Bosch ICP-SOL2-P User manual

Control Panel
ICP-SOL2-P/ICP-SOL3-P
en Installation Guide

Table of contents
1Introduction 8
1.1 About documentation 8
1.2 Related documentation 8
1.3 Bosch Security Systems, Inc. product manufacturing dates 9
2System Overview 10
2.1 ICP-SOL2-P 10
2.2 ICP-SOL3-P 12
2.3 Configuration and Parts 13
2.3.1 Control panel capacities 13
2.3.2 Parts list 14
2.3.3 Order separately 14
3Installation workflow 15
4Accessories 16
4.1 Codepads 16
4.1.1 Icon Codepad Indicators 18
4.1.2 Text Codepad Indicators 19
4.1.3 Installer Menu 23
4.1.4 User Menu 26
4.1.5 All - No PIN menu 26
4.2 RADION keyfobs 27
4.3 Keyswitches 27
4.4 B308 Octo-output Module 28
4.5 WE800EV2 29
4.6 B810 receiver 30
4.7 RADION repeater 30
4.8 RADION detectors 30
4.9 A-Link Plus Software 30
4.9.1 Connect to the control panel remotely 32
4.9.2 Options 34
4.9.3 Communicating with the B426/B450 35
4.10 B426 Conettix Ethernet Communication Modules 38
4.11 B450 Conettix Plug-in Communicator Interfaces 38
4.12 Using the network communication modules 39
4.13 TF008 Plug Pack (TF008-B) 40
4.13.1 Install the transformer 40
4.14 Remote Security Control 40
5Configuration 42
5.1 Installer Commands 42
5.1.1 Command 958 - Exit from Installer's Programming Mode without saving changes 42
5.1.2 Command 959 - Test the IUI-SOL-ADAPTER 42
5.1.3 Command 960 - Save and exit from Installer's Programming Mode 43
5.1.4 Command 961 - Reset the Control Panel to Factory Default Settings 43
5.1.5 Command 962 - Copy the Control Panel Memory to the IUI-SOL-ADAPTER 43
5.1.6 Command 963 - Copy the IUI-SOL-ADAPTER to the Control Panel 43
5.1.7 Command 965 - Set up Domestic Dialing Format 44
5.1.8 Command 966 - Enable/Disable the Automatic Stepping of Locations 45
5.1.9 Command 999 - Display the Software Version Number 45
Control Panel Table of Contents | en 3
Installation Guide 2014.07 | 00n | F01U298026

5.2 Disable Factory Defaults 46
5.3 Configuring for email 47
6System Operations 52
6.1 Arming the system in AWAY Mode 52
6.2 Disarming the system from AWAY Mode 52
6.3 Arming the System in STAY Mode 1 53
6.4 Disarming the system from STAY Mode 1 54
6.5 Arming the system from STAY Mode 2 54
6.6 Disarming the system from STAY Mode 2 55
6.7 Codepad duress alarm 56
6.8 Codepad panic alarm 56
6.9 Codepad fire alarm 56
6.10 Codepad medical alarm 56
6.11 Isolating zones 56
6.12 Standard isolating 57
6.13 Code to isolate 57
6.14 Fault analysis mode 58
6.15 Fault descriptions 59
7System Functions 62
7.1 Installer Code Functions 62
7.1.1 Add or Delete RF Wireless Devices 62
7.1.2 Set the Number of Days until the First Test Report 63
7.1.3 Change Domestic Phone Numbers 64
7.1.4 Change Telco Arm/Disarm Sequence 65
7.1.5 Setting STAY Mode 2 Bypass Zones 66
7.1.6 Turning Report Monitor Mode On and Off 67
7.1.7 Walk Test Mode 68
7.1.8 Event Memory Recall Mode 68
7.2 Master Code Functions 69
7.2.1 Arm or Disarm both Areas at the Same Time 69
7.2.2 Changing and Deleting User Codes 70
7.2.3 Changing and Deleting Remote Radio User Codes 70
7.2.4 Deleting User/Radio Codes 71
7.2.5 Change Domestic Phone Numbers 71
7.2.6 Change Telco Arm/Disarm Sequence 73
7.2.7 Setting STAY Mode 2 Bypass Zones 74
7.2.8 Turning Outputs On and Off 75
7.2.9 Setting the Date and Time 75
7.2.10 Walk Test Mode 76
7.2.11 Event Non-Volatile Memory Recall Mode 76
7.3 User Code Functions 77
7.4 Hold-Down Functions 77
7.4.1 Arm the System in AWAY Mode 77
7.4.2 Arm the System in STAY Mode 1 78
7.4.3 Arm the System in STAY Mode 2 78
7.4.4 Horn Speaker Test 78
7.4.5 Bell Test 78
7.4.6 Strobe Test 78
7.4.7 Turning Day Alarm On and Off 78
4en | Table of Contents Control Panel
2014.07 | 00n | F01U298026 Installation Guide

7.4.8 Fault Analysis Mode 79
7.4.9 Initiate a Modem Call 79
7.4.10 Reset Latching Outputs 79
7.4.11 Change the Codepad Buzzer Tone 79
7.4.12 Send Test Report 80
8Domestic Dialing 81
8.1 Domestic Dialing Funtion 81
8.2 Setting Up and Programming Domestic Reporting 81
9Zone Information 83
9.1 Day Alarm Information 83
9.1.1 Day Alarm Resetting 83
9.1.2 Day Alarm Latching 83
9.1.3 Day Alarm Operation 83
9.2 EOL Resistor Value 84
9.3 Zone Programming 85
9.3.1 Zone Defaults 86
9.3.2 Zone Types 90
9.3.3 Zone Pulse Count 92
9.3.4 Zone Pulse Count Time 92
9.3.5 Zone Options 1 93
9.3.6 Zone Options 2 94
9.3.7 Zone Report Options 95
9.3.8 Keyswitch Zone Options 95
9.4 Swinger Shutdown Count for Siren 97
9.5 Swinger Shutdown Count for Report 97
9.6 System Status Programming 98
9.6.1 System Status Reporting Options 98
9.6.2 Test Reporting Time 98
9.6.3 Test Reporting Options 99
9.7 STAY Mode 2 Automatically Bypass Zones 99
10 System Event Timers 101
10.1 Programming Entry/Exit Timers 101
10.2 Entry Timer 1 101
10.3 Entry Timer 2 101
10.4 Exit Timer 101
10.5 Entry Guard Timer for STAY Mode 102
10.6 Delay Alarm Reporting Time 102
10.7 Sensor Watch Time 102
10.8 Codepad Lockout Time 103
10.9 Siren Run Time 103
10.10 Siren Sound Rate 103
10.11 Auto Arming Pre-Alert Timer 103
10.12 Auto Arming Time 104
10.13 Auto Disarming Time 104
10.14 Kiss-Off Wait Time 105
10.15 Speaker Beep Volume 105
11 System and Consumer Options 106
11.1 System Options 1 106
11.2 System Options 2 106
Control Panel Table of Contents | en 5
Installation Guide 2014.07 | 00n | F01U298026

11.3 System Options 3 107
11.4 System Options 4 108
11.5 Consumer Options 1 108
11.6 Consumer Options 2 109
11.7 Consumer Options 3 110
12 Partitioning 111
12.1 Programming 111
12.1.1 Partitioning Options 1 111
12.1.2 Partitioning Options 2 111
12.2 Zone allocations 112
12.2.1 Zone area assignments 112
12.2.2 User code area assignments 113
12.2.3 Codepad assignment 113
13 Communicator Information 114
13.1 Primary Telephone Number for Receiver 1 and Receiver 2 115
13.2 Secondary Telephone Number for Receiver 1 and Receiver 2 115
13.3 Transmission Format for Receiver 1 and Receiver 2 115
13.4 Subscriber ID Number for Receiver 1 and Receiver 2 116
13.5 Telco Arming Sequence 116
13.6 Telco Disarming Sequence 117
13.7 Call Back Telephone Number 117
13.8 Ring Count 117
13.9 Telephone Line Fail Options 118
13.10 Communicator Options 1 119
13.11 Communicator Options 2 120
13.12 Communicator Options 3 121
13.13 A-Link Options 121
13.14 Sending reports with the network modules 122
14 Access 124
14.1 Installer Code 124
14.2 User Codes 124
14.3 User Code Priority 126
15 Programmable Outputs 128
15.1 Output Programming 128
15.2 Output Event Types 132
15.3 Output Polarity 138
15.4 Output Timing 140
15.5 Pulsing Polarities 140
15.6 One-Shot Polarities 140
16 RF Information 141
17 Reports 142
17.1 Zone Tamper Report 142
17.2 Walk Test Report 142
17.3 Bypass Report 142
17.4 Trouble Report 142
17.5 Sensor Watch Report 142
17.6 Alarm Restore Code 143
17.7 RF Receiver Trouble Report 143
17.8 RF Receiver Trouble Restore Report 143
6en | Table of Contents Control Panel
2014.07 | 00n | F01U298026 Installation Guide

17.9 RF Low Battery Report 143
17.10 Arm/Disarm Reports 143
17.11 Codepad Duress Report 143
17.12 Codepad Panic Report 144
17.13 Codepad Fire Report 144
17.14 Codepad Medical Report 144
17.15 AUX Power Supply Fail Report 144
17.16 AUX Power Supply Fail Restore Report 144
17.17 AC Fail Report 144
17.18 AC Fail Restore Report 144
17.19 Low Battery Report 144
17.20 Low Battery Restore Report 145
18 Strings 146
18.1 Fault String 146
18.2 Event String 147
Control Panel Table of Contents | en 7
Installation Guide 2014.07 | 00n | F01U298026

Introduction
This section includes an introduction to documents for this product and other document-
related instructions.
About documentation
This document contains instructions for a trained installer to properly install, configure, and
operate this control panel, and all optional peripheral devices. Review this document before
beginning the installation to determine the hardware and wiring requirements for the features
used.
Throughout this document, the words “control panel ” refer to all control panels covered by
this document (ICP-SOL2-P/ICP-SOL3-P , also known as Solution 2000/3000).
Notifications
This document uses Notices, Cautions, and Warnings to draw your attention to important
information.
Notice!
These include important notes for successful operation and programming of equipment, or
indicate a risk of damage to the equipment or environment.
!
Caution!
These indicate a hazardous situation which, if not avoided, could result in minor or moderate
injury.
!
Warning!
These indicate a hazardous situation which, if not avoided, could result in death or serious
injury.
Copyright
This document is the intellectual property of Bosch Security Systems, Inc. and is protected by
copyright. All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
Related documentation
To obtain any of the documents listed in this section, download them from the web.
Downloading documentation:
1. Go to the Bosch website (us.boschsecurity.com).
2. In the Search text box on the right side of the page, enter the CTN for the product for
which you wish to download the documentation.
3. Press [ENTER].
4. If you see the desired document in the search results, click the link for the document to
open it. Otherwise, click the desired product’s Product Page button. The product page
opens with the Details tab selected.
1
1.1
1.2
8en | Introduction Control Panel
2014.07 | 00n | F01U298026 Installation Guide

5. Click on the Documents tab, and then click the desired language listed to the right of the
desired document.
Call Bosch Security Systems, Inc., Technical Support (1-800-289-0096) if you need additional
assistance.
Control panel documents
Control Panel (ICP-SOL2-P/ICP-SOL3-P) Installation Guide (P/N:F01U298026)
Control Panel (ICP-SOL2-P/ICP-SOL3-P) Quick Reference Guide (P/N:F01U298027)
Control Panel (ICP-SOL2-P/ICP-SOL3-P) User’s Guide (P/N:F01U298028)
*Shipped with the product.
Bosch Security Systems, Inc. product manufacturing dates
Use the serial number located on the product label and refer to the Bosch Security Systems,
Inc. website at http://www.boschsecurity.com/datecodes/.
The following image shows an example of a product label and highlights where to find the
manufacturing date within the serial number.
1.3
Control Panel Introduction | en 9
Installation Guide 2014.07 | 00n | F01U298026

System Overview
ICP-SOL2-P
4
1
2
3
56
7
8
9
10
12
11
13
14 15
16
17
18
Callout - Description
1 – Control panel
2 – Keyfob
3 – WE800EV2 receiver
4 – IUI-SOL adapter
5 – Domestic call
6 – CMS A-Link Plus
7 – PSTN
8 - Receiver
9 – B442 / B450 cellular module
2
2.1
10 en | System Overview Control Panel
2014.07 | 00n | F01U298026 Installation Guide