Body Craft Jones Platinum User manual

Jones Platinum Strength Training System
OWNERS MANUAL
MA9051A Recreation Supply Inc.
Model No. Jones Platinum 7699 Green Meadows Dr
BODYCRAFT is a division of Recreation Supply Lewis Center, OH 43035
Rev. 04/17

1
Congratulations and Thank You!
Important Safety Notes
Parts Missing or Damaged?
Thank you for selecting the BODYCRAFT Jones Platinum Strength Training
System. The BODYCRAFT Jones Platinum offers an impressive array of
strength training exercises to develop every major muscle group of the body.
Whether your goal is cardiovascular fitness, a shapely, toned body or dramatic
muscle size and strength, the BODYCRAFT Jones Platinum will help you
achieve the results you want. For your safety and benefit, read this manual
and the accompanying literature before using the BODYCRAFT Jones
Platinum. Keep this manual for future reference. If you have additional
questions, please contact your local BODYCRAFT Jones Platinum Dealer or
BODYCRAFT at [email protected] or 800-990-5556 Monday - Friday, 9 am
until 5 pm EST.
There is a risk assumed by individuals who use this type of equipment.
Before beginning this or any other exercise program consult your physician.
This is especially important for individuals over the age of 35 or persons
with preexisting health problems. BODYCRAFT assumes no responsibility for
personal injury or property damage sustained
by or through use of this product.
1. This product must be assembled on a flat, level surface to assure its proper function.
2. Clean pads and frame on a regular basis. We recommend warm, soapy water.
Do not use harsh or abrasive chemicals.
3. Inspect and tighten all parts before every use. Replace any worn
parts immediately. Failure to do so may result in serious injury.
4. Keep children away from the BODYCRAFT Jones Platinum at all times.
5. Keep your hands away from cables and pulleys during operation.
6. Keep your hands away from moving parts other than the designated handles.
7. When locking the fore and aft adjustment, make sure the locking lever is fully
engaged. If not, the mechanism may release and cause serious injury.
8. Make certain all cables are seated within the pulleys before every use.
9. Exercise with care to avoid injury.
10. If you are unsure about the proper use of the BODYCRAFT Jones Platinum call your
local BODYCRAFT dealer or our customer service department.
As a quality home gym supplier we are committed to your complete satisfaction.
If you find missing or damaged parts, we will guarantee your complete
satisfaction through our authorized dealer service centers or our home office
customer service department. Please contact your local dealer for assistance or
BODYCRAFT at [email protected] or 800-990-5556 (9 AM - 5 PM) EST.
Our trained technicians will provide immediate assistance to you.

Important Notes and Tips:
Ratchet
9/16" Socket
3/4" Socket
9/16" Combination Wrench
3/4" Combination Wrench
Adjustable Wrench
Rubber Mallet
Metric Allen Key Set
2
Recommended Tools
for Assembly
1. Do not tighten any bolts until instructed.
2. Two people are required for the safe assembly
of the gym.
3. Use silicone lubricant on guide rods prior to weight
plate installation.
4. Carefully install plastic caps using a rubber mallet.
5. For your convenience, rulers are displayed throughout
this manual.
6. When measuring bolt lengths, only measure the shank.
i.e. 2-1/4" Hex Bolt
01/4 1/2 3/4 1" 1/4 1/2 3/4 2" 1/4 1/2 3/4 3" 1/4
Gym Placement Planner
WALL
HEIGHT
83.5"
59”
Base Frame
84”
with Bar
62” Base
20”* with Full Body Trainer
(FBT) Option*
82”*
* Use this measurement if you have purchased the optional FBT (full body trainer).

1
2L
3R
3L
4R
4L
5
6
7R
7L
8
9
10
11
12
13
14R
14L
15
16R
16L
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
2
1
1
1
1
1
2
2
2
2
1
1
1
4
2
2
1
1
2
1
1
2
2
2
4
2
2
2
4
2
2
2
2
2
4
2
2
4
4
6
2
4
BASE FRAME
REAR BASE FRAME CONNECTOR
RIGHT UPRIGHT FRAME
LEFT UPRIGHT FRAME
RIGHT BAR RACK
LEFT BAR RACK
VERTICAL GUIDE ROD
HORIZONTAL GUIDE ROD
(pre-assembled in Base Frame)
RIGHT WEIGHT SHROUD
LEFT WEIGHT SHROUD
POWER BAR
TOP FRAME
CHROMED CHIN UP BAR
BASE FRAME END PLATE
STEEL PLATE
VERTICAL BEARING HOUSING
RIGHT SAFETY CATCH
(pre-assembled at factory)
LEFT SAFETY CATCH
(pre-assembled at factory)
SAFETY SPOTTER
RIGHT BEARING JOINT
LEFT BEARING JOINT
FOOT LOCKING HINGE
1/2" AXLE (w/12mm)
1/2" AXLE (w/3/8")
HOOK PLATE
(pre-assembled with Safety Spotter)
LINK PLATE
(pre-assembled on Weight Bar)
OLYMPIC WEIGHT SLEEVE
19 X 13 X 70L CONNECT ROD
(pre-assembled on Weight Bar)
34 X 29 X 8L SPACER
19 X 13 X 15L SHORT CONNECT
ROD (pre-assembled on Safety Spotter)
1" ID BIG WASHER
1" SPRING
2" OLYMPIC SPRING CLIP
1/2" SPRING
1-1/8" BUSHING (pre-assembled in Safety Spotter)
HANDLE FRAME STOPPER
STOPPER (pre-assembled in Safety Spotter)
RUBBER STOPPER
(pre-assembled in Base Frame)
30mm BEARING (pre-assembled in Base Frame)
60/28 BEARING
(pre-assembled in Base Frame)
10mm BEARING
25mm BEARING
(pre-assembled in Vert., Top Bearing Housings)
26
PARTS LIST
NO. DESCRIPTION QTY.
01/4 1/2 3/4 1" 1/4 1/2 3/4 2" 1/4 1/2 3/4 3" 1/4 1/2 3/4 4" 1/4 1/2 3/4 5" 1/4 1/2 3/4 6"
(inch)
3
12L
3R 3L
4R 4L 5
6
7R 7L
8 9 10
11 12 13 14R 14L 15
16R 16L 17 18 19 20 21
2322
3433
27 28 29
30
24 25
31 32 35 36 37

38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
4
4
2
8
2
12
8
2
10
18
2
16
2
2
2
2
16
2
10
16
54
4
16
22
6
4
2
4
26
4
4
2
4
4
SHORTER TRIM OF SHROUD
LONGER TRIM OF SHROUD
1/2" X 3" HEX THREADED BOLT
1/2" X 1" HEX THREADED BOLT
1/2" X 1-3/4" HEX THREADED BOLT
3/8" X 2-3/4" HEX BOLT
3/8" X 1-1/4" HEX BOLT
3/8" X 1-1/4" INNER HEX SCREW
3/8" X 1" INNER HEX SCREW
3/8" X 5/8" INNER HEX SCREW
PLASTIC KNOB
5/16" X 1/2" INNER HEX SCREW
5/8" X 1-1/4" ALLEN BOLT
3/8" X 1/2" INNER HEX BOLT
5/16" X 3/4" ALLEN BOLT
5/16" X 1-1/4" COUNTER
ALLEN BOLT
M8 X 16 COUNTER ALLEN BOLT
5/16" X 5/8" SET SCREW
5/16" X 1/4" SET SCREW
1/2" WASHER
3/8" WASHER
M12 WASHER
5/16" WASHER
3/8" SPRING WASHER
R52 RETAINING RING
(pre-assembled in Weight Bar)
R40 RETAINING RING
(pre-assembled in Vert Bearing Housings)
R35 RETAINING RING
1/2" NYLON NUT
3/8" NYLON NUT
M12 NYLON NUT
MAGNET
3/8" NUT
LONGER NON-SLIP STRIP
SHORTER NON-SLIP STRIP
PARTS LIST
NO. DESCRIPTION QTY.
01/4 1/2 3/4 1" 1/4 1/2 3/4 2" 1/4 1/2 3/4 3" 1/4 1/2 3/4 4" 1/4 1/2 3/4 5" 1/4 1/2 3/4 6"
(inch)
4
38 39
41
4540
46 51
47
5348
54
55 56 57 58 59 60
61 62 63
65 66 67 68 69
70 71
50
52
43
42
44 49
64

STEP 1 Base Frame Assembly
5
1. Attach the REAR BASE FRAME CONNECTOR (2L) to the
BASE FRAME (1), using four 3/8" X 1 INNER HEX SCREWS (46) and
four 3/8" WASHERS (58).
2. Attach four BASE FRAME END PLATES (11) to the front and rear of the
BASE FRAME (1), using eight 1/2" X 1" HEX BOLTS (41) and eight 1/2"
WASHERS (57).
41
41
57
57 11
11
1
/ I
58
58
58
58
46
46
57
11
57
41 11
1
41
01/4 1/2 3/4 1" 1/4 1/2 3/4 2" 1/4 1/2 3/4 3" 1/4 1/2 3/4 4" 1/4 1/2 3/4 5" 1/4 1/2 3/4 6"
(inch)
TO EASE THE ASSEMBLY PROCESS.
DO NOT TIGHTEN ANY BOLTS UNTIL INSTRUCTED.

STEP 2 Right & Left Upright Frame Assembly
6
1. Attach the RIGHT UPRIGHT (3R) to the holes of plate on the BASE
FRAME (1), using five 3/8" X 5/8" INNER HEX SCREWS (47), and five
3/8" WASHERS (61). Please move the BEARING HOUSING (12) to see
the moving smoothly before the Screws tighten.
2. Please follow the same procedure for the LEFT UPRIGHT (3L).
47
47
47
47
47
47
61 61
61
61
61
61 61
61
61
61
1
1
12
0
0 I
01/4 1/2 3/4 1" 1/4 1/2 3/4 2" 1/4 1/2 3/4 3" 1/4 1/2 3/4 4" 1/4 1/2 3/4 5" 1/4 1/2 3/4 6"
(inch)
12

STEP 3 Top Frame Assembly
7
1. Attach TOP FRAME (9) to the RIGHT UPRIGHT FRAME (3R) and LEFT
UPRIGHT FRAME (3L) and align the holes, using eight 3/8" X 5/8" INNER HEX
SCREWS (47), ten 3/8" SPRING WASHERS (61) and two 3/8" NYLON NUTS
(66).
47 47
47
61
61
61
66
47
47
61
61
9
0
0 I
61
66

STEP 4 Right & Left Bar Rack Assembly
8
1. Attach RIGHT BAR RACK (4R) to the RIGHT UPRIGHT (3R), using six 3/8" X 2-
3/4" HEX BOLTS (43), twelve 3/8" WASHERS (58) and six 3/8" NYLON NUTS
(66).
2. Please follow the same procedure for the LEFT BAR RACK (4L).
43 58
0
58 66
58 66
58 66
58 66
58 66
58
58
56
56
58 43
58
58 43
58 43
58 43
58
0 I
43
43
56
66
58
66
58
66
58
66
58
66
58
66
66
1O
1I
56
43 58
43 58
43 58
43 58
43 58

1. To ease the assembly of ACTIVE BALANCE BAR (8), slide
one end of BAR (8) through the gap of RIGHT UPRIGHT (3R)
and insert the other end of BAR (8) through the gap of LEFT
UPRIGHT (3L) as figure shown A,B,C,D.
2. Slide a VERTICAL BEARING HOUSING (13) up to match up
with the RIGHT & LEFT SAFETY CATCH (14R,14L). Bolt the
VERTICAL BEARING HOUSING (13) to the SAFETY CATCH
(14) using eight 3/8" X 1-1/4" HEX BOLTS (44), eight 3/8"
WASHERS (58), and eight 3/8" NYLON NUTS (66).
Tighten these bolts.
The views of the Jones below are reversed.
Confirm the bar orientation before proceeding.
9
STEP 5 ABB Bar Assembly*
44
58
13
13
14L
14R
58
58
58
8
66
66
58
58
58
44
58
FRONT
FRONT
FRONT
FRONT
FRONT
*If you have purchased the Power Bar instead of the Active Balance bar, the
assembly will differ. Use the instructions included in the box of the Power Bar.
A
B
CD

STEP 6 Right & Left Weight Shroud Assembly
10
1. Attach Right WEIGHT SHROUD (7R) to the RIGHT
UPRIGHT (3R), using four 5/16" X 1/2" INNER HEX
BOLTS (49), four 5/16" X 1" INNER HEX
SCREWS (48) and eight 5/16" WASHERS (60).
2, Please do the same procedures.
4I
39
38
49
49 60
60
4
60 49
49
49
49
49
49
49
49
49
60
60
4
60
60
39
38
0
0 I
49
49
49
60
60
60
38
39
60
4I
60
38 39 60
60
49
49
60 60
01/4 1/2 3/4 1" 1/4 1/2 3/4 2" 1/4 1/2 3/4 3" 1/4 1/2 3/4 4" 1/4 1/2 3/4 5" 1/4 1/2 3/4 6"
(inch)

Assembly is complete! Please take the following steps before using the
BODYCRAFT SMITH STRENGTH TRAINING SYSTEM:
1. Make certain all bolts are tightened securely.
2. For better performance, apply a household lubricant (such as silicone)
3.
4.
to VERTICAL GUIDE RODS(5).
Always be certain that SAFETY SPOTTERS(15) are fully engaged when
using spotters.
Enjoy many years of a Fit Lifestyle.
Thank you for purchasing the Jones Platinum System. If You have
any questions, please call your local BodyCraft dealer or call our
customer service department at 800-990-5556