BMW X5 Wide screen monitor 16:9 retrofit kit User manual

Retrofit kit 65 90 0 136 732
Installation Instructions No. 01 29 0 141 872 Issue date: 08.2001
Wide screen monitor 16:9 retrofit kit
BMW X5 (E 53)
These installation instructions are only valid for vehicles with board monitor 4:3 and navigation
computer Mark III.
Technical and electrical knowledge required
The installation time is approx. 0.5 hours but this may vary depending on the condition of the
vehicle and the installed equipment in it.
Retrofit / Installation kit No. 65 90 0 136 732
053 0240 B
14
25
6
MODE
FM AM
3
MENU
INFO
TONE SELECT
Parts and Accessories
Installation Instructions

US/2
Retrofit kit 65 90 0 136 732
Installation Instructions No. 01 29 0 141 872 Issue date: 08.2001
Contents
Section Page
1. Important information for installing the wide screen monitor 3
2. Preparations and parts list 5
3. To install the wide screen monitor (vehicles with factory-fitted 4:3 board monitor) 6
4. To install the wide screen monitor (vehicles with retrofitted 4:3 board monitor) 7
5. Coding and concluding work 8

US/3
Retrofit kit 65 90 0 136 732
Installation Instructions No. 01 29 0 141 872 Issue date: 08.2001
1. Important information for installing the wide screen monitor
Only for use in the BMW dealer organisation.
The wide screen monitor may only be installed by a specialist workshop that has the required
special tools and manuals (servicing, repair, diagnostics, etc.).
These installation instructions are only valid for vehicle with board monitor 4:3 and
navigation computer Mark III.!
Ensure that the cables/lines are not kinked or damaged as you install them in the vehicle.
Item numbers refer only to the overview drawings and to the texts next to the appropriate figure.
All work is shown on a LHD vehicle.
Proceed in exactly the same way on RHD vehicles.
Electrical knowledge is required.
Subject to technical modifications
Required tools and equipment
MoDIC III or DIS Angle cutter Angle cutter
1/4 inch socket set Oscillating saw
Set of Philips screwdrivers Flat file
Set of flat screwdrivers Dust extractor
Cable lamp

US/4
Retrofit kit 65 90 0 136 732
Installation Instructions No. 01 29 0 141 872 Issue date: 08.2001
2. Preparations and parts list
0
0
Parts list
0
0
0
1Widescreen monitor 16:9, complete
2Widescreen monitor trim
3Widescreen monitor bracket, left
4Widescreen monitor bracket, right
5Fillister head screw M3x8 (4x)
Preparations TIS instruction No.
Print out error memory ---
Disconnect the battery 12 00 ...
Remove the décor strip next to the steering column 51 16 221
Remove the décor strip above the glove compartment 51 16 221
Remove the centre fresh air grille 64 22 161
Remove the 4:3 monitor (no longer required) 65 52 010
053 0241 B
14
25
6
MODE
FM AM
3
MENU
INFO
TONE SELECT
12
34 5

US/5
Retrofit kit 65 90 0 136 732
Installation Instructions No. 01 29 0 141 872 Issue date: 08.2001
3. To install the wide screen monitor
(vehicles with factory-fitted 4:3 board monitor)
0
0
0
0Carefully remove the reinforcements (10) shaded
grey on the board monitor module holder (11) on
the left using an oscillating saw.
0Carefully remove the reinforcements (10) shaded
grey on the board monitor module holder (11) on
the right using an oscillating saw.
After removing the reinforcements, the cuts are to
be deburred carefully with a flat file.
0Unscrew the two Philips screws (10).
Insert the left wide screen monitor bracket (3) and
the right wide screen monitor bracket (4), into the
board monitor module holder (11) as shown in the
figure.
0Secure the left wide screen monitor bracket (3) and
the right wide screen monitor bracket (4) to the
board monitor module holder (12) using the Philips
screws (10) and the securing screws (11) from the
4:3 board monitor you removed earlier.
053 0242 B
10
11
053 0243 B
10
11
053 0244 B
10
11
34
053 0245 B
12
3
11
10 10
11
4

US/6
Retrofit kit 65 90 0 136 732
Installation Instructions No. 01 29 0 141 872 Issue date: 08.2001
3. To install the wide screen monitor (vehicles with factory-fitted 4:3 board monitor)
0
0
0
0
0Connect the blue 12-pin connector (10) and the
white 12-pin connector (11) to the 16:9 wide
screen monitor (1).
Then carefully slide the 16:9 wide screen monitor
(1) into the board monitor module bracket (12).
0Secure the 16:9 wide screen monitor (1) to the left
wide screen monitor bracket (3) and the right wide
screen monitor bracket (4) with four fillister head
screws M3x8 (5).
When you fit the wide screen monitor trim
check the positions of the interlocks.!
Place the wide screen monitor trim (2) on the
16:9 wide screen monitor (1).
053 0246 B
11
10
1
12
053 0247 B
1
4
3
5
5
5
5
2

US/7
Retrofit kit 65 90 0 136 732
Installation Instructions No. 01 29 0 141 872 Issue date: 08.2001
4. To install the wide screen monitor
(vehicles with retrofitted 4:3 board monitor)
0
0
0
0
0Remove the bottom board monitor holder (10) and
spacer plate (11).
0Carefully remove the reinforcements (10) shaded
grey on the radio module holder (11) on the right
using an oscillating saw.
0Carefully remove the reinforcements (10) shaded
grey on the radio module holder (11) on the left
using an oscillating saw.
After removing the reinforcements, the cuts are to
be deburred carefully with a flat file.
0Unscrew the two Philips screws (10).
Insert the left wide screen monitor bracket (3) and
the right wide screen monitor bracket (4), into the
radio module bracket (11) as shown in the figure.
053 0248 B
11 10
053 0249 B
11
10
053 0250 B
11 10
053 0251 B
11
34
10

US/8
Retrofit kit 65 90 0 136 732
Installation Instructions No. 01 29 0 141 872 Issue date: 08.2001
4. To install the wide screen monitor (vehicles with retrofitted 4:3 board monitor)
0
0
0
0
0Secure the left wide screen monitor bracket (3) and
the right wide screen monitor bracket (4) to the
radio module holder (11) using the Philips screws
(10) and the securing screws (11) from the 4:3
board monitor you removed earlier.
0Connect the blue 12-pin connector (10) and the
white 12-pin connector (11) to the 16:9 wide
screen monitor (1).
Then carefully slide the 16:9 wide screen monitor
(1) into the radio module bracket (12).
0Secure the 16:9 wide screen monitor (1) to the left
wide screen monitor bracket (3) and the right wide
screen monitor bracket (4) with four fillister head
screws M3x8 (5).
When you fit the wide screen monitor trim
check the positions of the interlocks.!
Place the wide screen monitor trim (2) on the
16:9 wide screen monitor (1).
053 0252 B
12
3
11 10 10
11
4
053 0246 B
11
10
1
12
053 0254 B
1
4
3
5
5
5
5
2

US/9
Retrofit kit 65 90 0 136 732
Installation Instructions No. 01 29 0 141 872 Issue date: 08.2001
5. Coding and finish work
0
Coding
This wide screen monitor does not require coding.
Finish work
Connect battery
Conduct a function test
Reassemble the vehicle by following the instructions for its disassembly in reverse order
Print out error memory