pin plug --- --- To transceiver module X4038
B2
B
B1
C2
C1
C3
C
A1 A2
A
039 0135 Z

EN/7
Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
4. To install and connect the transceiver module
0
0
0
0
0
Bolt the bottom module holder (1) the boot on
the left (4) using hexagonal nuts M6 (2) and a
hexagonal screw M6 (3).
Place speed nuts (4) on the bottom module
holder (1).
0
Insert speed nuts (1) as shown on to the top
module holder (2 and 3) and secure them with
hexagonal screws (4).
Bolt the module holders (2 and 3) to the boot on
the left using hexagonal screws (5) and hexagonal
nuts (6).
0
Connect branch C3 to the transceiver module (1).
0
Place the transceiver module (1) and retaining
bar (2) on the bottom module holder (3) and
secure them with plastic nuts (4).
2
4
3
1
053 0055 Z
4
5
1
6
3
2
5
053 0056 Z
1
C3
053 0105 Z
1
32
4
053 0058 Z

EN/8
Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
4. To install and connect the transceiver module
0
0
0
0
Connect the cable for the WDCT aerial (1) to the
transceiver module (2).
Connect the aerial adapter A between the
transceiver module (2) and the cars aerial
cable (3).
0
Secure the WDCT aerial (1) to the top module
holder (3) using plastic nuts (2).
0
Connect the aerial cable (1) to the WDCT aerial (2).
A3
1
2
053 0059 Z
3
1
2
053 0060 Z
053 0061 Z
1
2

EN/9
Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
5. To install and connect the eject box
0
0
0
0
0
Undo the Allen bolts (1) from the armrest (2) and
remove the cover (3).
0
Take the springs (1) out of the armrest (2).
Remove both bolts (3) with a punch and pull the
guide arm (4) upwards.
0
Unclip the cover (1) from the guide arm (2).
0
Pull the slide plate (1) on the armrest (2) backwards
as far as it will go.
Release the retaining pins on the oddments
box (3) with screwdrivers (4) and unclip the
oddments box (3).
32
1
053 0035 Z
2
13
4
053 0062 Z
1
2
053 0063 Z
1
2
3
4
053 0048 Z

EN/10
Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
5. To install and connect the eject box
0
0
0
0
Clip the eject box (1) into the armrest (2).
0
Connect the black 18-pin plug (1) on the eject box
to branch B1 .
Insert the extension cable B as shown in the guide
arm (2) and fit the cover (3) again.
Assemble the armrest again following the
instructions to dismantle it in reverse order.
0
Install the armrest back on to the centre console.
Connect branch B2 to plug X4545 on the standard
wiring harness.
1
2
053 0064 Z
1
B1
2
B3
053 0065 Z
B
B2
X4545
053 0066 Z

EN/11
Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
6. To install the hands-free microphone
0
0
0
0
Thread the tied back plug X4221 through the
microphone opening (1) in the headlining
console (2).
0
Clip the hands-free microphone (1) into the
microphone trim (2) you removed earlier.
Connect plug X4221 to the hands-free
microphone (1).
0
The arrow on the hands-free microphone (1)
must point to the front of the car.

Clip the microphone trim (1) into the headlining
console (2).
X4221
1
2
053 0044 Z
2
1
X4221
053 0045 Z
1
2
053 0046 Z

EN/12
Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
7. To register a cordless receiver on the transceiver
To ensure the correct registration of the receiver on the hands-free module the times listed
below must be observed precisely.
If your times are too long or too short, the receiver will not be registered. In this case the
registration process must be repeated.

0
0
0
0
- Position the slide switch in the eject box in
position “1”
- Turn the ignition key into position “1”
(terminal R)
- Wait for 15 seconds and then turn the ignition
key to position “0”
0
- Wait for approx. 2 seconds and then move the
slide switch in the eject box in position “0”
0
- Wait for a further approx. 2 seconds and
then move the slide switch in the eject box
in position “1”
F 38 0256 2W
I
F 38 0252 2W
I
F 38 0256 2W
I

EN/13
Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
7. To register a cordless receiver on the transceiver
0
0
0
0
- Switch on the receiver
0
- Confirm the registration request with “OK”
0
- Enter code “0000”and confirm with “OK”
- After completing the registration the normal
operator menu will appear in the display
F 39 0467 2W
F 39 0469 2W
Bitte
anmelden
F 39 0468 2W
Gerätecode:

EN/14
Retrofit kit No. 84 63 0 144 415
Installation Instructions No. 01 29 0 144 355 Issue date: 12.2001
8. Concluding work and coding
This upgrade system requires coding and must be coded using the “Retrofit”path. 
- Complete the coding procedure
- Conduct a brief test with DIS/MoDiC.
- Conduct a function test
- Assemble the car again following the instructions to dismantle it in reverse order.
If necessary, the circuit diagram for the telephone preparation (SA 640) can be taken
from the installation instructions entitled “Telephone upgrade circuit diagrams,
part No. 01 29 0 140 378”on the installation instructions CD.
