Bosch ICP-EZM2 User manual

Easy Series Control Panel
ICP-EZM2
en Quick Start Guide

Table of contents
1Install the Enclosure 4
2Wire the Control Panel 6
3Configure the System 8
3.1 Configuring with the telephone 8
3.2 Configuring with RPS 8
4Add/Change Users 10
4.1 Add users 10
4.2 Change users 10
5System Test and Maintenance 11
6Installer Telephone Menu 12
7Appendix 13
7.1 Expert Programming 13
7.2 Country Codes 23
7.3 Default Passcodes 23
Easy Series Control Panel Table of Contents | en 3
Bosch Security Systems, Inc. Quick Start Guide 2014.09 | 01 | F.01U.306.216

Install the Enclosure
Refer to Figure 1.1 for the suggested placement of system components in the enclosure.
Notice!
Use proper anchor and screw sets when installing the enclosure on non-load-bearing
surfaces, such as drywall.
Follow anti-static procedures when handling the control panel board. Touch the earth ground
terminal on the control panel board to discharge any static charge before working on the
control panel board.
If you install more than one control center, mount them at least 1.2 m apart.
Do not install the RADION receiver within 15 cm (6 in) of the control centers metal enclosure.
12 VDC
2
3
4
5
6
1
7
Figure 1.1: System component placement in enclosure
1
4en | Install the Enclosure Easy Series Control Panel
2014.09 | 01 | F.01U.306.216 Quick Start Guide Bosch Security Systems, Inc.

Callout Description
1 Port for ICP-EZPK programming key and ICP-EZRU2-V3
Update Key
2 ICP-EZTS Cover and Wall Tamper Switch
3 Ground connection
Connect ground wire from enclosure to enclosure door.
4 Module mounting location
5 Module mounting location
6 Status LED (√)
System Test Button (→)
7 Port for ICP-EZV2 Voice Module
Easy Series Control Panel Install the Enclosure | en 5
Bosch Security Systems, Inc. Quick Start Guide 2014.09 | 01 | F.01U.306.216

Wire the Control Panel
Refer to Figure 2.1 for an overview of the system components and wiring.
IUI-EZ1
1
B
G
Y
R
RFRC-OPT
2
B
G
Y
R
DX2010
3
B
G
Y
R
+
-
9
(+) (-)
10
7
8
B
G
Y
R
B426 6
B
G
Y
R
B450
4
5
11
12
(+) (-)(+) (-)(+) (-)
(+)
(-)
(+)(+)
(+) (-)
+
(-)
(+)
(-)
Figure 2.1: Wiring diagram
Callout Description
1Control Center Mount within 3 m of control panel, Use
CAT5 cable (twisted pair) for audio
bus, Set data bus address (1 - 4), up to
4 controls max
2RADION receiver 1 = Normal Operation
5 = Maintenance Mode
3DX2010 Point
Expander
Data bus Adr 102: Points 9-16
Data bus Adr 103: Points 17-24
Data Bus Adr 104: Points 25-32
2
6en | Wire the Control Panel Easy Series Control Panel
2014.09 | 01 | F.01U.306.216 Quick Start Guide Bosch Security Systems, Inc.

Callout Description
4B426 Network
Interface Module
Use address 6.
5B450 Conettix
Plug-in
Communicator
Use address 6.
6Supervised Points
(single EOL)
Normally open and normally closed options (2.2k Ω)
7Supervised Points
(dual EOL)
Normally closed (2.2k Ω)
8Keyswitch Options (single and dual EOL) ((2.2k Ω)
9
Prog Output (PO) 1
Options
Switched 12v Switched Ground Dry Contact
10 Prog Outputs 2 - 4 NF A2P requires that sirens have a backup battery. When this
siren requires a 14,1V to 14,4V supply, use the optional board
EZPS-FRA or the auxiliary power supply IPP-PSU-2A5. Set the
output as interior burglary alarm.
11 2-wire Smoke
Detector Option
EOL resistor (P/N: 25899) required.
12 4-wire Smoke
Detector Option
EOL resistor (P/N: 25899) and Bosch EOL relay module
required
Note: The system uses a 12 VDC battery, connected as shown.
If using RADION devices:
1. Mount the bases for the wireless devices in the desired locations.
Do not attach the wireless devices to the bases at this time.
2. Remove all power from the system.
3. Set the switch on the RADION receiver to normal operating mode = 1.
4. Reapply system power.
Wait for the solid green circle to appear on the control center.
5. Enter the Installer Telephone Menu. Refer to Configuring with the telephone, page 8.
Easy Series Control Panel Wire the Control Panel | en 7
Bosch Security Systems, Inc. Quick Start Guide 2014.09 | 01 | F.01U.306.216

Configure the System
Configure the system using one of the methods described in this section for your control
panel type.
Configuring with the telephone
Refer to Installer Telephone Menu, page 12 for the complete programming menu.
Basic Programming:
1. Enter the Installer passcode (default: 4-digit 5432, 6-digit 543211).
2. Press [3] to enter the Basic Programming menu to make the following changes:
– Modify point types [1][2].
– Record point descriptions [1][1].
– Enter an account number [2][1].
3. Press [#][#][#] to exit Basic Programming.
4. Press [1] to enter System Maintenance to configure wireless devices.
5. Select Wireless Configuration [6] from the System Maintenance menu.
6. After the system prompt, enter the point number (1 to 32) that you want to configure.
The control panel announces the point number and the point type.
If the point number is not currently assigned to a Wireless ID:
To set Point Type, press [1].
To add a device, press [2].
Press [#] to exit.
If the point number is currently assigned to a Wireless ID:
To set Point Type press [1].
To replace a device, press [3]
To delete this device, press [4].
Press [#] to exit.
1. Press [#][#] to exit to the main menu.
2. Press [2] to enter the User Menu to change the installer passcode.
3. Press [1] and change the Installer Passcode.
4. Press [#][#] to exit the User Menu.
Configuring with RPS
In addition to the Installer Phone Menu, you may use RPS to configure an Easy Series control
panel with RADION support. To configure RADION wireless points, specify the following
information for each point:
– Device Type
– Point Type
– Wireless Point ID
– Wireless Alarm Inputs
Since Wireless Alarm Inputs is only available in “Expert Mode”, you must use Expert Mode to
properly configure the Easy Series control panel for RADION wireless devices.
The following table shows the correlation between the current RPS Device Type values and
the RADION Device Types.
1. Once the device type has been selected in RPS, enter the Wireless Point ID and Point
Type via the “wizard” dialog.
3
3.1
3.2
8en | Configure the System Easy Series Control Panel
2014.09 | 01 | F.01U.306.216 Quick Start Guide Bosch Security Systems, Inc.

2. Enter the RFID for the point as specified in the product packaging.
3. Select the desired Point Type from the drop-down menu.
4. Enter an appropriate value in the Wireless Alarm Inputs column.
When setting up an Easy Series control panel to use RADION transmitters, only select from the
RPS device types listed in the table below.
RPS device type RADION transmitter Wireless alarm inputs
PIR motion detector PIR detector (RFPR-12)
PIR curtain detector (RFPR-
C12)
Motion
Dual motion detector Motion detector (RFDL-11) Motion
Wireless device type 3 Repeater (RFRP) None
Smoke detector Smoke detector (RFSM) Smoke
Door Window contact sensor Universal transmitter (RFUN) Wired or magnet
Glass break sensor Glassbreak detector (RFGB) Glass break
Wireless Recessed Point Recessed door/window
contact (RFDW-RM)
Magnet
Wireless Bill Clip Bill trap (RFBT) Magnet
Mini-Door-Window contact Door/window contact (RFDW-
SM)
Magnetic
Notice!
Do not use any other RPS device types when specifying RADION transmitter configurations.
The columns labeled “Wireless Sensor Sensitivity” and “External Power Input” have no effect
on the Radion Wireless Receiver/Transmitter configuration. These fields are not used by the
Easy Panel Radion configuration.
Easy Series Control Panel Configure the System | en 9
Bosch Security Systems, Inc. Quick Start Guide 2014.09 | 01 | F.01U.306.216

Add/Change Users
Enter the User Telephone Menu
1. Connect to the phone test posts or use the house phone.
+
2. Hold down the test button for 10 seconds.
3. Enter the Master Passcode default 1234(55).
Add users
Add Users
1. Enter the User Telephone menu.
2. Enter the Master User (User 1) passcode
3. Press [4] to enter the user menu.
4. Press [1] to add a new user
5. Repeat step 4 for additional users.
Press [#] to return to the User Menu, or [#][#][#] to exit completely.
Change users
Change Users
1. Enter the User Telephone Menu.
2. Enter the Master User (User 1) passcode.
3. Press [4] to enter the User Menu.
4. Press [2] to change a user. Press [2] repeatedly until the system speaks the desired user
number.
5. Repeat Step 4 in Add Users.
6. Press [#] to return to the User Menu, or [#][#][#] to exit completely.
4
4.1
4.2
10 en | Add/Change Users Easy Series Control Panel
2014.09 | 01 | F.01U.306.216 Quick Start Guide Bosch Security Systems, Inc.

System Test and Maintenance
Test the system for proper operation when installation and configuration are complete.
4Press the System Test button on the control panel board for one sec. The system
provides instructions throughout the test. Follow all instructions.
4Contact the central monitoring station (CMS) to verify that all necessary test reports
were received, including test reports from all installed input and output devices.
Notice!
After system installation and any control panel programming, perform a complete system test.
A complete system test includes testing the control panel, all devices, and communication
destinations for proper operation.
5
Easy Series Control Panel System Test and Maintenance | en 11
Bosch Security Systems, Inc. Quick Start Guide 2014.09 | 01 | F.01U.306.216

Installer Telephone Menu
1. Connect to the phone test posts or use the house phone.
+
2. Hold down the test button for 10 seconds.
3. Enter the Master Passcode default 1234(55).
Basic
Programming
User Menu
System
Maintenance
Event history
System test menu
Set date and time
Full system test
Reset system
Exit
1
Wireless configuration
1
2
3
5
6
#
Exit
Warning device test
Battery test
Communication test
Control center test
Point test
Operate Outputs
2
3
4
5
6
#
1
Exit
Most recent events
Events by date
Last alarm event
Last 10 events
2
3
4
#
1
4
2
Change installer passcode
Change master user (User 1) passcode
Exit user menu
2
#
1
Installer
Passcode
3
Points
Report
configuration
2
1
Record point description
Set point type
Exit
2
#
1
Enter account number
Configure report destinations
Remote programming success
Exit
2
3
#
1
Exit
Outputs
Country code
3
4
#
Select output function
Exit
#
1
Expert
Programming
4Enter programming item, enter selection.
Two-Way
Voice Session
5
Talk to person at control center
Listen to person at control center
Exit
2
#
1
Custom
Messages
6
Record site description
Record Call for Service message
Exit
2
#
1
Programming
Key
7
Send data from key to control panel
Send data from control panel to key
Exit
2
#
1
#Exit
Exit
Set point type
Add a device
Delete a device
Replace a device
2
3
4
#
1
Expert diagnostic menu
7
Exit
Signal level summary
Messages and packets received
Signal level in percentage
Filtered ambient signal level in percentage
Realtime ambient signal level in percentage
2
3
4
5
#
1
6
12 en | Installer Telephone Menu Easy Series Control Panel
2014.09 | 01 | F.01U.306.216 Quick Start Guide Bosch Security Systems, Inc.

Appendix
Expert Programming
System Programming Items
Item
No.
Programming Item Range
102 Country Code 00 to 99(see Country Codes, page 23)
103 Enclosure Tamper
Enabled
0 = Disabled
1 = Enabled
107 Fire Bell Cut-Off Time 0 to 90 min
108 Intrusion Bell Cut-Off
Time
0 to 90 min
110 Intrusion Abort
Window
15 to 45 sec
111 Fire Alarm Cancel
Window
0 to disable, 1-10 min
112 Intrusion Cancel
Window
5 to 10 min
114 Chime Tone Select 1, 2, or 3
115 Chime Mode
Operation After
System Off
0 = Off
1 = On
2 = Follows previous setting
116 Automatic Test
Frequency Report
0 = Off
1 = Daily
2 = Weekly
3 = Monthly
119 EN50131 Level 4
Access Code
6-digit numerical passcode (0-9)
121 Daylight Saving Time 0 = Off
1 = North America (pre 2007)
2 = Europe & Asia
3 = Tasmania, Australia
4 = Rest of Australia
5 = New Zealand
6 = Cuba
7 = South America & Antarctica
8 = USA (post 2006)
122 Installer Passcode
Override
0 = Disabled
1 = Enabled
7
7.1
Easy Series Control Panel Appendix | en 13
Bosch Security Systems, Inc. Quick Start Guide 2014.09 | 01 | F.01U.306.216

System Programming Items
Item
No.
Programming Item Range
124 Point Alarm
Verification
0 = Off
1 = Cross Zone
2 = Intelligent Threat Assessment
3 = Confirmed Alarms 1 (initial entry door)
4 = Confirmed Alarms 1 (token, key fob, or
keyswitch)
125 Faulted Points
Allowed Threshold
0 to 8
126 Exit Delay 0 to 255 sec
127 Entry Delay 0 to 255 sec
129 Recent Close Enabled 0 = Report not sent
1 = Report sent
131 Swinger Bypass Count 0 to disable, 1-15
133 System On Order
Options
1 to 6
134 Cross Zone Timer 0 to 3600 sec
136 Clear Alarm Memory 0 = By any user
1 = By master user only
140 Demo Mode 0 = The system only speaks all telephone
messages over the phone.
1 = The system speaks all telephone
messages over the phone and at all control
centers connected to the system.
2 = During telephone programming, press
the [i] button to turn message
announcements on or off at the control
center.
142 Restrict Installer
Passcode
0 = Master user not needed
1 = Master user needed
151 Wireless Device
Supervision Interval
1= 1 Hour
2= 2 Hours
3= 4 Hours
4= 12 Hours
5= 24Hours
6= 2.5 Hours
162 Missing Wireless
Device Conditions
0 = Missing conditions create a tamper
condition (meets EN50131).
1 = Missing conditions create a trouble
condition.
14 en | Appendix Easy Series Control Panel
2014.09 | 01 | F.01U.306.216 Quick Start Guide Bosch Security Systems, Inc.

System Programming Items
Item
No.
Programming Item Range
163 Silence Trouble Tones 0 = All trouble tones beep at the control
center.
1 = Only Fire and 24-Hour trouble tones
beep at the control center.
164 System Inactivity Time
(Hours)
Enter the number of hours (0-255) that the
system must be off before it sends the
System Inactive report.
165 System Inactivity Time
(Days)
Enter the number of days (0-255) that the
system must be off before it sends the
System Inactive report.
166 System Inactivity Time
(Weeks)
Enter the number of weeks (0-255) that the
system must be off before it sends the
System Inactive report.
167 Force Arm/Exit Error 0 = Off-normal points create an exit error at
the end of Exit Delay
1 = Off-normal points are force-armed at the
end of Exit Delay
168 Audio Verification
Command Set
0 = Use SIA Standard Audio Verification
commands (AV-01-1997.11)
1 = Use alternate audio verification
command set
601 Enable Keyfob Duress 0 = Wireless keyfob does not send a Duress
event
1 = Wireless keyfob sends a Duress event
Audio Verification Commands
SIA Standard Audio Verification Commands (Item No. 168 = 0)
Phone Button Command
[1] Talk to premises.
[3] Listen to premises.
[6] Listen to premises.
[7] Restart 90-second timer.
[9][8] Terminate session with call back.
[9][9] Terminate session without call back.
[0] Listen to all microphones.
[#] Cancels first digit of command.
Easy Series Control Panel Appendix | en 15
Bosch Security Systems, Inc. Quick Start Guide 2014.09 | 01 | F.01U.306.216

SIA Standard Audio Verification Commands (Item No. 168 = 0)
Phone Button Command
Alternate Audio Verification Commands (Item No. 168 = 1)
Phone Button Command
[#] Talk to premises.
[*] Listen to premises.
[7] (any number 1 to 9) Restart 90-second timer.
[0] Terminate session without call back.
Route Destination Items
Item
No.
Programming Item Range
100 Account Number 4- or 6-digit number
201 Phone Line Supervision 0 = On
1 = Off
202 PSTN, IP or Cellular
Connection
0 = PSTN telephone line
1 = B426, B450
205 Dial Tone Detect 0 = On
1 = Off
Phone Number/IP Address for Route Destination:
206 Route 1 Primary 32 digits maximum
0-9, B-F allowed.
. = [*] (. between each IP address
notation).
Exit with save = [#]
Exit without save = [#][#]
Disable phone number = [0][#]
Disable IP address = 240.0.0.0
207 Route 1 Backup
208 Route 2 Primary
209 Route 2 Backup
210 SMS Service Provider No.
Format for Route Destination:
211 Route 1 Primary 0 = Disabled
1 = Contact ID
2 = SIA
3 = Voice
4 = SMS
5 = Fast Format
6 = Network
212 Route 1 Backup
213 Route 2 Primary
214 Route 2 Backup
215 Call Waiting Disable 3 or 4 digits
* = [*][*]; # = [*][#]
216 Emergency Call Override
No.
3-digit number
16 en | Appendix Easy Series Control Panel
2014.09 | 01 | F.01U.306.216 Quick Start Guide Bosch Security Systems, Inc.

Route Destination Items
Item
No.
Programming Item Range
217 Emergency Call Override
No. Delay
0 to 60 min
218 Auto Detect Pulse Dial 0 = Tone dialing
1 = Pulse dialing
222 Phone Answer Ring Count 1 to 255 rings
Alternate Communication Items
Item
No.
Programming Item Range
Port Number for Route Destination:
241 Route 1 Primary 0 to 65535
242 Route 1 Backup
243 Route 2 Primary
244 Route 2 Backup
Heartbeat for Route Destination:
281 Route 1 Primary 0 = Disabled; 1 to 65535 min
282 Route 1 Backup
283 Route 2 Primary
284 Route 2 Backup
Acknowledge Wait Time for Destination:
285 Route 1 Primary 5 to 255 sec
286 Route 1 Backup
287 Route 2 Primary
288 Route 2 Backup
Anti-Replay for Route Destination:
289 Route 1 Primary 0 = Disabled; 1 = Enabled
290 Route 1 Backup
291 Route 2 Primary
292 Route 2 Backup
Heartbeat Attempt for Route Destination:
293 Route 1 Primary 1 to 99
294 Route 1 Backup
295 Route 2 Primary
Easy Series Control Panel Appendix | en 17
Bosch Security Systems, Inc. Quick Start Guide 2014.09 | 01 | F.01U.306.216

Alternate Communication Items
Item
No.
Programming Item Range
296 Route 2 Backup
297 Extend Heartbeat Period 0 = Disabled; 1 to 255 min
RPS Configuration Items
Item
No.
Programming Item Range
118 RPS Passcode 6 digits required, using 0 to 9
and A to F.
224 RPS Automatic Call In Frequency 0 = Never; 1 = Daily
2 = Weekly; 3 = Monthly
225 RPS Automatic Call In Time
(Hours)
0 to 23
226 RPS Automatic Call in Time
(Minutes)
0 to 23
227 RPS Automatic Call in Time (Day
of Week)
0 to 6, where 0 = Sunday and 6
= Saturday
228 RPS Automatic Call in Time (Day
of Month)
1 to 28
229 RPS Automatic Call in Phone
Number/IP Address
Refer to Item Numbers 206-209
for allowed entries.
245 RPS Automatic Call in Method 0 = Phone number; 1 = IP
address
246 RPS Port Number 0 to 655353
Point Report and Restoral Routing
Item
No.
Programming Item Item
No.
Programming Item
301 Point Reports and
Restorals(all)
326 Intrusion Zone Bypass
307 Intrusion Alarm 327 Intrusion Zone Bypass
Restoral
308 Intrusion Alarm Verified 328 Fire Trouble
309 Intrusion Alarm Unverified 329 Fire Trouble Restoral
310 Intrusion Alarm 24-Hr 331 24-Hour Trouble
311 Intrusion Alarm 24-Hr
Restoral
332 24-Hour Trouble Restoral
312 Intrusion Alarm Restoral 335 Supervisory Alarm
18 en | Appendix Easy Series Control Panel
2014.09 | 01 | F.01U.306.216 Quick Start Guide Bosch Security Systems, Inc.

Point Report and Restoral Routing
Item
No.
Programming Item Item
No.
Programming Item
313 Duress 336 Supervisory Alarm Restoral
315 Fire Alarm 371 Fire Cancel
316 Fire Alarm Unverified 388 Point Tamper
317 Fire Alarm Restoral 393 Cross Zone Trouble
318 Panic 394 Alarm Recent Close
323 Cancel 399 Panic Restoral
324 Intrusion Trouble 400 Cross Zone Trouble Restoral
325 Intrusion Trouble Restoral
Range: 0 = Neither Route, 1 = Route 1 only, 2 = Route 2 only, 3 = Both
routes
System On and Off (Open and Close) Report Routing
Item
No.
Programming Item Item
No.
Programming Item
302 System On and Off Reports
(all)
341 Open
314 Exit Error 342 Open Keyswitch
330 Recent Closing 343 Open Remote
337 Close (System On)
Unoccupied
344 Close (System On) Custom
338 Close (System On)
Occupied
386 Open by Guard Code
339 Close Keyswitch 403 Partial Close (System On)
340 Close Remote
Range: 0 = Neither Route, 1 = Route 1 only, 2 = Route 2 only, 3 = Both
routes
System Report and Restoral Routing
Item
No.
Programming Item Item
No.
Programming Item
303 System Reports and
Restorals (all)
358 Low Battery
319 User Emergency 359 Low Battery Restoral
320 User Fire 364 Phone Line Fault Restoral
321 User Fire Restoral 372 Firmware Updated
Easy Series Control Panel Appendix | en 19
Bosch Security Systems, Inc. Quick Start Guide 2014.09 | 01 | F.01U.306.216

System Report and Restoral Routing
Item
No.
Programming Item Item
No.
Programming Item
322 User Panic 375 ROM Fault
345 AC Fail 376 Bell Trouble
346 AC Fail Restoral 377 Bell Restoral
347 Auto System Test Normal 378 Walk Test End
348 Auto System Test Off-
Normal
379 Walk Test Start
349 Auxiliary Power Fault 380 Bus Device Missing
350 Auxiliary Power Restoral 381 Bus Device Missing Restoral
351 Communication Fail 382 Battery Missing
352 Communication Restoral 383 Battery Missing Restoral
353 Control Center Supervision
Fail
384 RAM Checksum Failed
354 Control Center Supervision
Restoral
385 System Inactive
355 Control Center Tamper 391 Passcode Tamper
356 Control Center Tamper
Restoral
392 Watchdog Reset
357 Local Programming Success 410 Date/Time Changed
362 Communication Test
Manual
413 Network Fail
363 Phone Line Fault 414 Network Restoral
Range: 0 = Neither Route, 1 = Route 1 only, 2 = Route 2 only, 3 = Both
routes
Global Report Routing Items
Item
No.
Programming Item Range
304 Communicator Disable 0 = Enable reporting
1 = Disable reporting
305 Route Attempts 1 to 20
306 Send Report During Walk Test 0 = No
1 = Yes
20 en | Appendix Easy Series Control Panel
2014.09 | 01 | F.01U.306.216 Quick Start Guide Bosch Security Systems, Inc.