Body Solid GDIB46L Quick start guide

&
Assembly Instructions
O W N E R ’ S M A N U A L
by
by
®
®
v. 110810
by
by
®
®
GDIB-46L
T able of Contents
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . p. 2
Reference Drawings. . . . . . . . . . . . . . . . . . . p. 3
Important Safety Instructions. . . . . . . . . . . p. 4
Before You Begin. . . . . . . . . . . . . . . . . . . . . . p. 5
Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . p. 6
Assembly Instructions. . . . . . . . . . . . . . . . . p. 7-13
Warning, Safety & Maintenance. . . . . . . . . p. 14-17
Mainframe Parts List. . . . . . . . . . . . . . . . . . . p. 18
Hardware List. . . . . . . . . . . . . . . . . . . . . . . . . p. 19
Hardware (To Scale). . . . . . . . . . . . . . . . . . . p. 20-21
Exploded View Diagram. . . . . . . . . . . . . . . . p. 22
Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 23
GDIB-46L
VERSION 1110

Dimensions
2
The room layout diagram below will help you decide
the best placement for your GDIB-46L.
The overall space needed for operation may be more depending on the user.
Minimum Usage Space – 3’ 10”W x 4’ 8” L x 4’ 4” H
Suggested Usage Space – 6’W x 6’ 8” L
D i m e n s i o n s
4'8" 3'10"
4'4"
6' 6'8"
Dimensions Height
Suggested usage space
The room layout diagram below will help you decide the best placement for your GDIB-46L.
The dimensions of the GDIB-46L are: Width 3'10" X Length 4'8". The ceiling height requirement for the GDIB-46L is 4'4".
The usage space is: Width 6" X Length 6'8" (The usage space is the overall space needed for operation).
The usage space needed for the GDIB-46L could be more, depending on the user.
D i m e n s i o n s
4'8" 3'10"
4'4"
6' 6'8"
Dimensions Height
Suggested usage space
The room layout diagram below will help you decide the best placement for your GDIB-46L.
The dimensions of the GDIB-46L are: Width 3'10" X Length 4'8". The ceiling height requirement for the GDIB-46L is 4'4".
The usage space is: Width 6" X Length 6'8" (The usage space is the overall space needed for operation).
The usage space needed for the GDIB-46L could be more, depending on the user.
D i m e n s i o n s
4'8" 3'10"
4'4"
6' 6'8"
Dimensions Height
Suggested usage space
The room layout diagram below will help you decide the best placement for your GDIB-46L.
The dimensions of the GDIB-46L are: Width 3'10" X Length 4'8". The ceiling height requirement for the GDIB-46L is 4'4".
The usage space is: Width 6" X Length 6'8" (The usage space is the overall space needed for operation).
The usage space needed for the GDIB-46L could be more, depending on the user.

3
Reference Drawings
by
by
®
®
Use the following diagrams as a point of reference when
assembling your GDIB-46L.
Becoming familiar with the unit and the orientation of its components will help ease installation. Please
use the following diagrams to become more accustomed with your GDIB-46L and its applications.
G D I B - 4 6 L
R e f e r e n c e D r a w i n g s
G D I B - 4 6 L
R e f e r e n c e D r a w i n g s
G D I B - 4 6 L
R e f e r e n c e D r a w i n g s
G D I B - 4 6 L
R e f e r e n c e D r a w i n g s

Important Safety Instructions
4
Before beginning any tness program, you should obtain
a complete physical examination from your physician.
Il est conseille de subir un examen medical complet avant d’entreprendre tout programme d’exercise. Si vous avez
des etourdissements ou des faiblesses, arretez les exercices immediatement.
Antes de comenzar cualquier programma de ejercicios, deberias tener un examen sico con su doctor.
Whenusingexerciseequipment,youshould
always take basic precautions, including
the following:
Read all instructions before using the GDIB-46L.
These instructions are written to ensure your safety
and to protect the unit.
Do not allow children on or near the equipment.
Use the equipment only for its intended purpose as
described in this guide. Do not use accessory attach-
ments that are not recommended by the manufac-
turer. Such attachments might cause injuries.
Wear proper exercise clothing and shoes for your
workout, no loose clothing.
Use care when getting on or o the unit.
Do not overexert yourself or work to exhaustion.
If you feel any pain or abnormal symptoms, stop
your workout immediately and consult your physi-
cian.
Never operate the unit when it has been dropped or
damaged. Return the equipment to a service center
for examination and repair.
Never drop or insert objects into any opening in the
equipment.
Always check the unit before each use. Make sure
that all fasteners are secure and in good working
condition.
Do not use the equipment outdoors or near water.
Personal Safety During Assembly
It is strongly recommended that a qualied dealer
assemble the equipment.
Assistance is required.
Before beginning assembly, please take the time to
read the instructions thoroughly.
Read each step in the assembly instructions and
follow the steps in sequence. Do not skip ahead. If
you skip ahead, you may learn later that you have
to disassemble components and that you may have
damaged the equipment.
Assemble and operate the GDIB-46L on a solid, level
surface. Locate the unit a few feet from the walls or
furniture to provide easy access.
 m
 m
 m
 m
 m
 m
 m
 m
 m
 m
 m
 m
 m
 m
 m

5
B e f o r e Y o u B e g i n
Retain this Owner’s Manual for future reference!
To maximize your use of the equipment please study this Owner’s Manual thoroughly. Please retain this
manual for future reference or parts information.
Thank you for purchasing the GDIB-46L.
This gym is part of the Body-Solid line of quality
strength training machines, which let you target spe-
cic muscle groups to achieve better muscle tone
and overall body conditioning.
Unpacking the Equipment
The GDIB-46L is carefully tested and inspected before
shipment. We have shipped the unit in several pieces
that require assembly. Ask for assistance during the
assembly process. Carefully unpack the boxes and lay
the pieces on the oor near the area where you plan
to use the equipment.
The GDIB-46L is designed for your enjoyment. By fol-
lowing these precautions and using common sense,
you will have many safe and pleasurable hours of
healthful exercise with your Body-Solid GDIB-46L.
After assembly, you should check all functions to en-
sure correct operation. If you experience problems,
or if any items are missing, rst recheck the assembly
instructions to locate any possible errors made dur-
ing assembly. If you are unable to correct the prob-
lem, call the dealer from whom you purchased the
machine or call 1-800-556-3113 for the dealer near-
est you.
Obtaining Service
Please use this Owner’s Manual to make sure that all
parts have been included in your shipment. When
ordering parts, you must use the part number and
description from this Owner’s Manual. Use only Body-
Solid replacement parts when servicing this unit. Fail-
ure to do so will void your warranty and could result in
personal injury.
For information about product operation or service,
check out the ocial Body-Solid website at www.
bodysolid.com or contact an authorized Body-Solid
dealer or a Body-Solid factory-authorized service
company or contact Body-Solid customer service, M-F
8:30am-5:00pm CST, at one of the following:
* Toll Free: [phone]
 Local: [phone]
 Fax: [phone]
: E-mail: [email protected]
or write to:
+ Body-Solid, Inc.
Service Department
1900 S. Des Plaines Ave.
Forest Park, IL 60130 USA
Body-Solid continually seeks ways to improve the performance, specications and product manuals in order to ensure that only superior products are re-
leased from our factories. Please take the time to carefully read through this manual thoroughly. Instructions contained in this document are not intended
to cover all details or variations possible with Body-Solid equipment, or to cover every contingency that may be met in conjunction with installation,
operation, maintenance or troubleshooting of the equipment. Even though we have prepared this manual with extreme care, neither the publisher nor the
author can accept responsibility for any errors in, or omission from, the information given. Should additional information be required, or should situations
arise that are not covered by this manual, the matter should be directed to your local Body-Solid representative, or the Service Department at Body-Solid
Inc. in Forest Park, Illinois.
Any Questions?
Call [phone]

Preparations
6
CAUTION: To set up this unit, you will need assistance.
Do not attempt assembly by yourself.
You must review and follow the instructions in this Owner’s Manual. If you do not assemble and use the
GDIB-46L according to these guidelines, you could void the Body-Solid warranty.
Required Tools
The basic tools that you must obtain before assem-
bling the GDIB-46L include but are not limited to:
mStandard Wrench Set
mMetric Wrench Set
mAdjustable Wrench
mAllen Set
mRubber Mallet
mSilicone Spray Oil
mKnife
Installation Requirements
Follow these installation requirements when assem-
bling the GDIB-46L:
Set up the GDIB-46L on a solid, at surface.
A smooth, at surface under the machine helps keep
it level. A level machine has fewer malfunctions.
Provide ample space around the machine.
Open space around the machine allows for easier ac-
cess and a more comfortable workout.
Insert all bolts in the same direction.
For aesthetic purposes, insert all bolts in the same di-
rection unless specied (in text or illustrations) to do
otherwise.
Leave room for adjustments.
Tighten fasteners such as bolts, nuts, and screws so
the unit is stable, but leave room for adjustments. Do
not fully tighten fasteners until instructed in the as-
sembly steps to do so.
Fill out and mail the warranty card.
To benet from the best and most comprehensible
warranty in the tness industry, completely ll out
and mail the warranty card enclosed with the unit.
CAUTION !
Obtain assistance! Do not attempt to assemble
the GDIB-46L by yourself. Review the Installa-
tion Requirements before proceeding with the
following steps.

7
Assembly Instructions
Assembly of the GDIB-46L takes professional installers
about 1 hour to complete.
Professional installers are highly recommended!
If this is the rst time you have assembled this type of equipment, plan on signicantly more time. How-
ever, if you acquire the appropriate tools, obtain assistance, and follow the assembly steps sequentially,
the process will take time, but is fairly easy.
Assembly Tips
Read all “Notes”on each page before beginning each
step.
While you may be able to assemble the GDIB-46L us-
ing the illustrations only, important safety notes and
other tips are included in the text.
Some pieces may have extra holes that you will not
use. Use only those holes indicated in the instruc-
tions and illustrations.
IMPORTANT!
Before you begin you should look at the quick refer-
ence guide that shows all hardware parts (in actual
size) along with the corresponding component num-
bers in the assembly instructions.
To nd out the length of a particular bolt, measure its
shank (the long, narrow part beneath the head) using
the ruler below. Refer to the following diagram:

8
STEP
1
Be careful to assemble all components
in the sequence they are presented.
NOTE: Finger tighten all hardware in this step.
Do Not wrench tighten until the end of Step 3.
A. Insert both Foot Caps (14) into each Bottom Support Frame (H).
B. Connect both Bottom Support Frame (H) to Back Cross Frame (A) using for
each Bottom Support Frame (H):
Two 1 (M12x75 hex head bolt)
Two 7 (M12 washer)
Two 5 (M12 nylon lock nut)
C. Insert both Nylon Bushings (15) into Seat Carriage (C).
D. Insert Seat Carriage (C) onto Middle Frame (B) by loosening Pop Pin (28) and Knob (29).
E. Connect Middle Frame (B) to Back Cross Frame (A) using:
Two 1 (M12x75 hex head bolt)
Four 7 (M12 washer)
Three 5 (M12 nylon lock nut)
One 4 (M12x70 hex head bolt)
F. Insert End Cap (11) into Seat Carriage (C).

9
STEP
1
Above shows Step 1 assembled and completed.
S T E P
Above shows STEP 1
assembled and completed
1
1
H
77
4
7
11
7
A
1
1
5
7
5
7
14
14
H
7
5
7
14
15
15
11
C
5
5
B
5
14
28
5
29
S T E P
Above shows STEP 1
assembled and completed
1
1
H
77
4
7
11
7
A
1
1
5
7
5
7
14
14
H
7
5
7
14
15
15
11
C
5
5
B
5
14
28
5
29

10
STEP
2
Be careful to assemble all components
in the sequence they are presented.
NOTE: Finger tighten all hardware in this step.
Do Not wrench tighten until the end of Step 3.
A. Insert both End Caps (19) into Stabilizing Bar (G).
B. Lay Stabilizing Bar (G) on Back Cross Frame (A) as shown.
C. Insert a Nylon Bushing (16) onto each Back Cross Frame (A).
D. Insert an End Cap (12) into each Back Pad Frame (E).
E. Insert an End Cap (12) into each Seat Pad Frame (F).
F. Attach a Rubber Bar Catch (3) onto each Lift Off (D).
G. Insert a Lift Off (D) into each Back Cross Frame (A) by loosening Pop Pin (28).
H. Insert Seat Pad Frame (F) onto the shaft on each side of Seat Carriage (C).
I. Insert Back Pad Frame (E) onto the shaft on each side of Seat Carriage (C).
J. Connect Seat Pad (L) to Seat Pad Frame (F) using:
Four 2 (M8x45 hex head bolt)
Four 9 (M8 spring washer)
Four 8 (M8 washer)
NOTE: *Do NOT over-tighten the bolts as this will cause the T - nuts in pads to strip out.
Tighten the bolts until the spring lock washer is flat.
K. Connect Back Pad (K) to Back Pad Frame (E) using:
Six 2 (M8x45 hex head bolt)
Six 9 (M8 spring washer)
Six 8 (M8 washer)
NOTE: *Do NOT over-tighten the bolts as this will cause the T - nuts in pads to strip out.
Tighten the bolts until the spring lock washer is flat.
L. Insert Ball Pin (17) into Seat Pad Frame (F).

11
STEP
2
Above shows Step 2 assembled and completed.
S T E P
Above shows STEP 2
assembled and completed
K
L
12
89
2
8
9
2
8
9
2
12
892
89
2
89
2
12 8
9
2
8
9
2
12 8
9
2
8
9
217
E
E
A
19
28
28
19
16
16
D
D
13
13
G
C
F
F
S T E P
Above shows STEP 2
assembled and completed
K
L
12
89
2
8
9
2
8
9
2
12
892
89
2
89
2
12 8
9
2
8
9
2
12 8
9
2
8
9
217
E
E
A
19
28
28
19
16
16
D
D
13
13
G
C
F
F

12
STEP
3
Be careful to assemble all components
in the sequence they are presented.
NOTE: Finger tighten all hardware in this step.
Do Not wrench tighten until the end of Step 3.
A. Insert End Cap (21) into Leg Pivot Frame (I).
B. Insert three End Caps (19) into Leg Frame (J).
C. Insert Leg Pivot Frame (I) into Middle Frame (B) and secure using Ring Pin (18) Knob (29).
D. Insert Long Roller Bar (N) into Leg Pivot Frame (I).
E. Slide both Foam Rollers (24) onto each side of Long Roller Bar (N).
F. Slide both Nylon Washers (27) onto each side of Long Roller Bar (N).
G. Tap both Round End Caps (26) onto each end of Long Roller Bar (N).
H. Insert Rubber Cane Tip (23) onto Leg Frame (J).
I. Insert Round End Cap (22) onto Leg Frame (J).
J. Slide Leg Frame (J) into Leg Pivot Frame (I) using:
One 3 (1/2” x 85 hex head bolt)
Two 10 (round cap washer)
One 6 (1/2” nylon lock nut)
Two 20 (bolt cap)
K. Insert Ring Pin (25) into Leg Pivot Frame (I).
L. Insert both Short Roller Bars (M) into Leg Frame (J).
M. Insert both Foam Rollers (24) onto each Leg Frame (J).
N. Insert both Nylon Washers (27) onto each Leg Frame (J).
O. Tap both Round End Caps (26) onto each Leg Frame (J).
P. Congratulations! The assembly of the GDIB-46L is complete.

13
STEP
3
Above shows Step 3 assembled and completed.
S T E P
Above shows STEP 3
assembled and completed
26 27
24
N
20
3
10 21
10
620
24
27
26
I
26 27
24
M
26
27
24
22 19
M
24
27
26
23
26
19
B
J
19 25
24
27
18
29
S T E P
Above shows STEP 3
assembled and completed
26 27
24
N
20
3
10 21
10
620
24
27
26
I
26 27
24
M
26
27
24
22 19
M
24
27
26
23
26
19
B
J
19 25
24
27
18
29

Warning, Safety & Maintenance
14
Warning, Safety & Maintenance
Be sure that all users carefully read and understand all
warning, safety and maintenance labels on the machine
before each use. Failure to do so may result in serious injury.
It is imperative that you retain this Owner’s Manual and be
sure all warning labels are legible and intact. Replacement
Owner’s Manuals and labels are available from your local
Body-Solid dealer. If you have any questions about the
operation, set up or maintenance of this machine please call
our customer service department at 1 [phone].
#DWRULE-4
Warning Label for Rules
#DWSM-5
Warning Label for Maintenance
Warning, Safety & Maintenance
Be sure that all users carefully read and understand all
warning, safety and maintenance labels on the machine
before each use. Failure to do so may result in serious injury.
It is imperative that you retain this Owner’s Manual and be
sure all warning labels are legible and intact. Replacement
Owner’s Manuals and labels are available from your local
Body-Solid dealer. If you have any questions about the
operation, set up or maintenance of this machine please call
our customer service department at 1 [phone].
#DWRULE-4
Warning Label for Rules
#DWSM-5
Warning Label for Maintenance
It is imperative that the user becomes familiar and
understands all warnings posted on the unit.
To minimize the risk of injury, follow all safety guidelines provided with the unit and owner’s manual.
Be sure that all users carefully read and under-
stand all warning, safety and maintenance la-
bels on the machine before each use. Failure to
do so may result in death or serious injury.
It is imperative that you retain this Owner’s
Manual and be sure all warning labels are leg-
ible and intact. Replacement Owner’s Manuals
and warning labels are available from your local
Body-Solid dealer.
If you have any questions about the operation,
set up or maintenance of this machine please
call our customer service department at (800)
556-3113.

15
Warning, Safety & Maintenance
Serious injuries can be avoided with a thorough, careful
and daily inspection of your equipment.
Discontinue use and replace any worn parts immediately to avoid exposure to dangerous conditions.
Addendum
!
WARNING
To avoid serious injury, Weight Horn Collars must be
used to lock the weight plates onto the weight posts.
Failure to use Weight Horn Collars properly may result
in death or serious injury.
For more information or to purchase a Weight Horn Collar visit
www.bodysolid.com

Warning, Safety & Maintenance
16
Precision craftsmanship assures Body-Solid’s ability
to consistently deliver products of the highest stan-
dards. Our products have been carefully designed to
ensure safe, ecient long term operation.
However, it must be realized that safe use of this
equipment requires that owners carefully read and
follow the Body-Solid use recommendations, warn-
ings, and maintenance guidelines in this Owners
Manual.
Routine inspection and maintenance is of critical
importance to ensure maximum safety and perfor-
mance. Body-Solid uses the highest quality materials
available, but wear is inevitable. Therefore, you must
carefully inspect your equipment as outlined in the
Maintenance Schedule.
Be advised that dangerous conditions can arise even
during a warranty period. A warranty does not ne-
gate the owner’s responsibility to thoroughly, care-
fully and daily inspect the machine.
Including maintaining the equipment, the owner’s
responsibility is also to:
Be sure to always provide adequate supervision to all
end-users.
Be sure to instruct all end-users of proper usage.
Be sure all supervisors and personal trainers who
instruct end-users on equipment use are properly
trained and know the function and importance of
every adjustment and setting.
Also, be sure these trainers provide proper instruc-
tion to end-users on the fundamentals of strength
training.
CABLES:
While the machine is not in use, carefully run your
ngers along the cable to feel for thinning or bulg-
ing areas. Replace cables immediately at the rst
sign of damage or wear. Do not use the equipment
until the damaged cable has been replaced.
Visually inspect the cables for fraying, cracking,
peeling or discoloration.
Check slack in cables and re-adjust cable tension if
needed.
Check that the jam nut on the selector rod top bolt
is tight.
UPHOLSTERY:
Wipe down and sanitize after every workout.
Periodically take the time to use a mild soap or a
mild vinyl upholstery cleaner. Avoid using any abra-
sive cleaner not intended for use on vinyl.
Keep sharp or pointed objects out of your pockets
and clear of all upholstery.
NUTS/BOLTS/FASTENERS:
Periodically inspect all nuts and bolts. Tighten if
needed. If bolts seem to loosen periodically, use
Loctite 242 for a long-term cure.
Go through a re-tightening sequence periodically to
ensure that all hardware is properly tensioned.
GUIDE RODS:
Wipe clean with a dust free rag. Lubricate with a
Silicon or Teon based lubricant.
ADJUSTMENTS / LOCKING PINS /
TIGHTENING KNOBS:
Check all pieces for signs of visible wear or damage.
Check springs in Snap Links and Pop Pins for proper
tension and alignment.
If the spring sticks or has lost its rigidity, replace it
immediately.
ANTI-SKID SURFACES:
Replace if they appear worn or become slippery.
WARNING INSTRUCTION LABELS:
Inspect and familiarize yourself with all safety
warnings and other user information on decals.
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
m
It is imperative that the user becomes familiar and
understands all warnings posted on the unit.
To minimize the risk of injury, follow all safety guidelines provided with the unit and owner’s manual.

17
Warning, Safety & Maintenance
MAINTENANCE
SCHEDULE DAILY WEEKLY LATEST DATE ENTRY
CABLES:
CHECK TENSION, END FITTINGS AND COATING.
CHECK THAT JAM NUT ON THE SELECTOR ROD TOP
BOLT IS TIGHT
1.
2. üü
UPHOLSTERY:
WIPE DOWN AND DRY.
CLEAN AND CONDITION.
1.
2. üü
FRAME:
WIPE DOWN AND DRY.
POLISH AND WAX.
1.
2. üü
CHROME:
WIPE DOWN AND DRY.
POLISH AND LUBRICATE.
1.
2. üü
NUTS/BOLTS/FASTENERS:
TIGHTEN AND/OR ADJUST AS NEEDED.1. ü
GUIDE RODS:
LUBRICATE AND CLEAN.1. ü
LINEAR RODS:
LUBRICATE AND CLEAN.1. ü
SEAT SLEEVES:
LUBRICATE AND CLEAN.1. ü
ADJUSTMENTS/LOCKING PINS/
TIGHTENING KNOBS:
ADJUST ANDTIGHTEN AS NEEDED.1. ü
WEIGHT STACK PINS:
CHECK INTEGRITY OF PIN.1. ü
WARNING LABELS:
CHECK INTEGRITY.
IF TORN, DISCONTINUE OPERATION AND REPLACE
WARNING LABEL.
1.
2. ü
SPRINGS AND POP PINS:
ADJUST ANDTIGHTEN AS NEEDED.
REPLACE WORN SPRINGS.
1.
2. ü
ANTI-SKID SURFACES:
CHECK INTEGRITY.
REPLACE IF PEELING OR DAMAGED.
1.
2. ü
HAND GRIPS/ROLLERS:
CHECK INTEGRITY.
REPLACE IFWORN OR DAMAGED.
1.
2. ü
FOR BODY-SOLID CUSTOMER SERVICE:
1-800-556-3113
Make several copies of this page to keep track of your maintenance.
You can print more copies of this page by going to:
http://www.bodysolid.com/support/docs.html
)

18
Mainframe Parts List
Part numbers are required when ordering parts.
Part# Qty Description
A 1 BACK CROSS FRAME
B 1 MIDDLE FRAME
C 1 SEAT CARRIAGE
D 2 LIFT OFF
E 2 BACK PAD FRAME
F 2 SEAT PAD FRAME
G 1 STABILIZING BAR 38 x 1.8T x 1048L
H 2 BOTTOM SUPPORT FRAME 50 x 1.8T x 450L
I 1 LEG PIVOT FRAME
J 1 LEFT FRAME
K 1 BACK PAD
L 1 SEAT PAD
M 2 SHORT ROLLER BAR f 1” x 1.6T x 473L
N 1 LONG ROLLER BAR f 1” x 1.6T x 493L

Part numbers are required when ordering parts.
45 19
H a r d w a r e L i s t
Part# Qty Description
1 6 HEX HEAD BOLT M12x75
2 10 HEX HEAD BOLT M8x45
3 1 HEX HEAD BOLT ½” x 85
4 1 HEX HEAD BOLT M12x70
5 7 NYLON LOCK NUT M12
6 1 NYLON LOCK NUT ½”
7 8 WASHER M12x34
8 10 WASHER M8x18
9 10 SPRING WASHER M8
10 2 ROUND CAP WASHER M12
11 1 END CAP 30x30 (9211-002)
12 4 END CAP 1” x 1” (9211-001)
13 2 RUBBER BAR CATCH 38x38 (9310-001)
14 4 FOOT CAP 2” x 2” (9211-024)
15 2 NYLON BUSHING 60x45 (9211-032)
16 2 NYLON BUSHING 50x45 (9211-030)
17 1 BALL PIN f 10x120L (8250-017)
18 1 RING PIN f 10x65L (8250-015)
19 5 END CAP 1 ½” x 1 ½” (9211-003)
20 2 BOLT CAP M12
21 1 END CAP 45x45 (9211-004)
22 1 ROUND END CAP f 1” (9211-016)
23 1 RUBBER CANE TIP f 1” (9212-019)
24 6 FOAM ROLLER f 3 ½” x 8” (9161-055)
25 1 RING PIN f 10x75L (8250-034)
26 6 ROUND END CAP f 1” (9211-022)
27 6 NYLON WASHER f 3” (9214-008)
28 3 POP PIN (8250-012)
29 2 KNOB (9215-004)
30 2 COPPER BUSHING f 21 OD x 12.85 ID x 10L (8520-001)
31 1 BODYSOLID LOGO (9440-027)
32 3 POP PIN STICKER (9440-104)
33 1 BODYSOLID PLASTIC PLATE (9440-199)
34 1 WARNING STICKER (9440-217)
35 1 WARNING STICKER (9440-105)
36 1 MAINTENANCE LABEL (9440-103)
Part numbers are required when ordering parts.

45 20
H a r d w a r e (To Scale)
Part# 1 M12x75 Hex Head Bolt Qty. 6
Part# 2 M8x45 Hex Head Bolt Qty. 10
Part# 3 ½” x 85 Hex Head Bolt Qty. 1
Part# 4 M12x70 Hex Head Bolt Qty. 1
Part# 5 M12 Nylon Lock Nut Qty. 7
G D I B - 4 6 L H A R D W A R E
( s h o w n i n a c t u a l s i z e )
KEY #1 HEX BOLT M12 X 75 PARTIAL THREAD QTY.6
KEY #2 HEX BOLT M8 X 45 FULL THREAD QTY.10
KEY #3 HEX BOLT 1/2" X 85 PARTIAL THREAD QTY.1
KEY #4 HEX BOLT M12 X 70 PARTIAL THREAD QTY.1
KEY #5 NYLON LOCK NUT M12 QTY.7
KEY #6 NYLON LOCK NUT 1/2" QTY.1
G D I B - 4 6 L H A R D W A R E
( s h o w n i n a c t u a l s i z e )
KEY #1 HEX BOLT M12 X 75 PARTIAL THREAD QTY.6
KEY #2 HEX BOLT M8 X 45 FULL THREAD QTY.10
KEY #3 HEX BOLT 1/2" X 85 PARTIAL THREAD QTY.1
KEY #4 HEX BOLT M12 X 70 PARTIAL THREAD QTY.1
KEY #5 NYLON LOCK NUT M12 QTY.7
KEY #6 NYLON LOCK NUT 1/2" QTY.1
G D I B - 4 6 L H A R D W A R E
( s h o w n i n a c t u a l s i z e )
KEY #1 HEX BOLT M12 X 75 PARTIAL THREAD QTY.6
KEY #2 HEX BOLT M8 X 45 FULL THREAD QTY.10
KEY #3 HEX BOLT 1/2" X 85 PARTIAL THREAD QTY.1
KEY #4 HEX BOLT M12 X 70 PARTIAL THREAD QTY.1
KEY #5 NYLON LOCK NUT M12 QTY.7
KEY #6 NYLON LOCK NUT 1/2" QTY.1
G D I B - 4 6 L H A R D W A R E
( s h o w n i n a c t u a l s i z e )
KEY #1 HEX BOLT M12 X 75 PARTIAL THREAD QTY.6
KEY #2 HEX BOLT M8 X 45 FULL THREAD QTY.10
KEY #3 HEX BOLT 1/2" X 85 PARTIAL THREAD QTY.1
KEY #4 HEX BOLT M12 X 70 PARTIAL THREAD QTY.1
KEY #5 NYLON LOCK NUT M12 QTY.7
KEY #6 NYLON LOCK NUT 1/2" QTY.1
G D I B - 4 6 L H A R D W A R E
( s h o w n i n a c t u a l s i z e )
KEY #1 HEX BOLT M12 X 75 PARTIAL THREAD QTY.6
KEY #2 HEX BOLT M8 X 45 FULL THREAD QTY.10
KEY #3 HEX BOLT 1/2" X 85 PARTIAL THREAD QTY.1
KEY #4 HEX BOLT M12 X 70 PARTIAL THREAD QTY.1
KEY #5 NYLON LOCK NUT M12 QTY.7
KEY #6 NYLON LOCK NUT 1/2" QTY.1
G D I B - 4 6 L H A R D W A R E
( s h o w n i n a c t u a l s i z e )
KEY #1 HEX BOLT M12 X 75 PARTIAL THREAD QTY.6
KEY #2 HEX BOLT M8 X 45 FULL THREAD QTY.10
KEY #3 HEX BOLT 1/2" X 85 PARTIAL THREAD QTY.1
KEY #4 HEX BOLT M12 X 70 PARTIAL THREAD QTY.1
KEY #5 NYLON LOCK NUT M12 QTY.7
KEY #6 NYLON LOCK NUT 1/2" QTY.1