Bosch D9412GV3 User manual

D9412GV3/D7412GV3/D7212GV3
Control Panels Quick Reference Guide
en Quick Reference Guide

D9412GV3/D7412GV3/D7212GV3 Table of Contents | en 3
Bosch Security Systems, Inc. Quick Reference Guide F01U170805 | 01 | 2010.11
Table of Contents
1 GV3 Control Panel Connections (D9412GV3 Shown) 5
2 Upgrade GV3 Hardware and Programming 7
2.1 Receive Existing Control Panel Programming 7
2.1.1 Receive Existing Control Panel Programming with RPS 7
2.2 Upgrade Hardware to a GV3 Series Control Panel 7
2.2.1 Prepare to Remove Existing Hardware 7
2.2.2 Remove the Existing Control Panel 7
2.2.3 Install the GV3 Control Panel In the Enclosure 8
2.2.4 Replace the Terminal Strips 8
2.3 Upgrade Programming to a GV3 Control Panel Programming 9
2.3.1 Upgrade a GV2 Series, G Series, or Non-G Series Control Panel to a GV3 v8.03 or Later Using Remote
Programming Software (RPS) 5.13 or Later9
3 Programming the Control Panel 10
3.1 RPS Programming over a Network Using the DX4020 Ethernet Network Interface Module 10
3.2 RPS Programming over a Network Using the ITS-DX4020-G GPRS/GSM Communicator 10
3.3 RPS Programming Using the DX4010V2 RS-232/USB Serial Interface Module 10
3.4 RPS Programming Using the Keypad Programming 10
4 Programming to Set Up Central Station Reporting 11
4.1 Basic Telephone Set Up in RPS 11
4.2 Basic Internet Protocol (IP) 11
4.3 Account Number 11
5 Programming the Control Panel for Common Reporting Options 12
5.1 Set Up Daily Test Report Using RPS 12
5.2 Set Up Open and Close Reports Using RPS 12
5.2.1 Area Wide Parameters 12
5.2.2 Set Authority Level 12
6 Setting Up Points and Outputs 13
6.1 Using the Relay Option Within Point Assignments 13
6.2 Point Index (Default Values) 14
7 Add System Users Locally With a Keypad 16
7.1 Add Users (CMD 56) Using a Keypad 16
7.2 Add Card (CMD 56) for Access Control Only Using a Keypad 16
8 Turning the System ON or OFF and Keypad Commands 17
8.1 Arming and Disarming the System 17
8.1.1 Master Arming 17
8.1.2 Disarming 17
8.1.3 Set Duress +1 Using RPS 17

4en | Table of Contents D9412GV3/D7412GV3/D7212GV3
F01U170805 | 01 | 2010.11 Quick Reference Guide Bosch Security Systems, Inc.
8.2 Basic and Advanced Commands 17
8.3 SIA CP-01 False Alarm Prevention Options 18
9 Setting DIP Switches 19
9.1 D9127 U/T POPIT Dip Switch Key 19
9.2 D9210B Switch Settings 19
9.3 D720, D1255, D1260 Dip Switch Settings 19
9.4 D9131A Dip Switch Settings 19
9.5 D8129 OctoRelay Dip Switch Settings 19
9.6 D8128C OctoPOPIT Dip Switch Settings 19
9.7 D8128D OctoPOPIT Dip Switch Settings 19
10 Reporting Format Definitions 20
11 Frequently Asked Questions 24

D9412GV3/D7412GV3/D7212GV3 GV3 Control Panel Connections (D9412GV3 Shown) | en 5
Bosch Security Systems, Inc. Quick Reference Guide F01U170805 | 01 | 2010.11
1 GV3 Control Panel Connections (D9412GV3 Shown)

6en | GV3 Control Panel Connections (D9412GV3 Shown) D9412GV3/D7412GV3/D7212GV3
F01U170805 | 01 | 2010.11 Quick Reference Guide Bosch Security Systems, Inc.

D9412GV3/D7412GV3/D7212GV3 Upgrade GV3 Hardware and Programming | en 7
Bosch Security Systems, Inc. Quick Reference Guide F01U170805 | 01 | 2010.11
2 Upgrade GV3 Hardware and Programming
2.1 Receive Existing Control Panel Programming
2.1.1 Receive Existing Control Panel Programming with RPS
1. In RPS, double-click on the control panel name.
2. Click Connect. Once connected, the Panel Sync window opens.
3. Select the Recieve Panel Data option button and click OK.
2.2 Upgrade Hardware to a GV3 Series Control Panel
2.2.1 Prepare to Remove Existing Hardware
1. Power down the existing control panel by disconnecting the battery and the AC power.
2. Remove the four removable terminal strips by tilting the strip up and outward.
Do not remove the wiring from the terminal strip.
2.2.2 Remove the Existing Control Panel
1. Remove the lock down tab screw.
2. Lift up on the control panel to free it from the enclosure mounting hooks, and remove the
control panel from the enclosure it.
NOTICE!
GV3 Series v8.11 and later Control Panels are not compatible with the D5200 Programmer.
1 - Removable terminal strips
1 - Lock down tab

8en | Upgrade GV3 Hardware and Programming D9412GV3/D7412GV3/D7212GV3
F01U170805 | 01 | 2010.11 Quick Reference Guide Bosch Security Systems, Inc.
2.2.3 Install the GV3 Control Panel In the Enclosure
1. Place the GV3 Control Panel in the enclosure using the mounting skirt hook holes on the
back of the control panel and the mounting skirt hooks on the enclosure.
2. Replace the lock down tab screw.
2.2.4 Replace the Terminal Strips
1. Replace the four removable terminal strips by pushing them straight down until they snap
into position.
2. Connect the battery and AC power.
1 - Mounting skirt hook holes
2 - Mounting skirt hooks
3 - Lock down tab
NOTICE!
If the control panel was previously mounted using the screw hole configuration, the you must
re-mount the new control panel. The GV3 control panel mounting screw hole locations do not
align with the locations for older control panels.

D9412GV3/D7412GV3/D7212GV3 Upgrade GV3 Hardware and Programming | en 9
Bosch Security Systems, Inc. Quick Reference Guide F01U170805 | 01 | 2010.11
2.3 Upgrade Programming to a GV3 Control Panel Programming
2.3.1 Upgrade a GV2 Series, G Series, or Non-G Series Control Panel to a GV3
v8.03 or Later Using Remote Programming Software (RPS) 5.13 or Later
1. In RPS, highlight the control panel name by selecting it.
2. Click the View button on the Remote Programmer Toolbar.
3. In the resulting Panel Data - View window, click the Edit button.
4. In the resulting Panel Data - Edit window, select the new control panel type from the
Panel Type drop-down. (If the control panel is a G or Non-G Series control panel, you
must upgrade to GV2 first, and then repeat each of these steps to choose the GV3
control panel.) Click OK to close the window.
5. Click Save in the Panel View window to save the changes and close the Panel View
window.
6. Click Connect. Once connected, the Panel Sync window opens.
7. Select the Send ALL RPS Data to Panel option button and click OK.
8. Once the sync completes, click Disconnect to disconnect from the control panel.
9. Exit RPS.
10. Test the control panel for operation.
NOTICE!
You must upgrade G Series and Non-G Series control panels to GV2 programming prior to
upgrading to GV3 programming.

10 en | Programming the Control Panel D9412GV3/D7412GV3/D7212GV3
F01U170805 | 01 | 2010.11 Quick Reference Guide Bosch Security Systems, Inc.
3 Programming the Control Panel
You can program the control panel with RPS using a network connection or serial connection.
You can program some paramaters of the control panel with keypad programming.
3.1 RPS Programming over a Network Using the DX4020 Ethernet
Network Interface Module
For additional information, refer to IP Address Programming in the Conettix DX4020 Network
Interface Module Installation Guide (P/N: F01U045288).
3.2 RPS Programming over a Network Using the ITS-DX4020-G
GPRS/GSM Communicator
For additional information, refer to the Conettix ITS-DX4020-G Installation Guide
(P/N: F01U163066).
3.3 RPS Programming Using the DX4010V2 RS-232/USB Serial
Interface Module
For additional information, refer to the DX4020 RS-232/USB Serial Interface Module Installation
Instructions (P/N: F01U083036).
3.4 RPS Programming Using the Keypad Programming
For additional information, refer to the D9412GV3/D7412GV3 Program Entry Guide
(P/N: F01U170807) or the D7212GV3 Program Entry Guide (P/N: F01U170808).

D9412GV3/D7412GV3/D7212GV3 Programming to Set Up Central Station Reporting | en 11
Bosch Security Systems, Inc. Quick Reference Guide F01U170805 | 01 | 2010.11
4 Programming to Set Up Central Station Reporting
4.1 Basic Telephone Set Up in RPS
1. Go to PANEL WIDE PARAMETERS→Phone and Phone Parameters.
2. Enter the primary telephone number in the Phone 1 field.
3. If a secondary telephone number is required, enter it in the Phone 2 field.
4. Go to Panel Wide Parameters→Routing→Route Group 1.
5. Enter Phone 1 in the Primary field.
6. If a secondary telephone is required, enter Phone 2 in the Backup field.
4.2 Basic Internet Protocol (IP)
1. Go to PANEL WIDE PARAMETERS→Routing→Route Group 1 Primary.
2. Enter SDI 88 Path 1 (or SDI 92 Path 1).
3. Go to AUXPARM→Enhanced Communications.
4. Select or enter the following values:
4.3 Account Number
In RPS, go to AREA WIDE PARAMETERS and enter the account number (up to 10 digits) in
the Account Number parameter.
NOTICE!
You can program these items using RPS and the steps listed below. You can also use keypad
programming with v8.11 and later (refer to the D9412GV3/D7412GV3 Program Entry Guide
(P/N: F01U170807) or the D7212GV3 Program Entry Guide (P/N: F01U170808).
NOTICE!
Enhanced Communications settings usually follow the recommendations of the Central
Stations’ staff.
If using an ITS-DX4020-G for communication, refer to the ITS-DX4020-G Installation and
Operation Guide (P/N: F01U163066).
Parameter Value
Enable Enhanced Communication YES
Path 1 IP Address IP address of Central Station receiver
Path 1 Port Number Port Number of Central Station receiver
Path 1 Poll Rate (seconds)1Poll rate recommended by Central Station
Path 1 ACK Wait Time 13 sec (default setting)
Path 1 Retry Count 5 (default Setting)
1If the control panel is programmed to send a heartbeat poll to the central station, a rate of 75 sec
maintains the virtual link in most network configurations.
NOTICE!
Area 1 is the only area turned on by default.

12 en | Programming the Control Panel for Common Reporting Options D9412GV3/D7412GV3/D7212GV3
F01U170805 | 01 | 2010.11 Quick Reference Guide Bosch Security Systems, Inc.
5 Programming the Control Panel for Common
Reporting Options
5.1 Set Up Daily Test Report Using RPS
1. Go to SCHEDULES→Skeds.
2. Enter Function Code 9 (Test Report) in an unused Sked.
3. Select NO for the Deferred parameter to send test reports regardless of other test
reports sending between scheduled test reports.
4. Select NO for the Hourly parameter to send test reports only when the sked executes and
not every hour.
5. Enter the time at which you wish the schedule to send the report.
6. Leave the Date parameter disabled so that the sked executes by days of the week instead
of only on a selected date.
7. Select YES for each day of the week.
8. Select NO for:
– Except On Holiday
–Holidays1-4
5.2 Set Up Open and Close Reports Using RPS
5.2.1 Area Wide Parameters
To report each area independently:
–GotoAREA WIDE PARAMETERS→Area/Bell,Open/Close Options→Acct Open/Close in
RPS. Select NO (default).
–GotoArea Open/Close in RPS). Select YES (default).
To report by account (Close signal is sent when the last area in an account is armed; Open
signal is sent when the first area is disarmed):
– GotoAREA WIDE PARAMETERS→Area/Bell,Open/Close Options→Acct Open/Close
in RPS. Select YES.
– GotoArea Open/Close in RPS. Select NO.
5.2.2 Set Authority Level
1. Go to USER INTERFACE→Authority Levels.
2. Go to the Authority Level to be used by users sending Open and Close reports.
3. Select E(enabled) for Area Open/Close.
4. Select Efor Restricted Open/Close.
5. Select Efor Perimeter Open/Close.
NOTICE!
If you want Perimeter Open and Close, select Perimeter O/C = YES.

D9412GV3/D7412GV3/D7212GV3 Setting Up Points and Outputs | en 13
Bosch Security Systems, Inc. Quick Reference Guide F01U170805 | 01 | 2010.11
6 Setting Up Points and Outputs
6.1 Using the Relay Option Within Point Assignments
Relay Programming allows any one point or several points to latch a single relay through
software when the selected point generates an alarm. Relays are number 1 through 8 and are
programmed by entering the number of the relay (1 - 8) in the Relay column in Point
Assignments. This relay latches on a generated alarm and resets after acknowledging and then
clearing the alarm from memory.
Table 6.1 Actual Relays Latched by Control Panel Type
Table 6.2 D8129 Switch Settings for All Control Panel Types
Relay
D8129 Actual Relay Number
D7412GV3/D7212GV31D9412GV32
19 73
210 74
311 75
412 76
513 77
614 78
715 79
816 80
1For the D7412GV3 and D7212GV3, connect to Terminal 28 for data (Zonex 1 Out).
2For the D9412GV3, connect to Terminal 26 for data (Zonex 2 Out).
Switch Number Setting
1ON
2OFF
3ON
4ON
NOTICE!
Programmers must be aware of the following considerations:
– Do not use relays designated within Point Assignments for multiple functions. For
example, Relays 73 through 80 on the D9412GV3 should not be used for relay-follow-
point or area-wide or panel-wide relays.
– Relays should not be selected to follow points programmed as Invisible Points.

14 en | Setting Up Points and Outputs D9412GV3/D7412GV3/D7212GV3
F01U170805 | 01 | 2010.11 Quick Reference Guide Bosch Security Systems, Inc.
6.2 Point Index (Default Values)
Table 6.3 Point Index Numbers and Descriptions
To make a custom Point Index, refer to (Table 6.4 and Table 6.5).
Table 6.4 Point Type Selections
Pt Index
Number
Description Pt Index
Number
Description
1 24-Hour Instant Audible Alarm on Open or
Short
17 D279 (Non-Priority)
2 Invisible/Silent Hold Up on Short 18 D279 (Priority)
3 Fire Pull Station Alarm on Short 19 Easikey Input
4 Smoke Detector with Reset Alarm on Short 20 POPIT Motion Sensor Interior
5 Smoke Detector with Verification Reset and
Alarm on Short
21 POPIT Motion Sensor Perimeter
6 Bell Supervision Trouble on Open/Short 22 Fire Supervisory on Open, Trouble on Short
7 Perimeter Instant Alarm on Open or Short,
Watch Point when Disarmed
23 Non-Fire Supervisory on Open, Trouble on
Short
8 Perimeter Delay on Short, Instant Alarm on
Short, Watch Point when Disarmed
24 Local, No Visual or Audible Display on Any Fault
Armed or Disarmed with Relay Output
9 Perimeter Instant Alarm on Open or Short,
Local while Disarmed
25 Perimeter Delay on Open, Alarm on Short
10 Interior Instant Alarm on Open or Short 26 24-Hour Instant Audible Alarm on Open or
Short
11 Interior Delay on Short, Alarm on Open 27 24-Hour Instant Audible Alarm on Open or
Short
12 Interior Instant Alarm on Open or Short, Local
while Disarmed
28 24-Hour Instant Audible Alarm on Open or
Short
13 Interior Follower Delay on Short, Alarm on
Open
29 24-Hour Instant Audible Alarm on Open or
Short
14 Maintained Keyswitch 30 24-Hour Instant Audible Alarm on Open or
Short
15 Momentary Keyswitch 31 24-Hour Instant Audible Alarm on Open or
Short
16 Open/Close on Fault
NOTICE!
The default indexes are not always the best selection.
If you experience unwanted trouble conditions, refer to Table 6.5 on Page 15 and make any
necessary adjustments.
Bosch Commercial Wireless points produce a Short when faulted and an Open for a tamper.
Pt Type Description Pt Type Description
0 24-Hour 6 O/C/ Port
1 Perimeter 7 D279 (O/C Non-Priority)
2 Interior 8 D279 (Priority)
3 Interior Follower 9 Easikey
4 Keyswitch 11 AUX AC Supervision
5 Keyswitch Memory

D9412GV3/D7412GV3/D7212GV3 Setting Up Points and Outputs | en 15
Bosch Security Systems, Inc. Quick Reference Guide F01U170805 | 01 | 2010.11
To make a custom point index, use Table 6.4 on Page 14 and Table 6.5 on Page 15. For
example, to create an Interior Follower point with a delay on Open and Trouble on Short, use
Point Type 3 and Point Response 5.
Table 6.5 Point Response Selections
NOTICE!
The selections in Table 6.5 indicate:
– D = Delayed Response
– I = Instant Alarm
– S = Supervisory
– T = Trouble
– Blank = No Response
Point Response
Selections*
0123456789ABCDEF
Armed OpenIIIIDDIIDIIIIIT
ShortIIIIIIDDDI IIIII
Disarmed Open T T T I I T I T
Short T T T I T I I
24-HourOpenITIT ITSTS S N/A
ShortI I TTI T TS SS

16 en | Add System Users Locally With a Keypad D9412GV3/D7412GV3/D7212GV3
F01U170805 | 01 | 2010.11 Quick Reference Guide Bosch Security Systems, Inc.
7 Add System Users Locally With a Keypad
7.1 Add Users (CMD 56) Using a Keypad
Table 7.1 Adding Users with Command 56
7.2 Add Card (CMD 56) for Access Control Only Using a Keypad
Table 7.2 Adding Cards with Command 56
Step Operator Entry Keypad Response
1 Enter Command 56 Enter Passcode
2 Enter passcode and press [ENT]. Enter User #
3 Enter the user number and press [ENT]. USER # (default name text)
4 Enter Change Passcode?
5Enter EnterNewCode
6 Enter the new user’s passcode. Enter New Again
7 Re-enter the new passcode. Code Changed
Step Operator Entry Keypad Response
1 Command 56 Enter Passcode
2 Enter passcode and press [ENT] Enter User #
3 Enter the user number and press [ENT] USER# (default name text)
4 Enter Change Passcode?
5Next AddCard?
6 Enter Present Card
7 Present the credential to the reader. Card Added
NOTICE!
To use Add Card (CMD 56), you must program the Assign Door prompt within Command
Center Assignments with the D9210B door controller number. If you do not program the
Assign Door prompt, the keypad reads 9210 NOT READY.

D9412GV3/D7412GV3/D7212GV3 Turning the System ON or OFF and Keypad Commands | en 17
Bosch Security Systems, Inc. Quick Reference Guide F01U170805 | 01 | 2010.11
8 Turning the System ON or OFF and Keypad Commands
8.1 Arming and Disarming the System
8.1.1 Master Arming
Enter the passcode and [ENTER] to arm all areas where the user has authority and are areas
within the scope of the keypad.
8.1.2 Disarming
Enter the passcode and [ENTER] to disarm all areas where the user has authority and are
areas within the scope of the keypad.
8.1.3 Set Duress +1 Using RPS
1. Go to PANEL WIDE PARAMETERS→Miscellaneous→Duress Type. Select 1.
2. Go to AREA WIDE PARAMETERS→Area Parameters→Duress Enable. Select YES.
3. Go to User Interface→Authority Levels. In the authority levels to be used, select Efor
the Send Duress parameter.
8.2 Basic and Advanced Commands
Table 8.1 Basic and Advanced Commands
99 Enter Commands
For each of the following commands, press [9] [9] [ENTER]. Press [NEXT] to view each
command.
– 1 - View Log
– 2 - Print Log
– 3 - Display Revision
– 4 - Service Walk
– 5 - Default Text
– 6 - Keypad Programming (Requires Service Passcode)
Basic Commands Advanced Commands
CMD 1 (Master Arm) [Master Arms only the
area assigned to the Keypad]
CMD 0 (Bypass a Point)
CMD 11 (Master Arm Instant) CMD 00 (Unbypass a Point)
CMD 3 (Perimeter Delay) CMD 41 (Test Report)
CMD 4 (Silence Trouble Sounder) CMD 42 (Status Report)
CMD 4, 0 (View memory) CMD 43 (Remote Program)
CMD 4, 4 (Walk Test) CMD 45 (Change Time/Date)
CMD 4, 7 (Reset Sensors) CMD 49 (Change Display)
CMD 6 (Watch Mode) CMD 50 (Move to Area)
CMD 7 (Special Alert) CMD 51 (Extend Closing)
CMD 8 (Perimeter Partial) CMD 52 (Change Sked)
CMD 9 (Special Alert) CMD 53 (Delete Passcode)
CMD 2 Perimeter Instant CMD 54 (Change Relay)
CMD 55 (Change Passcode)
CMD 56 (Add Passcode)
CMD 58 (Fire Test)
PRINT LOG (99 [ENTER])
VIEW LOG (99 [ENTER])

18 en | Turning the System ON or OFF and Keypad Commands D9412GV3/D7412GV3/D7212GV3
F01U170805 | 01 | 2010.11 Quick Reference Guide Bosch Security Systems, Inc.
8.3 SIA CP-01 False Alarm Prevention Options
–Master Arm-No Exit=YES: This setting provides for a Perimeter Delay point to be faulted
when master arming each area, or the arming state defaults to Perimeter Delayed.
–Exit Delay Warning=YES: When this parameter is set to YES, the alarm bell pulses on and
off every two seconds for the remaining 10 sec of Exit Delay.
–Entry Delay Warning=YES: When this parameter is set to YES, the alarm bell pulses on
and off every two seconds for the remaining 10 sec of Entry Delay.
NOTICE!
Some programming parameters are preset for compliance with SIA standard CP-01 (false
alarm prevention). These settings are in AREA WIDE PARAMETERS→Area Parameters. They
affect control panel operation as described below.

D9412GV3/D7412GV3/D7212GV3 Setting DIP Switches | en 19
Bosch Security Systems, Inc. Quick Reference Guide F01U170805 | 01 | 2010.11
9 Setting DIP Switches
9.1 D9127 U/T POPIT Dip Switch Key
POPIT addresses are binary. Refer to Table 9.1:
Table 9.1 POPIT Dip Switch Keys
To calculate the switch settings for POPITS, you must determine the value to use in the
calculation. For addresses 9 through 127, subtract 9. For addresses 129 through 247,
subtract 129. Use the following procedure with address 48 as the example, substituting the
actual values in your calculation.
1. Subtract 9 from 48. The result is 39.
2. Set the switches that add up to 39 to the OFF positions (32 + 4 + 2 + 1 = 39).
SW 1 OFF = 32
SW 4 OFF = 4
SW 5 OFF = 2
SW 6 OFF = 1
9.2 D9210B Switch Settings
For additional information, refer to the Access Control Interface Module D9210B Operation and
Installation Guide (P/N: 32206).
9.3 D720, D1255, D1260 Dip Switch Settings
For additional information, refer to:
–D720 Series Keypads Installation Instructions (P/N: 7406918000)
–D1255/D1255B Keypads Installation Instructions (P/N: 7406819000)
–D1260/D1260B Keypads Installation Guide (P/N: 48101)
9.4 D9131A Dip Switch Settings
For additional information, refer to the Parallel Printer Interface D9131A Installation Guide
(P/N: F01U135506).
9.5 D8129 OctoRelay Dip Switch Settings
For additional information, refer to the D8129 OctoRelay Module Operating and Installation
Guide (P/N: F01U036302).
9.6 D8128C OctoPOPIT Dip Switch Settings
For additional information, refer to the D8128C OctoPOPOIT Module Operating Instructions
(P/N: 7407710000).
9.7 D8128D OctoPOPIT Dip Switch Settings
For additional information, refer to the D8128D OctoPOPOIT Module Installation Guide
(P/N: F01U070537).
Switch Number 0123456
Binary Value 6432168421

20 en | Reporting Format Definitions D9412GV3/D7412GV3/D7212GV3
F01U170805 | 01 | 2010.11 Quick Reference Guide Bosch Security Systems, Inc.
10 Reporting Format Definitions
Modem IIIa2Event Modem IIIa2Code
D6500 Mode
Modem IIIa2Code
Bosch SIA Mode
Contact ID Event Contact ID
Code
A point supervisory
condition occurred
Jsppp NriaBSppp 24 hour Non-Burglary 1 150 00 000
A valid local access
occurred
RsF01 NLS Successful Download/Access 1 412 00 000
A valid remote access
callback occurred
RsssF NphhhRS Successful Download/Access 1 412 00 000
A valid remote access
occurred
RsssF NRS Successful Download/Access 1 412 00 000
AC Fail – mains power
supply
Pssss NAT AC Loss 1 301 00 000
AC Restore – mains
power supply
Rsss0 NAR AC Loss 3 301 00 000
Access Denied – Door
Secured
ADsppp Nria/idiiiDZppp or
Nria/idiii/
ssxDZppp
Access Denied 1 421 aa uuu
Access Denied –
Interlocked
ADsppp Nria/idiiiDWppp or
Nria/idiii/
ssxDWppp
Access Denied 1 421 aa uuu
Access Denied – No rights
in area by card
ADsppp Nria/idiiiDVppp or
Nria/idiii/
ssxDVppp
Access Denied 1 421 aa uuu
Access Denied – Unknown
ID
ADsppp NriaDDppp Access Denied 1 421 aa uuu
Access Granted AGsppp Nria/idiiiDGppp or
Nria/idiii/
ssxDGppp
Access Report by User 1 422 aa uuu
Alarm Asppp NriaBAppp Burglary 1 130 aa ppp
Alarm Cross Point Asppp NriaBMppp Burglary 1 130 aa ppp
Alarm Exit Error Asppp Nria/idiiiEAppp Entry/Exit 1 134[2] aa ppp
Alarm with Recent Closing Asppp Nria/CRppp Entry/Exit 1 134[2] aa ppp
All SDI devices are
missing, power is shorted
TsssD NpidddET Expansion Module Failure 1 333 00 000
All SDI devices are
restored, power is normal
RsssD NpidddER Expansion Module Failure 3 333 00 000
An individual SDI device is
missing.
TsssD NpidddEM Expansion Module Failure 1 333 00 000
An individual SDI device is
restored.
RsssD NpidddEN Expansion Module Failure 3 333 00 000
An invalid remote access
callback occurred
TsssF NphhhRU Unsuccessful Access 1 413 00 000
An invalid remote access
occurred
TsssF NRU Unsuccessful Access 1 413 00 000
Armed perimeter delay Csiii Nria/idiiiNL Armed STAY 3 441 aa uuu
Armed perimeter instant Csiii Nria/idiiiNL Armed STAY 3 441 aa uuu
Bypass by Remote Nsppp NriaUBppp Zone/Sensor Bypass 1 570 aa ppp
Bypass by SDI device Nsppp Nria/pidddUBppp Zone/Sensor Bypass 1 570 aa ppp
Bypass by Sked Nsppp Nria/aikkkUBppp Zone/Sensor Bypass 1 570 aa ppp
Bypass by User Nsppp Nria/idiiiUBppp Zone/Sensor Bypass 1 570 aa ppp
Bypass Point Nsppp NriaUBppp Zone/Sensor Bypass 1 570 aa ppp

D9412GV3/D7412GV3/D7212GV3 Reporting Format Definitions | en 21
Bosch Security Systems, Inc. Quick Reference Guide F01U170805 | 01 | 2010.11
Checksum failure on
configuration memory
TsD15 NYF RAM Checksum Bad 1 303 00 000
Closing by Area Csiii Nria/idiiiCL O/C by User 3 401 aa uuu
Closing Early by Area Csiii Nria/idiiiCK Early O/C 3 451 aa uuu
Closing Late by Area Csiii Nria/idiiiCJ Late O/C 3 452 aa uuu
Communication failure by
route group
TsB01 NrggYC Failure to communicate event 1 354 00 000
Communication failure by
route group restored
NsB01 NrggYK Failure to communicate event 3 354 00 000
Communication trouble
by network
TsB01 Nrgg/pidddYS Communication Trouble 1 350 00 000
Communication trouble
by network restored
NsB01 Nrgg/pidddYK CommunicationTrouble 3 350 00 000
Communication trouble
by phone
TsB01 NphhhYS Communication Trouble 1 350 00 000
Communication trouble
by phone restored
NsB01 NphhhYK Communication Trouble 3 350 00 000
Control panel battery low Tsss9 NYT Low System Battery 1 302 00 000
Control panel battery
missing
Tsss9 NYM Battery Missing/Dead 1 311 00 000
Control panel battery
restored to normal
Rsss9 NYR Low System Battery 3 302[6] 00 000
Create Status Report Sssss NYY Status Report to Follow 1 605 00 000
Date changed – no user
identified
NsD07 NJD Time/Date Reset 1 625 00 000
Dated changed by user NsD07 NidiiiJD Time/Date Reset 1 625 00 uuu
Door Closed, Restoral Rsppp NriaDHppp Access Door propped open 1 426 aa ppp
Door Left Open Alarm Asppp NriaDLppp Access Door propped open 1 426 aa ppp
Door Left Open Trouble Tsppp NriaDMppp Access Door propped open 1 426 aa ppp
Duress Dsiii Nria/idiiiHA Duress 1 121 aa uuu
Event Log Overflow AsD01 NJO Event Log Overflow 1 624 00 000
Event Log Threshold has
been reached
TsD01 NJL Event Log 90% Full 1 623 00 000
Extend Close Time TsD26 Nria/idiii/
tihhmmCE
Auto-arm Time Extended 1 464 aa uuu
Extra Point Tsppp NriaXEppp Maintenance Alert 1 393 aa ppp
Fail To Close by Area TsssE NriaCI Failed to Close 1 454 aa 000
Fail To Open by Area TsssE NriaOI Failed to Open 1 453 aa 000
Fire Alarm Fsppp NriaFAppp Fire 1 110 aa ppp
Fire Cancel \siii Nria/idiiiFC Cancel 1 406 aa ppp
Fire Missing Msppp NriaFYppp Fire Trouble 1 373 aa ppp
Fire Restoral from Alarm Hssppp NriaFHppp Fire 3 110 aa ppp
Fire Restoral from Trouble Hsppp NriaFJppp Fire Trouble 3 373 aa ppp
Fire Supervision Esppp NriaFSppp Fire Supervisory 1 200 aa ppp
Fire Supervision from
Restore
Esppp NriaFVppp Fire Supervisory 3 200 aa ppp
Fire Trouble Gssppp NriaFTppp Fire Trouble 1 373 aa ppp
Fire Walk Test End RsssF Nria/idiiiFK Fire Test 3 604 aa uuu
Fire Walk Test Start TsssF Nria/idiiiFI Fire Test 1 604 aa uuu
Force Armed Perimeter
Delay
Csiii Nria/idiiiNF Partial Arm 3 456 aa uuu
Modem IIIa2Event Modem IIIa2Code
D6500 Mode
Modem IIIa2Code
Bosch SIA Mode
Contact ID Event Contact ID
Code