Body Craft BC-CABLE-PULL User manual

TF
BCCABLEPULL.01.05
BC-CABLE-PULL
~ 60 Min.
CM
Assembly Instructions
Cable Pull Station
L 55 | W 55 | H 206

2
Cable Pull

3
Content
1 GENERAL INFORMATION 6
1.1 Technical Data 6
1.2 Personal Safety 7
1.3 Set-Up Place 8
2 ASSEMBLY 9
2.1 General Instructions 9
2.2 Scope of Delivery 10
2.3 Assembly 12
3 STORAGE AND TRANSPORT 20
3.1 General Instructions 20
4 TROUBLESHOOTING, CARE AND MAINTENANCE 20
4.1 General Instructions 20
4.2 Faults and Fault Diagnosis 20
4.3 Maintenance and Inspection Calendar 21
5 DISPOSAL 21
6 RECOMMENDED ACCESSORIES 22
7 ORDERING SPARE PARTS 23
7.1 Serial Number and Model Name 23
7.2 Parts List 24
7.3 Exploded Drawing 25
8 WARRANTY 26
9 CONTACT 28

4
Cable Pull
Intended Use
The equipment may only be used for its intended purpose.
The equipment is only suitable for home use. The equipment is not suitable for semi-professional
(e.g. hospitals, associations, hotels, schools, etc.) and commercial or professional use (e.g. tness
studios).
Legal Notice
Sport-Tiedje GmbH
Europe’s No. 1 for home tness
International Headquarters
Flensburger Straße 55
24837 Schleswig
Germany
Management:
Christian Grau
Sebastian Campmann
Dr. Bernhard Schenkel
No. HRB 1000 SL
Local Court Flensburg
European VAT Number: DE813211547
Disclaimer
BodyCraft® is a registered brand of the company Fitness Authority Industrial Co., LTD. All rights
reserved. Any use of this trademark without the explicit written permission of Fitness Authority
Industrial Co., LTD is prohibited.
Product and manual are subject to change. Technical data can be changed without advance notice.
Dear customer,
thank you for choosing training equipment of the brand Bodycraft. Bodycraft equipment inspires
with its multifunctionality and excellent quality. In terms of innovation and technology, it is one of
the highest quality tness equipment for home use. Bodycraft multi gyms, for example, oer a very
wide range of exercise possibilities. This ranges from traditional strength training such as bench
presses and rehabilitation exercises to workout for complex sports like golf, tennis or badminton.

5
ABOUT THIS MANUAL
Please carefully read the entire manual before installation and rst use. The manual will help you to
quickly set up the system and explains how to safely use it. Make sure that all persons exercising with
the equipment (especially children and persons with physical, sensory, mental or motor disabilities)
are informed about this manual and its contents in advance. In case of doubt, responsible persons
must supervise the use of the equipment.
This equipment has been manufactured according to the latest safety knowledge.
As far as possible, potential safety hazards which could cause injury have been
eliminated. Make sure to carefully follow the instructions and that all parts are
securely in place. If required, read through the instructions again to correct any
mistakes.
Please pay close attention to the safety and maintenance instructions given here. The contract
partner cannot be held liable for damage to health, accidents or damage to the equipment when it
is not used in accordance with these instructions.
The following safety instructions may appear in this manual:
࣑ATTENTION
This notice indicates potentially hazardous situations which, if not avoided, may result in
property damage.
⚠CAUTION
This notice indicates potentially hazardous situations which, if not avoided, may result in slight
or minor injuries!
⚠WARNING
This notice indicates potentially hazardous situations which, if not avoided, may result in death
or serious injuries!
⚠DANGER
This notice indicates potentially hazardous situations which, if not avoided, will result in death
or serious injuries!
LNOTICE
This notice indicates further useful information.
Retain these instructions in a safe place for future reference, maintenance or when ordering
replacement parts.

6
Cable Pull
1 GENERAL INFORMATION
1.1 Technical Data
Weight and Dimensions
Set-up dimensions (L x W x H) approx.: 55 cm x 55 cm x 206 cm
Package dimensions (L x W x H) and weight approx.:
Box 1: 78 cm x 53 cm x 18 cm 28.2 kg
Box 2: 208 cm x 30 cm x 16 cm 28.5 kg
Box 3: 28 cm x 19 cm x 15 cm 33 kg
Weight block in kg: 67.5 kg
BC-CABLE-PULL-90
Package dimensions (L x W x H) and weight approx.:
Box 1: 78 cm x 53 cm x 18 cm 28.2 kg
Box 2: 208 cm x 30 cm x 16 cm 28.5 kg
Box 3: 28 cm x 19 cm x 15 cm 33 kg
Box 4: 27 cm x 14 cm x 13 cm 23.02 kg
Weight block in kg: 90 kg

7
1.2 Personal Safety
⚠DANGER
+ Before you start using the equipment, you should consult your physician that this type of
exercise is suitable for you from a health perspective. Particularly aected are persons who:
have a hereditary disposition to high blood pressure or heart disease, are over the age of 45,
smoke, have high cholesterol values, are overweight and/or have not exercised regularly in
the past year. If you are under medical treatment that aects your heart rate, medical advice
is absolutely essential.
+ Note that excessive training can seriously endanger your health. Please also note that
heart rate monitoring systems can be inaccurate. If you notice any signs of weakness,
nausea, dizziness, pain, shortness of breath, or other abnormal symptoms, stop exercising
immediately and seek advice from your doctor if necessary.
⚠WARNING
+ This equipment may not be used by children under the age of 14.
+ Children should not be allowed unsupervised access to the equipment.
+ Persons with disabilities must have a medical license and must be under strict observation
when using the equipment.
+ The equipment is strictly for use by one person at a time.
+ If your equipment provides a safety key, the clip of the safety key must be attached to your
clothing before starting your training. In the event of a fall, the EMERGENCY STOP of the
equipment can be initiated.
+ Keep your hands, feet and other body parts, hair, clothing, jewellery and other objects well
clear of moving parts.
+ During use, wear suitable sports clothing rather than loose or baggy clothing.When wearing
sports shoes, make sure they have suitable soles, preferably made of rubber or other non-
slip materials. Shoes with heels, leather soles, studs or spikes are unsuitable. Never exercise
barefoot.
⚠CAUTION
+ If your equipment needs to be connected to the power supply with a mains cable, make
sure that the cable is not a potential tripping hazard.
+ Make sure that nobody is within the range of motion of the equipment during training so as
not to endanger you or other persons.
࣑ATTENTION
+ Do not insert any objects of any kind into the openings of the device.

8
Cable Pull
1.3 Set-Up Place
⚠WARNING
+ Do not place the equipment in main corridors or escape routes.
⚠CAUTION
+ Choose a location in which to place the equipment such that there is enough free space/
clearance to the front, the rear and to the sides of the equipment.
+ The training room should be well ventilated during training and not be exposed to any
draughts.
+ Choose the place in which to set up the equipment such that there is enough free space/
clearance to the front, the rear and to the sides of the equipment.
+ The set-up and mounting surface of the equipment should be at, loadable and solid.
࣑ATTENTION
+ The device may only be used in one building, in suciently tempered and dry rooms
(ambient temperatures between 10°C and 35°C). The equipment should not be used
outdoors or in rooms with high humidity (over 70%) like swimming pools.
+ A oor protective mat/equipment underlay can help to protect high-quality oor coverings
(parquet, laminate, cork, carpets) from dents and sweat and can help to level out slight
unevenness.

9
2 ASSEMBLY
2.1 General Instructions
⚠DANGER
+ Do not leave any tools, packaging materials such as foils or small parts lying around,
as otherwise there is a danger of suocation for children. Keep children away from the
equipment during assembly.
⚠WARNING
+ Pay attention to the instructions attached to the equipment in order to reduce the risk of
injuries.
⚠CAUTION
+ Ensure to have sucient room for movement in each direction during assembly.
+ The assembly of the equipment must be carried out by at least two adults. If in doubt, seek
the help of a third technically skilled person.
࣑ATTENTION
+ To prevent damage to the equipment and the oor, assemble the equipment on a mat or
packaging board.
LNOTICE
+ In order to make the assembly as simple as possible, some screws and nuts to be used can
already be pre-assembled.
+ Ideally, assemble the equipment at its later set-up place.

(1) BASE
FRAME
(7)
CABLE
HE
IGHT
AD
JUSTER
(8) SWIVEL
PULLEY
HOUS ING
(9) DOUBLE
PULLEY
BRACKET
(10) BRACKET
FRAME
(11) SELECTOR
ROD
(12) TOP
PLATE
(19) SELECTOR
PIN
(20) OVAL
END CAP
(21) OVAL
CAP
(22) ROUND
CAP
(28) 5/16" X 2"
HAND SET X 4pcs
(For Wall)
(43) STACK
SPACER
(25) CABLE
(13) WEIGHT
PLATE
(14) RUBBER
DONUT
(15) PLASTIC
GUIDE
ROD HOLDER
(16) PULLEY (17) CLIP
(18) SING
LE
HANDLE
(2) TOP
FRAME
(3) FRONT
UPRIGHT
FRAME
(4) REAR
UPRIGHT
FRAME
(5) GUIDE
ROD
(6) WEIGHT SHROUD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
(1) (2)
(3) (4) (5)
(6)
(7)
(8) (9) (10)
(11)
(12) (13) (14) (15)
(19)
(16) (17) (18)
(20) (21) (22) (28) (43)
(25)
10
Cable Pull
2.2 Scope of Delivery
The scope of delivery consist of the following parts. At the beginning, check whether all parts
and tools belonging to the device are included in the scope of delivery and whether damage has
occurred. In the event of complaints, the contractual partner must be contacted directly.
⚠CAUTION
If parts of the scope of delivery are missing or damaged, the assembly must not be carried out.

29
30
31
32
33
35
36
37
39
40
41
2
4
4
7
2
1
4
4
6
2
13
1/2" X 4-1/4" HEX BOLT
3/8" X 3" HEX BOLT
3/8" X 2-3/4" HEX BOLT
3/8" X 1-3/4" HEX BOLT
3/8" X 1" HEX THREADED BOLT
TOP PLAT E
1/2" WASHER
3/8" SPRING WASHER
3/8" WASHER
1/2" NYLON NUT
3/8" NYLON NUT
29 30
31 32
35 39 40
41
36
33
37
11
Schrauben
No. Name No. Name
1 Base Frame 14 Rubber Donut
2 Top Frame 15 Plastic Guide Rod Holder
3 Front Upright Frame 16 Pulley
4 Rear Upright Frame 17 Clip
5 Guide Rod 18 Single Handle
6 Weight Shroud 19 Selector Pin
7 Cable Height Adjuster 20 Oval End Cap
8 Swivel Pulley Housing 21 Oval Cap
9 Double Pulley Bracket 22 Round Cap
10 Bracket Frame 25 Cable
11 Selector Rod 28 5/16” X 2 Hand Set
12 Top Plate 43 Stack Spacer
13 Weight Plate
Nr. Bezeichnung Anz.
29 1/2" X 4-1/4" Hex Bolt 2
30 3/8" X 3" Hex Bolt 4
31 3/8" X 2-3/4" Hex Bolt 4
32 3/8" X 1-3/4" Hex Bolt 7
33 3/8" X 1" Hex Threaded Bolt 2
35 Top Plate Bolt 1
36 1/2" Washer 4
37 3/8" Spring Washer 4
39 3/8" Washer 6
40 1/2" Nylon Nut 2
41 3/8" Nylon Nut 13

22
22
39
39
40
30
39
30
30
39
20
20
39
40
1
20
20
10
10
30
39
39
41
4
12
Cable Pull
2.3 Assembly
Before assembly, take a close look at the individual assembly steps shown and carry out the assembly
in the order given.
LNOTICE
First loosely screw all parts together and check that they t properly.
Tighten the screws using the tool only when you are instructed to do so.
Step 1: Assemble Base Frame
1. Cap four Oval End Caps (20) to the Base Frame (1). Cap two
Round Caps (22) to the Rear Upright Frame (4).
2. Attach two Bracket Frames (10) to the Rear Upright Frame (4)
using two 3/8” X 3” Hex Bolts (30), four 3/8” Washers (39)
and two 3/8” Nylon Nuts (41).
3. Attach Base Frame (1) to the Rear Upright Frame (4) using
two 3/8” X 3” Hex Bolts (30), three 3/8” Washers (39) and
one 3/8” Nylon Nut (40).
4. Tighten the bolts.

4
1
13
Step 2: Preparation for Wall Mounting
LNOTICE
A hand drill is required for this assembly step. Make sure that you use a suitable drilling
attachment. The contractor is not liable for any damage to the wall.
1. Place the cable pulling station at the desired position
and mark the drill holes.
2. Remove the cable pulling station from the wall and
drill the required holes in the wall with a hand drill.

14
Cable Pull
Step 3: Assembly
1. Attach Front Upright Frame (3) to the Base Frame (1) using two 3/8”X 1”Hex Threaded Bolts (33)
and two 3/8” Spring Washers (37).
2. Attach two Swivel Pulley Housings (8) to the Cable Height Adjuster (7) using two 1/2” X 4-1/4”
Hex Bolts (29), four 1/2”Washres (36), and two 1/2” Nylon Nuts (40).
3. Slide the Cable Height Adjuster (7) over the top of the Rear Upright Frame (3). Stop at your
desired height by locking the Knob (26).
࣑ATTENTION
If you have 19 weight plates, DO NOT install the two spacers (43).
LNOTICE
The whole weight stack consists of the 14 or 19 weight plates with part number 13 and the
upper plate with part number 12. This results in a total of 15 or 20 weight plates.
4. Slide two Stack Spacers (43) and two Rubber Donuts (14) onto one end of each Guide Rod (5)
and then insert Guide Rod (5) into the Plastic Guide Rod Holders (15) in Base Frame (1) as shown.
5. Slide each Weight Plate (13) over Guide Rods (5). Make certain that each plate is oriented with
selector hole on bottom and facing forward.
6. Attach Top Plate (12) to Selector Rod (11) using Top Plate Bolt (35). Slide Top Plate (12) and
Selector Rod (11) over Guide Rods (7).
7. Tighten the bolts.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
4
29
36
7
3
5
5
36
15
14
43
14
15
1
40
29
36
37
37
33
8
19
13
35
11
12
8
40
36
26
15

39 30
39 30
28
28
28
28
15
21
15
41
39
21
2
4
3
33
37 37
16
Cable Pull
Step 4: Assemble Top Frame and Wall Mounting
LNOTICE
If the wall has areas of unevenness, such
as a skirting board, the screws (28)
supplied are not suitable for wall
mounting. In such a case, you need
to purchase a suitable mounting
set of screws yourself.
1. Cap two Oval Caps (21) to the Top
Frame (2). Attach Top Frame (2) to the
Front Uptight Frame (3) using two 3/8”
X 1”Hex Threaded Bolts (33) and two 3/8”
Spring Washers (37).
2. Insert Plastic Guide Rod Holders (15)
into Top Frame (2).
3. Attach Top Frame (2) to the Rear
Upright Frame (4) using 3/8” X 3” Hex
Bolts (30), three 3/8”Washers (39), and one
3/8” Nylon Nut (41).
4. Please use four 5/16”X 2” Hand Sets (28) to
x onto the wall.

(25) CABLE
C4,C6
C8
C4
31
41 9
12
32
41
1
C6
Fig.
1F
ig.2
C1,C9
C2,C3,C5,C7
C1
C2
C9
32
32
32
41
8
8
41
41
31
2
32 41
41
32
41
C3
C5
C7
9
12
11
35
IMPORTANT
17
Step 5: Install Cable
1. Screw the Double Pulley Bracket (9) into the Top Plate (12) with the Selector
Rod (11), see C4 and C6.
࣑ATTENTION
The thread of the Double Pulley Bracket (9) must be screw into the Top Plate
(12) for at least 2 cm.
2. Insert one end of the Cable (25) into the front right side of the Swivel Pulley
Housing (8) and pull it out upwards. Mount two Pulleys with two 3/8“
X 1-3/4“ Hex Bolts (32) und zwei 3/8“ Nylon Nuts (41), see C1 und C9.
3. Run the Cable to the Top Frame (2) over Pulley C2 and C3. Mount Pulley
C2 with a 3/8“ X 1-3/4“ Hex Bolt (32) and a 3/8“ Nylon Nut (41) and
temporarily mount Pulley C3 with a 3/8“ X 2-3/4“ Hex Bolt (31) and a
3/8“ Nylon Nut (41), see C2, C3, C5 and C7.
4. Run the Cable down to the right-hand bracket of the Double Pulley
Bracket (9) and around Pulley C4 (Fig. 1). Temporarily mount Pulley C4
with 3/8“ X 2-3/4“ Hex Bolt (31) and a 3/8“ Nylon Nut (41).
5. Run the Cable to theTop Frame (2) over Pulley C5. Loosen the previously
mounted 3/8“ X 2-3/4“ Hex Bolt (31) and a 3/8“ Nylon Nut (41). Mount
the Pulleys C5 and C3 with the loosened bolt and nut.
6. Run the Cable down and
from behind around Pulley
C6. Loosen the previously
mounted 3/8“ X 2-3/4“ Hex
Bolt (31) and a 3/8“ Nylon
Nut (41). Mount the Pulleys
C6 and C4 with the loosened
bolt and nut.
7. Run the Cable to the Top
Frame (2) and around Pulley
C7. Mount the Pulley C7 with
a 3/8“ X 1-3/4“ Hex Bolt (32)
and a 3/8“ Nylon Nut (41).
8. Run the Cable down and
around Pulley C8. Mount the
Pulley C8 with a 3/8“ X 1-3/4“
Hex Bolt (32) and a 3/8“ Nylon
Nut (41).
9. Run the Cable from there
upwards and from below into
the Swivel Pulley Housing (8).
Mount two Pulleys with two
3/8“ X 1-3/4“ Hex Bolts (32)
und zwei 3/8“ Nylon Nuts
(41), siehe C1 und C9.

C1
C9
C2
C3
C5
C7
C4
C6
C8
18
Cable Pull
LNOTICE
The cable length can be adjusted by removing the Top Plate Bolt (35) to be able
to turn the selector rod (11) and thus retighten the cable or extend
the cable.
10. Tighten the bolts.

34
38
6
6
38
34
38
34
34
38
3834
3438
3438
3834
1
2
19
Step 6: Assemble Weight Shroud
1. Attach Weight Shrouds (6) to Top Frame (2) and Base Frame (1) using eight 5/16” Washers (38)
and eight 5/16” X 1/2” Screws (34). Remember to keep all bolts loose in frame to ensure holes
line up easily.
2. Tighten all bolts.

20
Cable Pull
3 STORAGE AND TRANSPORT
3.1 General Instructions
⚠WARNING
+ The storage location should be chosen so that improper use by third parties or children can
be prevented.
+ If your equipment does not have transportation wheels, the equipment must be
disassembled before transportation.
࣑ATTENTION
+ Make sure that the equipment is protected from moisture, dust and dirt in the selected
storage location. The storage location should be dry and well ventilated and have a constant
ambient temperature between 10°C and 35°C.
4 TROUBLESHOOTING, CARE AND MAINTENANCE
4.1 General Instructions
⚠WARNING
+ Do not make any improper changes to the equipment.
⚠CAUTION
+ Damaged or worn components may aect your safety and the life of the equipment.
Therefore, immediately replace damaged or worn components. In such a case, contact the
contract partner. The equipment must not be used until it has been repaired. If necessary,
use only original spare parts.
࣑ATTENTION
+ In addition to the instructions and recommendations for maintenance and care given here,
additional service and/or repair work may be necessary; this must only be carried out by
authorised service technicians.
4.2 Faults and Fault Diagnosis
The equipment undergoes regular quality controls during production. Nevertheless, faults or
malfunctions may occur. Frequently, individual parts are responsible for these disturbances, an
exchange is usually sucient. Please refer to the following overview for the most common errors and
how to correct them. If the equipment still does not function properly, contact your contract partner.
Fault Cause Solution
Squeaking & cracking
noises
Screw connections loosened
or too tight Check screw connections