Body Craft MB1602 User manual

Serial Number Location
Record your Serial number
and purchase date here:
S/N __________________
PURCH.DATE:_________
DEALER:______________
______________________
______________________
SERIAL
12345678
CABLE PULL STATION
OWNER'S MANUAL
Recreation Supply Inc.
7699 Green Meadows Drive
Lewis Center, OH 43035
Model No. CABLE PULL STATION
MB1602
BODYCRAFT is a division of Recreation Supply

Congratulations and Thank You!
Important Safety Notes
1
Thank you for selecting the BODYCRAFT Cable Pull Station.
The BODYCRAFT CPS offers an impressive array of strength training
exercises to develop every major muscle group of the body. Whether your
goal is cardiovascular fitness, a shapely, toned body or dramatic muscle size
and strength, the BODYCRAFT CPS will help you achieve the results you want.
For your safety and benefit, read this manual and the accompanying literature
before using the BODYCRAFT CPS. Keep this manual for future reference.
If you have additional questions, please call your local BODYCRAFT Elite
Dealer or our customer service department at 800-990-5556 Monday through
Friday, 9 am until 5 pm Eastern Standard Time.
There is a risk assumed by individuals who use this type of equipment.
Before beginning this or any other exercise program consult your physician.
This is especially important for individuals over the age of 35 or persons
with preexisting health problems. Fitness Authority Industrial Co,. Ltd.
assumes no responsibility for personal injury or property damage sustained
by or through use of this product.
1. This product must be assembled on a flat, level surface to assure its proper function.
2. Clean pads and frame on a regular basis. We recommend warm, soapy water.
Do not use harsh or abrasive chemicals.
3. Inspect and tighten all parts before every use. Replace any worn
parts immediately. Failure to do so may result in serious injury.
4. Keep children away from the BODYCRAFT CPS at all times.
5. Keep your hands away from cables and pulleys during operation.
6. Keep your hands away from moving parts other than the designated handles.
7. When adjusting the seat, make sure the spring pin is fully engaged.
If not, the seat may slip and cause serious injury.
8. Make certain all cables are seated within the pulleys before every use.
9. Exercise with care to avoid injury.
10. If you are unsure about the proper use of the BODYCRAFT Cable Pull Station call
your local BODYCRAFT dealer or our customer service department.
QUESTIONS?
As a quality home gym supplier we are committed to your complete satisfaction.
If you have questions, or find missing or damaged parts, we will guarantee your
complete satisfaction through our authorized dealer service centers or our home
office customer service department. Please call your local dealer for assistance
or BODYCRAFT at 800-990-5556 (9 AM - 5 PM) EST. Our trained technicians
will provide immediate assistance to you, free of charge.

Gym Placement Planner
Important Notes and Tips:
Ratchet
9/16" Socket
3/4" Socket
9/16" Combination Wrench
3/4" Combination Wrench
Adjustable Wrench
Rubber Mallet
Metric Allen Key Set
2
WALL
Recommended Tools
for Assembly
1. Do not tighten any bolts until instructed.
2. Two people are reguired for the safe assembly
of the gym.
3. Use silicone lubricant on guide rods prior to weight
plate installation.
4. Carefully install plastic caps using a rubber mallet.
5. For your convenience, rulers are displayed throughout
this manual.
6. When measuring bolt lengths, only measure the shank.
i.e. 2-1/4" Hex Bolt
01/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/41" 2" 3"
HEIGHT
79.8"
21.1"
23.9"

CPS Parts List 1
NOTE: IF A PART IS MISSING, IT LIKELY HAS BEEN PRE-INSTALLED FOR
QUALITY CONTROL PURPOSES. PLEASE PROCEED WITH ASSEMBLY.
NOTE: THIS IS A WALL MOUNT MACHINE. IT REQUIRE ELECTRIC DRILL
MACHINE, AND IT IS EXCLUDED FROM THIS GYM EQUIPMENT.
(1) BASE
FRAME
(7) CABLE
HEIGHT
ADJUSTER
(8) SWIVEL
PULLEY
HOUSING
(9) DOUBLE
PULLEY
BRACKET
(10) BRACKET
FRAME
(11) SELECTOR
ROD
(12) TOP
PLATE
(19) SELECTOR
PIN
(20) OVAL
END CAP
(21) OVAL
CAP
(22) ROUND
CAP
(28) 5/16" X 2"
HAND SET X 4pcs
(For Wall)
(43) STACK
SPACER
(25) CABLE
(13) WEIGHT
PLATE
(14) RUBBER
DONUT
(15) PLASTIC
GUIDE
ROD HOLDER
(16) PULLEY (17) CLIP
(18) SINGLE
HANDLE
(2) TOP
FRAME
(3) FRONT
UPRIGHT
FRAME
(4) REAR
UPRIGHT
FRAME
(5) GUIDE
ROD
(6) WEIGHT SHROUD
3
*Parts images are not to scale.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
(44) ANKLE
STRAP

29
30
31
32
33
35
36
37
39
40
41
2
4
4
7
4
1
4
4
10
2
13
1/2" X 4-1/4" HEX BOLT
3/8" X 3" HEX BOLT
3/8" X 2-3/4" HEX BOLT
3/8" X 1-3/4" HEX BOLT
3/8" X 1" HEX THREADED BOLT
TOP PLATE BOLT
1/2" WASHER
3/8" SPRING WASHER
3/8" SEMICIRCLE WASHER
1/2" NYLON NUT
3/8" NYLON NUT
CPS Parts List 2
NO. DESCRIPTION QTY.
4
NOTE: IF YOU SEEM TO BE MISSING A PART, DO NOT WORRY, IT
LIKELY HAS BEEN PRE-INSTALLED FOR QUALITY CONTROL PURPOSES.
29 30
31 32
35 39 40
41
36
33
37
01/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/41" 2" 3" 4" 1/4 1/2 3/4 1/4 1/2 3/45" 6"
(inch)

STEP 1 Install Onto The Wall
5
1. Cap four Oval End Caps (20) to the
Base Frame (1). Cap two Round Caps
(22) to the Rear Upright Frame (4).
2. Attach two Bracket Frames (10) to the
Rear Upright Frame (4) using two 3/8"
X 3" Hex Bolts (30), four 3/8"
Semicircle Washers (39) and two 3/8"
Nylon Nuts (41).
3. Attach Base Frame (1) to the Rear
Upright Frame (4) using two 3/8" X 2-
3/4" Hex Bolts (31), three 3/8"
Semicircle Washers (39) and one 3/8"
Nylon Nut (40). Tighten the bolts.
NOTE: WALL MOUNT TOOLS ARE REQUIRED. DO NOT TIGHTEN BOLTS
UNLESS INSTRUCTED.
22
22
39
39
40
31
39
31
30
39
20
20
39
40
1
20
20
10
10
30
39
39
41
4

4
1. Please drill the hole on the
wall using the Electric Hand
Drill Machine as show in
below.
STEP 2 Assemble Base Frame
6
1

STEP 3 Assemble Base Frame
7
1. Attach Front Upright Frame (3) to the Base Frame (1) using two
3/8" X 1" Hex Threaded Bolts (33) and two 3/8" Spring Washers
(37).
2. Attach two Swivel Pulley Housings (8) to the Cable Height
Adjuster (7) using two 1/2" X 4-1/4" Hex Bolts (29), four 1/2"
Washres (36), and two 1/2" Nylon Nuts (40). Slide the Cable
Height Adjuster (7) over the top of the Rear Upright Frame (3).
Stop at your desired height by locking the Knob (26).
3. Slide two Stack Spacers (43) and two Rubber Donuts (14) onto
one end of each Guide Rod (5) and then insert Guide Rod (5)
into the Plastic Guide Rod Holders (15) in Base Frame (1) as
shown.
4. Slide each Weight Plate (13) over Guide Rods (5). Make certain
that each plate is oriented with selector hole on bottom and
facing forward. Attach Top Plate (12) to Selector Rod (11) using
Top Plate Bolt (35). Slide Top Plate (12) and Selector Rod (11)
over Guide Rods (7). Tighten the bolts.
NOTE: If you have purchase 19 piece of Weight Plate (13).
Please DO NOT install Stack Spacers (43) on the follow step.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
4
STEP 3 Assemble Base Frame
8
29
36
7
3
5
5
36
15
14
43
14
15
1
40
29
36
37
37
33
8
19
13
35
11
12
8
40
36
26

39
31
39 31
28
28
28
28
STEP 4 Assemble Top Frame
9
15
21
15
41
39
21
2
4
3
33
37 37
1. Cap two Oval Caps (21) to the Top
Frame (2). Insert Plastic Guide Rod
Holders (15) into Top Frame (2).
2. Attach Top Frame (2) to the Front
Uptight Frame (3) using two 3/8" X
1" Hex Threaded Bolts (33) and two
3/8" Spring Washers (37).
3. Attach Top Frame (2) to the Rear
Upright Frame (4) using 3/8" X 2-
3/4" Hex Bolts (31), three 3/8"
Washers (39), and one 3/8" Nylon
Nut (41).
4. Please use four 5/16" X 2" Hand
Sets (28) to fix onto the wall.

10
STEP 5 Install Cable
C1
C9
C2
C3
C5
C7
C4
C6
C8
C4,C6
C8
C4
30
41 9
12
32
41
1
C6
(25) CABLE
1. Screw the Double Pulley Bracket (9) into the Top Plate (12) with
Selector Rod (11) 10 threads (2cm). As Show in C4,C6.
2. Insert the ball end of the Cable (25) into the front of the right side
Swivel Pulley Housing (8) and come out from top. Then attach two
pulleys as shown in C1,C9.
3. Route cable up to Top Frame (2) and along to down to left side pulley
in Double Pulley Bracket (9) next pulley over pulley mounted as
shown in C2,C3,C5,C7.
4. Coutinue along Top Frame (2) to next pulley. Then down to left side
pulley in Double Pulley Bracket (9) as shown in Fig 1. up to rear side
of next pulley in Top Frame (2), then up to
front of last pulley in Top Frame (2) as shown
in Fig 2.
5. Route cable over last pulley in top, exiting
toward rear, continue down to pulley
mounted behind Base Frame (1) as shown in
C8, under Weight Stack, and around pulley
at base next to column. Finally, route cable
up to left side of Swivel Pulley Housing (8)
and mount pulleys as shown in C1,C9.
IMPORTANT: Cable length can be
adjusted by removing the Bolt on the
Top Plate (12) to turn the Selector Rod
(11) to remove slack or further down to
gain length. Fig.1 Fig.2
C1,C9
C2,C3,C5,C7
C1
C2
C9
32
32
32
41
8
8
41
41
30
2
32 41
41
32
41
C3
C5
C7
9
12
11
35
IMPORTANT

11
STEP 6 Assemble Weight Shroud
34
38
6
6
38
34
38
34
34
38
3834
3438
3438
3834
1
2
1. Attach Weight Shrouds (6) to Top
Frame (2) and Base Frame (1) using
eight 5/16" Washers (38) and eight
5/16" X 1/2" Screws (34). Remember
to keep all bolts loose in frame to
ensure holes line up easily. Tighten all
bolts.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
OVERVIEW
12
29
22
24
6
3
27
36
40
41
5
7
5
41
16 10
28
28
28
39
30
39
39
31
41
41
44
16
16 32
32
41
32
25
17
18
8
8
41
16
25
3834
34
3834
17
18
16
41
30
35
19
20
20
20
32
41
16
20 38 34
1
41
30
21
26
32
13
16
39
39
41
10 39
30
39
41
31
39
3438
31
31
22
39
39
41
11
14
43
15
14
43
15
37
33
12
38
34
38
34
4
6
9
42
33
2
37
21
16 16
32
41
16
15
29
27
23
34
38
38
36
40
36
27
36
27
23 15

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
1
1
1
1
2
2
1
2
1
2
1
1
14
2
4
11
2
2
1
4
2
2
2
1
1
1
4
4
2
4
4
7
4
8
1
4
4
8
10
2
13
1
2
1
BASE FRAME
TOP FRAME
FRONT UPRIGHT FRAME
REAR UPRIGHT FRAME
GUIDE ROD
WEIGHT SHROUD
CABLE HEIGHT ADJUSTER
SWIVEL PULLEY HOUSING
DOUBLE PULLEY BRACKET
BRACKET FRAME
SELECTOR ROD
TOP PLATE
WEIGHT PLATE
RUBBER DONUT
PLASIC GUIDE ROD HOLDER
PULLEY
CLIP
SINGLE HANDLE
SELECTOR PIN
OVAL END CAP
OVAL CAP
ROUND CAP
HOLLOW
HANDLE GRIP
CABLE
KNOB
BUSHING
5/16" X 2" HAND SET (For Wall)
1/2" X 4-1/4" HEX BOLT
3/8" X 3" HEX BOLT
3/8" X 2-3/4" HEX BOLT
3/8" X 1-3/4" HEX BOLT
3/8" X 1" HEX THREADED BOLT
5/16 X 1/2" SCREW
TOP PLATE BOLT
1/2" WASHER
3/8" SPRING WASHER
5/16" WASHER
3/8" SEMICIRCLE WASHER
1/2" NYLON NUT
3/8" NYLON NUT
1/2" NUT
STACK SPACER
ANKLE STRAP
NO. DESCRIPTION QTY.
13
1
3 4 5 6
2
7
8
9 10
11
12 13
16 17
18
19 20 21 22 23 24
25
26 27 28 29
30 31 32
33 34 35 39
40 41 42 43 44
36 3837
14 15
COMPLETE PARTS CHART
*Parts images are not to scale.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Assembly is complete! Please take the following steps before using the gym:
1.
2.
3.
4.
5.
6.
7.
Make certain all bolts are tightened securely.
Make certain all cables are seated into all pulley grooves. A cable rubbing
against steel will peel the nylon coating, voiding warranty and resulting in
a need for replacement.
Pre-stretch the cables. Put the Weight Selector Pin (19) in the bottom hole on
the weight stack. Pull on the cables with great force, helping remove any kinks
and providing any initial cable stretch.
Be aware the cables can loosen and slightly stretch upon initial use.
The cables should be adjusted as tight as possible, but no so tight as to lift the
Top Plate (12) above the weight stack. Be certain to secure the jam nuts after
adjustments are made.
For better performance, apply a household lubricant (such as silicone) to
any adjustable areas and to the Guide Rods (5).
Enjoy many years of a Fit Lifestyle.
Thank you for purchasing the BodyCraft Cable Pull Station.
If you have any questions, please call your local BodyCraft
dealer, call our customer service department at 800-990-5556
or at http://www.bodycraft.com.