Body Craft F715 User manual

Base Lot Number: _ _ _ _ _ _ _ _ _ _ _ _ _
Purchased Date: ___ / ___ / ______
Dealer’s Name:__________________________
Please register your products at:
https://www.bodycraft.com/product-registration/
Open your Camera App
and point it at the QR
Code for additional
information.
http://www.bodycraft.com/
U1000-U1K1-qr.html
Owner’s Manual
1
To see this manual in
FULL COLOR
scan this QR code.
F715 Hold Down / Attachment Kit Option
Open your Camera
App and point it at
the QR Code
Serial Number
Assembled Parts List
F715 v1.4
Part # Assembly Hardware QTY
F715-007 BIG WASHER, φ8 - BLACK 4
F715-008 HEX RECESSED HEAD BOLT, 5/16" x 1-1/4" - BLK 4
F715-009 HEX BOLT, 1/2" x 4-1/4" - BLACK 2
F715-010 NYLON LOCK NUT, 1/2" - BLACK 2
F715-011 FLAT WASHER, 1/2" - BLACK 4
Part # Assembly Parts list QTY
F715-001-ASM LEG WEIGHT HOLDER - Assembly 1
F715-002-ASM ADJUST TUBE - Assembly 1
F715-003 FOAM ROLLER HOLDER 2
F715-004 FOAM ROLLER 4
F715-005 END CAP, LARGER 4
F715-006 END CAP, SMALLER 4
To see in
FULL COLOR
& additional information,
scan this QR code.

TORQUE WRENCH 3/8
DRIVE w/ 7/32 Allen
Product Assembly
Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all
packing materials from your area and place them back into the box. Do not dispose of the packing
materials until assembly is completed.
Read each step carefully before beginning.
SOCKET SET 3/8 DRIVE
WITH 6” EXT for 3/4 SAE
OPEN & CLOSED WRENCH
for 3/4 SAE
ALLEN WRENCH SET
1/16” thu 3/8" SAE
THE FOLLOWING TOOLS ARE RECOMMENDED FOR ASSEMBLY:
STEP 1a: Foam Roller Holders
Insert FOAM ROLLER HOLDERS (3) into the ADJUST
TUBE - Assembly (2-ASM).
STEP 1b: Install Foam Rollers
Slide END CAP, LARGER (5) then the FOAM
ROLLER (4) onto each side of FOAM ROLLER
HOLDERS (3), one bar post at a time.
NOTE: Confirm centered with equal distance on
both Right & Left Sides.
STEP 1c: Secure Foam Rollers
Then slide a HEX RECESSED HEAD BOLT, 5/16" x 1-1/4" (8) through the END CAP, SMALLER (6)
and the BIG WASHER, φ8 (7). Hand tighten at this time with an 7/32 Allen Wrench.
2
TORQUE WRENCH 3/8
DRIVE w/ 7/32 Allen

Product Assembly
STEP 2a: Adjustment Tube Holder
Insert the preassembled ADJUST TUBE -
Assembly (2-ASM) from STEPS 1a-c, by pulling
out on the PULL-PIN LOCKING KNOB (13) and
slowly lowering onto the LEG WEIGHT HOLDER
- Assembly (1-ASM).
STEP 2b: Install Hold Down / Attachment Kit
Option
Attach the HOLD DOWN / ATTACHMENT KIT (F715)
to a BodyCraft bench of choice, either an F601, F605,
F705 or F708. Use the following hardware:
● Two HEX BOLTS, 1/2" x 4-1/4" (9)
● Four FLAT WASHER, 1/2" (11)
● Two NYLON LOCK NUT, 1/2" (10)
STEP 2c: “Torque Time”
Tighten all Bolts at this time to the Recommended
Torque Specs, as shown in the diagram to the right.
4 ft-lbs
(+/- 1 lbs)
20 ft-lbs
(+/- 2 lbs)
3
TIP: PULL-PIN LOCKING KNOB Instructions
3/4 SOCKET &
6” EXTENSION
3/4 WRENCHES
Recommended Tools
TORQUE WRENCH 3/8 DRIVE w/ 3/4 Socket & 7/32 Allen
Recommended Tools

Detailed Parts List & Parts Exploded View
Product Assembly
STEP 3: Installation Example
Remove handle from bench, then Install the preassembled Hold Down / Attachment Kit to a
BodyCraft bench.
9/16 SOCKET &
6” EXTENSION
9/16 WRENCHES
Parts Exploded View
4
Part # Detailed Parts list QTY
F715-001 LEG WEIGHT HOLDER 1
F715-002 ADJUST TUBE 1
F715-003 FOAM ROLLER HOLDER 2
F715-004 FOAM ROLLER 4
F715-005 END CAP, LARGER 4
F715-006 END CAP, SMALLER 4
F715-007 BIG WASHER, φ8 - BLACK 4
F715-008 HEX RECESSED HEAD BOLT, 5/16" x 1-1/4" - BLK 4
F715-009 HEX BOLT, 1/2" x 4-1/4" - BLACK 2
F715-010 NYLON LOCK NUT, 1/2" - BLACK 2
F715-011 FLAT WASHER, 1/2" - BLACK 4
F715-012 BRACKET, SMALL RUBBER 1
F715-013 PULL-PIN LOCKING KNOB 1
F715-014 SPACE CAP 1
F715-015 END PLUG, RECT. 1
F715-016 END PLUG, 45 x 45mm SQ. 2