Borg & Overstrom T1 Tap systems User manual

Borg & OverströmGB01
Dispense Options
Contents
NOTE: This booklet to be left with
appliance following installation
Component/Feature Overview
Operation
Functions & Controls
General Safety
CO2 Bottle Installation
Fault Finding
User Guide
Chilled Ambient Sparkling
T1 Tap systems

Component/
Feature Overview
Contents:
1 no T1 Tap with Control Panel
1 no 1.0m x 6mm Insulated Water Pipe
1 no Connector Cable
1 no Fixings Set
Please Note:
Drip trays, Mains Installation Kits &
Filters are supplied as extra items
according to individual ordering
requirement.
Main Body
Faucet
Control Panel
T1 Tap -
Major Components
Mounting Threads &
Fixing Plate
Connector Cable

Water Inlet
Top Panel
Unit Carry Handle
Side Panel
Water Outlet
Power Connection
On/Off Switch
Tap Connection
*Sparkling versions only
Contents:
1 no ProCore Unit
1 no 2.0m Power Cord Set
1 no Co2 Regulator with Gauge & Connection tube*
1 no ProCore Simple-t Ventilation Kit
ProCore™ Undercounter -
Major Components
CO2 Inlet*

Front Panel
ProCore Simple-t
Base
ProCore Simple-t
Chimney

Operation & Connections
Basic Functions
Tap Control Panel
Dispensing from unit:
Press and hold dispense icon and release to nish dispense.
Chilled Dispense
Ambient Dispense
Sparkling Dispense
Outlet Pipe
CO2 Pipe
CO2 Bottle
Tap connection
cable
Inlet Pipe
Connections Overview

Basic Troubleshooting
Problem/Report Possible Cause Suggested Action
No Water Dispensing Water Pressure Regulator Contact your distributor
No Sparkling Water -
If applicable
No CO2 pressure Check CO2 bottle, regulator and non- return
valve. Supply pressure should be 58 psi (3.5-
4bar), replace as necessary
Carbonator Tank Not Filling Contact your distributor
Poor Quality Carbonation -
If applicable
Air in Carbonator Tank Isolate the power supply and operate the spar-
kling water tap until gas is expelled. Allow gas
to expel for 5 seconds. Switch on power supply
and allow the tank to rell
Residue in Carbonator Tank After prolonged use, a surface lm can develop
within the carbonator tank. Refer to cleaning
and sanitising instructions
Carbonator Tank is Overlled If pump runs continuously, contact your
distributor
Warm Drinks Insufcient cooling air ow through the fridge Check that the ventilation kit has been installed
correctly.
Compressor not running Contact your distributor
PCB not operating
Fridge failure
General Safety
General Safety
- Always place the dispenser in its vertical position,
on a surface which can capably support its weight.
- During use this machine must remain in
its upright position.
- Adequate ventilation must be allowed for - we
recommend using the supplied ventilation ducting kit.
- Keep the machine away from sunlight, heat and moisture.
- The environment where this machine is installed must be
free of dust and corrosive/explosive gases.

Unpack CO2 Regulator and t
elbow tting to spigot outlet.
Attach the regulator to the
disposable CO2 bottle, ensuring
the pressure relief vent is facing
away from you. Ensure the
regulator is closed.
Stand the cylinder in a suitable
place.
Allow the machine to stand for
8 - 12 minutes for the initial chilling
process to complete.
It is necessary to prime the sparkling system
- push the sparkling button for a few seconds
until CO2 is coming through. Check and
adjust the CO2 pressure accordingly.
Connect the assembled CO2
bottle and regulator to the CO2
inlet using a ¼” pipe.
We recommend between 3.5 - 4
bar (58 PSI) (max). Do not exceed
4 bar pressure.
58 PSI
10
mins
CO2 Bottle Installation - Sparkling Versions Only
123
4
7
56
OFF

© Copyright Borg & Overström.
This guide is printed by Borg & Overström and
shall not be reproduced or copied in anyway.
Ref: 702081
Version: V.26042022
Customer services:
[e-mail]
call [phone]
For full distributor
service manual visit:
www.borgandoverstrom.com/manual/t1