BMW SA640 User manual

F 39 0060 M
Best.-Nr. 01 29 9 416 691 XI/98 Printed in Germany
Teile und Zubehör - Einbauanleitung
BMWParts and Accessories – Installation Instruction
BMWGSM network mobile phone for the BMW5 Series (E39/2) touring
(cars without SA640 telephone preparation)

Contents Page
1Important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
2Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
3Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
4Circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

1-2/EN
Specialist knowledge required.
1 Important information
(Only for use within the BMW dealer organisation).
Installation time approx. 4-6 hours.
The installation times may vary depending on the condition of the car and the equipment in it.
These installation instructions are only for cars without SA 640 (telephone preparation).
Target group
The target group for these installation instructions is staff who have been trained on BMW cars.
Work
All servicing, repair, installation and adjustment work on cars is completed at your own risk.
All work is to be completed using the latest BMW
–Repair instructions,
–Circuit diagrams,
–Service manuals,
–Work instructions,
–Diagnostics manuals
in a rational sequence using the prescribed tools (special tools) and pursuant to the relevant health and safety
regulations.
Safety notes
Please read the following before starting the installation work:
If the specified PIN slots are already in use, bridges, double crimps or parallel end stops are to be used.
All work is shown for a left-hand drive model. On right-hand drive models the work must be completed
the opposite way round.
The installation kit does not contain any colour-dependent parts.
The MID with telephone key is not required for the function of the telephone and should only be fitted with
the consent of the customer (additional cost).
All wiring harnesses are to be laid such that they cannot be kinked, chafed or crushed.

1-10/EN
1.1 Telephone/Hands-free facility installation kit
Fold out the folded page 17.
The switch with the telephone key for the multi-functional steering wheel and the MID are not supplied in the
installation kit and must be ordered separately.
The parts marked * may have to be ordered separately depending on the equipment in the car.
1) Parts are not included in the installation kit and must be ordered separately for cars without a BMW Professional
DSP hi-fi system.
Items Description
1Additional wiring harnesses
Quantity
II - Power supply wiring harness 1
III - Microphone wiring harness 1
IV - Speaker wiring harness1) 1
VI - Adapter cable for switch module (with BM radio only)1) 1
2Slot-in nut, M5 2
V- Switch module1) 1
3Base interface 1
5Hexagonal screw, size M5x14 2
4Holder (base interface) 1
I- Mobile phone connection cable 1
6Plastic nut, size 10 mm 2
8Holder for cable compensator 1
9Hexagonal nut, size 8mm 4
10 Cable compensator 1
12 Microphone 1
13 Eject box 1
11 Microphone cover (cars with sunroof only) 1
14 Philips screw St 4.2x22 4
16 Microphone cover (cars without sunroof only)* 1
15 Cover for sunroof motor (cars with sunroof only)* 1
7Cable holder 1
17 Trim (cars without sunroof only)* 1
18 Support frame (cars without sunroof only) 1
20 Cable ties 10
19 Plug connector holder 1
21 10 A fuse 1

2
8
1
13
16 1
I
III
II
IV
V
VI
VlI

1-17
3465 7
910 11 12
14 15
17 18 19 20 21
F 39 84 156 M

2 Installation
Notes
Refer to the safety instructions in section 1.
The installation work is based on the general workshop information. Any work which differs from this is described
in detail in sections 2 and 3.
Preparatory work................................................... See section 3.1
Fold out folded page 17.
A
1Additional wiring harnesses (I-VI).............................. Lay and connect, see section 3.5
Connection overview
- Connection cable/Power supply wiring harness,
see section 3.2
- Microphone wiring harness/Speaker wiring harness,
see section 3.3
- Switch module, see section 3.4.
B
2Slot-in nuts (2)....................................................... Place on the holder (4).
3Base interface (3) .................................................. Place the base interface (3) on the holder (4) and
secure it with two hexagonal screws (5), M5x14.
Tightening torque 5 Nm.
4Holder (4)............................................................... Place the holder with the attached base interface (3)
on the left-hand wheel arch (22) and secure it with
two plastic nuts (6), size 10 mm.Tightening torque
3 Nm. Connect branch I/2, 54-pin socket casing,
to the base interface.
5Hexagonal screw (5), size M5x14
6Plastic nuts (6), size 10 mm
C
7Cable holder (7)..................................................... Place the cable holder (7) on the holder (8) for the
cable compensator.
8Holder (8) for cable compensator
9Hexagonal nut (9), size 8 mm
10 Cable compensator (10) ............................................ Place the cable compensator (10) on the holder (8) for
the cable compensator and secure it with two hexagonal
nuts (9), size 8 mm. Connect branches I/4 and I/5.
Connect the aerial cable (23). Secure the cable
compensator (10) to the reinforced brace (24) from the
rear using two hexagonal nuts (9), size 8 mm.Tightening
torque 3 Nm. Attach the cable from branch I/5 to the
cable holder (7).
D
11 Microphone cover (11) ........................................... Install the microphone cover, see section 3.6
12 Microphone (12) .................................................... Install and connect the microphone, see section 3.6.
E
13 Eject box (13) ........................................................ Insert the eject box (13) into the telephone centre
armrest and press it downwards until the engagement
pins click into position.
Installation/Connection, see section 3.7.
The telephone centre armrest must be ordered
separately to match the trim colour (see ETK / MF
for part number).
F
14 Control switch (25) ................................................ Replace the control switch with the telephone key.
Cars with multi-functional steering wheel only.
EN/2-3

G
15 MID (26) ................................................................ Replace the MID or IRIS with an MID with a telephone
key.
On cars without an on-board monitor radio and
with a "C32 Reverse RDS" radio, the radio must be
replaced and the additional wiring harness for the
MID retrofit installed.The corresponding MID with
a telephone key must be ordered separately.
2-4/EN

II
I
IV
III
25
26
13
A
EF
G
F 39 84 157 M
F 39 84 164 MF 39 84 165 M
F 39 84 166 M
F 39 0114 M

VI
V
8
9
7
10
10
23
I/5
7
24
I/4
9
4
5
2
11 12
3
3
6
I/2
4
622
F 39 0118 M
B
C
D
F 39 84 159 M
F 39 84 161 M
F 39 84 162 M
F 39 84 163 M
F 39 84 160 M
F 39 0115 M
2-17