Bosch Solution 6+6 Wireless On/Off User manual

Solution 6+6 Wireless On/Off
Quick Reference Guide
ISSUE: 1.20

Solution 6+6 Wireless On/Off
Quick Reference Guide
Copyright 1997 by Bosch Security Systems Pty Limited
SYDNEY, AUSTRALIA
Document Part Number MA670Q
Document ISSUE 1.20
Printed 23 May 2006
This documentation is provided to suit the Solution 6+6 Wireless On/Off Control Panel
(CC670/LP670)
Firmware Revision 1.00 - 1.01
Hardware Version A
Alarm Link Form – NFS2V10
Copyright Notice
All rights reserved. No part of this publication may be reproduced, transmitted or stored in a retrieval system in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written
permission of Bosch Security Systems Pty Limited.
Trademarks
Throughout this document trademark names may have been used. Rather than put a trademark symbol in every
occurrence of a trademark name, we state that we are using the names only in an editorial fashion and to the benefit of
the trademark owner with no intention of infringement of the trademark.
Notice of Liability
While every precaution has been taken in the preparation of this document, neither Bosch Security Systems Pty Limited
nor any of its official representatives shall have any liability to any person or entity with respect to any liability, loss or
damage caused or alleged to be caused directly or indirectly by the information contained in this book.
Bosch Security Systems Pty Limited reserves the right to make changes to features and specifications at any time
without prior notification in the interest of ongoing product development and improvement.
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Page 2 Bosch Security Systems Pty Limited

Introduction
Thankyou for choosing the Solution 6+6 Wireless On/Off control panel for your installation. We are sure
that you will find this system extremely flexible, reliable and easy to use.
Before using the system for the first time, we suggest that you read the section in this Quick Reference Guide called
“Programming Using a Codepad” to familiarise yourself with the basic programming methodology.
The Quick Reference Guide is supplied with the control panel to provide users with enough basic information to wire,
configure and operate the system. Due to the systems many programmable features and options, we suggest that you
obtain the complete Installation Manual which provides detailed information on all system options and functions as
well as detailed information on the numerous programming methods.
Programming
The programming options of this system are stored in a non volatile EPROM. This memory will hold all the relevant
configuration and user specific data even during a total power loss.
The data retention time is as long as ten years without power, therefore no reprogramming will be required after
powering the system down.
The data can be altered as many times as required without the need for any additional specialised equipment. This
memory is laid out in numerous locations each of which holds the data for a specific function. In general, the entire
programming sequence will consist of nominating the location number and then entering or altering the required data.
You will repeat this procedure until all the data has been altered to suit your requirements. The factory default settings
have been selected for the control panel to report in Contact ID format.
Note: '15' is the maximum value that can be programmed into any location.
There are two programming modes. The Installer’s Programming Mode and the Operators Programming Mode. Both
modes have individual access codes and these two codes must always be programmed differently. The Master Code, as
well as being able to arm and disarm the system gives access to the Operators Programming Mode. The Installer’s
Code only gives access to the Installer’s Programming Mode and does NOT arm and disarm the system.
Programming of the Solution 6+6 Wireless On/Off control panel can be carried out via any of the
following four methods.
System Codepad
Hand Held Programmer (CC814)
Programming Key (CC810)
Alarm Link (Upload/Download) Software (CC816)
Note: For further information on the different programming options available for the Solution 6+6
Wireless On/Off control panel, refer to the Installation Manual (MA670I).
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Electronics Design & Manufacturing Pty Limited Page 3

Programming Using a Codepad
The system must be in a disarmed state with no flashing zone alarm memories, this can be achieved by entering the
followed by the button. The factory default Master Code is 2580.
To access the Installer’s Programming Mode, enter the four digit followed by the button. The
factory default Installer Code is 1234. Three beeps will be heard and both the AWAY and the STAY indicators
will flash simultaneously. If a long beep is heard, check the system for alarm memory. The combination of the MAINS
and ZONEindicators will indicate the data stored in the first location (LOCATION 000).
Exam ple
To move to a particular programming location, enter the location number required followed by the button.
The data of the new location will now be displayed.
To move to the next location, press the button. This will step you to the next location and the data in that
location will be displayed via the zone LED indicators.
If you press the button without previously entering a location number, the system will step back one location.
To change data in the current location, enter the new value followed by the button. This will store the new
data into the location and still leave you still positioned at the same location.
To proceed to the next location, press the button. The next locations data will now be displayed.
To exit the Installer’s Programming Mode, enter the command 960 followed by the button. Two beeps
will be heard and the system will return to normal.
For a more detailed explanation, refer to the Solution 6+6 Wireless On/Off
Installation Manual (MA670I)
Note: The valid address range for a Solution 6+6 Wireless On/Off control panel is 000 to 213.
Data
Value Zone 1 LED Zone 2 LED Zone 3 LED Zone 4 LED Zone 5 LED Zone 6 LED Zone 7 LED Zone 8 LED Mains LED
1 
2 
3 
4 
5 
6 
7 
8 
9  
10 
11  
12  
13  
14  
15  
Zone Indicators When Programming
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Page 4 Bosch Security Systems Pty Limited

Quick Start
The following steps will enable you to use the Solution 6+6 Wireless On/Off control panel with the
default values as set in the factory. The default settings allow the panel to communicate in Contact ID format.
1. Connect AC power to the unit.
The MAINS indicator will remain on as will the AWAY indicator. The unit is now in the armed state.
2. The back-up battery should now be connected.
3. Enter the default Master Code 2580 followed by the button. The AWAY indicator will
extinguish. The panel is now in the disarmed state. Installer’s Programming Mode can now be accessed.
4. Enter the factory default Installer Code 1234 followed by the button. The STAY and AWAY
LED’s will now flash simultaneously.
5. Enter the primary and secondary telephone numbers and the Subscriber ID Number.
6. Set the time for the test reports if this option is required. Any other programming changes required can also be
made, otherwise the factory programming default settings will be used.
7. Enter command 960 followed by the button to exit Installer’s Programming Mode. The panel will
return to the unarmed state and is now ready for use.
8. Using a Master Code set the date and time.
• Enter + 6+ .
• Enter the day of the month, then the month, then the year, then the hour, then the minute using the format
(DD, MM, YY, HH, MM).
• Press the button when finished.
Zone DefaultSettings
The default zone settings are as listed in the table below.
Zone No. Zone Type
1 Delay
2 & 3 Handover
4 & 5 Instant
6 24 Hour
Note: The example given in this Quick Reference Guide is a simplified description of how to configure the
panel. The system offers many other programmable features which are described in detail in the
Solution 6+6 Wireless On/Off Installation Manual (MA670I).
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Electronics Design & Manufacturing Pty Limited Page 5

Installer’sProgram m ing Commands
There are several commands that can be invoked to perform the functions as listed below. These commands only
operate while you are in the Installers Programming Mode. To invoke the command, press in the corresponding
numerical code then press the button.
Com m and Function
958 Enable and Disable Zone Status Mode
959 Test Programming Key
960 Exit Installer’s Programming Mode
961 Set Defaults For Contact ID Format (Factory Default Settings)
962 Copy The Panel Memory To The Programming Key
963 Copy The Programming Key Data To The Panel Memory
964 Wipe Programming Key
965 Set Defaults For Domestic Reporting
966 Enable and Disable Automatic Stepping of Locations During Programming
999 This Command Displays The Solution Panel’s “Software Version” Number When
Using An BOSCH Hand Held Programmer
Installers Programming Commands
InstallerCode Functions
Installer Code Functions are designed to allow the installer to perform various system tests without the need to know a
Master Code.
The is entered followed by a digit then the button to enter you into a particular
mode. If a button is not pressed within any sixty second period, the mode will automatically terminate.
++
These functions can only be carried out while the system is in a disarmed state.
Function Description
0 Fault Analysis Mode
1 Reserved
2 Set Number Of Days Until The First Test Report
3 Event Memory Recall
4 Walk Test Mode
5 Satellite Siren (BOSCHSAT) Service Mode
6 Initiate Modem Call
7 Turning Telephone Monitor Mode On and Off
8 Reserved
9 Send A Test Report
Installer Code Functions
MasterCode Functions
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Page 6 Bosch Security Systems Pty Limited

Master Code Functions are designed to allow those users that have the appropriate access level to perform certain
functions of a supervisory level. These functions can only be carried out while the system is in a disarmed state.
++
Function Description
0 Arming and Disarming Both Areas At The Same Time
1 Changing and Deleting User Codes/Radio Remote User Codes
2 Changing Phone Numbers (Domestic Only)
3 Event Memory Recall
4 Walk Test Mode
5 Fault Analysis
6 Setting The Date and Time
7 Toggle Day Alarm On and Off
8 Reset Latched Outputs
9 Initiate Modem Call
Master Code Functions
FaultAnalysis
There are various system faults that can be detected by the Solution 6+6 Wireless On/Off control panel.
When any of these are present the FAULT indicator will begin to flash and the codepad will beep once every minute.
Hold the 5button down for two seconds until two beeps are heard. The STAY and AWAY indicators will begin to
flash in unison with the FAULT indicator. One or more zone indicators (1-8) will illuminate to indicate the current
fault. Refer to the following table for a list of fault types.
Zone Indicator Description
1 Low Battery
2 Date and Time
3 Sensor Watch
4 Horn Speaker Disconnected
5 Reserved
6 E2Fault
7 Reserved
8 Communications Failure
Fault Types
UserCode Functions
++
Function Description
0 Arming and Disarming Both Areas At The Same Time
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Electronics Design & Manufacturing Pty Limited Page 7

Hold DownFunctions
Hold Down Functions have been incorporated to allow easy activation of specific operations. When a button is held
down for two seconds, two beeps will be heard and a particular function will operate. These functions are listed below.
Testing The Dialler
Telephone monitor mode allows the remote codepad to be used for a visual representation of data transmissions
between the control panel and the base station receiver. The dialling sequence is also shown in this mode.
The codepad will beep once every two seconds while telephone monitor mode is turned on regardless of whether the
system is in Installer's Programming Mode or normal operating mode. The first five indicators are used to display the
progressive steps for a transmission to the base station receiver.
Zone Indicator Dialling Event
1 Telephone Line Seized
2 Dialling Phone Number
3 Handshake Received
4 Data Is Being Transmitted
5 Kiss-Off Received
None Telephone Line Released
Telephone Monitor Mode Indications
How To Turn Telephone MonitorM ode Onand TestThe Dialler
1. Enter your followed by 7and the button.
Three beeps will be heard.
2. Hold Down button 9for two seconds until two beeps are heard to initiate a test report.
How To Turn Telephone MonitorM ode Off
1. Enter your followed by 7and the button.
Two beeps will be heard.
Each zone contains five locations. The first four locations determine how the zone operates, while the last location
contains the dialler reporting information.
Function Description
AWAY Arm The System in AWAY Mode
STAY Arm The System in STAY Mode
0 Reserved
1 Horn Speaker Test
2 Bell Test
3 Strobe Test
4 Toggle Day Alarm On and Off
5 Fault Analysis
6 Initiate a Modem Call
7 Reset Latching Outputs
8 Codepad ID Beeper Tone Change
9 Initiate a Test Report
Hold Down Functions
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Page 8 Bosch Security Systems Pty Limited

0 0 0 0 0
Type Option Pulse Time Dialler
Zone Types
There are fifteen different zone types to choose from. Each has the ability to be programmed as any of the types listed
in the table below.
Type Description Type Description
0 Instant 8 Delay 1 + Isolated In STAY Mode
1 Handover 9 Delay 2 + Isolated In STAY Mode
2 Delay 1 10 Reserved
3 Delay 2 11 Keyswitch
4 Reserved 12 24 Hour
5 Reserved 13 24 Hour Fire
6 Instant + Isolated In STAY Mode 14 Chime Only (follow me)
7 Handover + Isolated In STAY Mode 15 Zone Not Used
Zone Options
Keyswitch Zone Options
Pulse CountSettings
The pulse count settings for each zone can be programmed between 0 - 15.
Pulse CountTime
Zone time is the time frame or period over which the number of pulses must register.
Zone Descriptions
Zone Description Tam perZonesDescription
1
2
3
4
5
6
Option Description
1 Lockout Siren
2 Lockout Dialler
4 Silent Alarm
8 Sensor Watch
Option Description
1 Arm Only
2 Disarm Only
4 Enabled = Arm In STAY mode
Disabled = Arm In AWAY mode
8 Enabled = Momentary operation
Disabled = Toggle operation
20m sLoop Response Time 150m sLoop Response Time
0 0.5 Seconds 8 20 Seconds
1 1 Second 9 30 Seconds
2 2 Seconds 10 40 Seconds
3 3 Seconds 11 50 Seconds
4 4 Seconds 12 60 Seconds
5 5 Seconds 13 90 Seconds
6 10 Seconds 14 120 Seconds
7 15 Seconds 15 200 Seconds
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Electronics Design & Manufacturing Pty Limited Page 9

Location 00 - 15
Primary Telephone Number
Location 16 - 31
Secondary Telephone Number
Location 32 - 47
Callback Telephone Num ber
Location 48
Dialling Format
Location 49
Handshake Tone
Location 50
Transmission Format
Location 51
Reserved
Location 52 - 55
SubscriberID Number
Location 56 - 59
InstallerCode
Location 60 15 = Answering Machine Bypass 1
Ring Count 14 = Answering Machine Bypass 2
Location 61 - 100
UserCodes
Location 101
DayAlarm Mask
Location 102
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1
1 = Australian DTMF 4 = International DTMF
2 = Australian Decadic 5 = Reversed Decadic
3 = Alternate DTMF & Decadic (Aus.) 6 = Alternate DTMF & Reverse Decadic
1
1 = Hi-Lo Handshake (Contact ID) 4 = No Handshake Required
2 = 1400 Hz(Ademco TX @ 1900 Hz) 5 = Pager
3 = 2300 Hz (Sescoa TX @ 1800 Hz)
1 = Contact ID 6 = Reserved 11 = Domestic
2 = Reserved 7 = Reserved 12 = Basic Pager
3 = Reserved 8 = Reserved 13 = Reserved
4 = Reserved 9 = Reserved 14 = Reserved
5 = Reserved 10 = Reserved 15 = Reserved 1
0
0 0 0 0
1 2 3 4
8
UserCode #1 Location 61 - 65 UserCode #2
Location 66 - 70
2 5 8 0 8 15 15 15 15 0
UserCode #3 Location 71 - 75 UserCode #4 Location 76 - 80 UserCode #5
Location 81 - 85
15 15 15 15 0 15 15 15 15 0 15 15 15 15 0
UserCode #6
Location 86 - 90 UserCode #7 Location 91 - 95 UserCode #8
Location 96 - 100
15
15 15 15
0
15
15 15 15
0
0
15 15 15
1
1
1 = Zone 1
2 = Zone 2
4 = Zone 3
8 = Zone 4
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Page 10 Bosch Security Systems Pty Limited

Code Retries
Location 103
EOL ResistorValue
Location 104 - 133
Zones
Zone #1
Location 104 - 108 Zone #3 Location 114 - 118 Zone #5
Location 124 - 128
2
0 0 0 3 1 0 0 0 3 0 0 0 0 3
Zone #2
Location 109 - 113 Zone #4 Location 119 - 123 Zone #6 Location 129 - 133
1
0 0 0 3 0 0 0 0 3 12 0 0 0 3
ReportOption
1 = Enable Alarm Report 4 = Reserved
2 = Enable Restore Report 8 = Reserved
Location 134
ReportOptions1
Location 135
ReportOptions2
Location 136
ReportOptions3
Location 137 - 139
TestReporting Time(RepeatDays,HoursTens,HoursUnits)
Location 140 - 163
OutputConfigurations
Location 140- 145 Location 146 - 151
Output#1 1
14 0 0 0 0
Strobe 2
0 1 0 0 0
Location 152 - 157 Location 158 - 163
Relay 1
15 1 0 0 0
Console0
12 2 1 0 1
Event Type
(when) Polarity (how) Time (base) Time (multiplier)
Location 164 - 165
Entry Timer1 (Seconds,16 Seconds)
Location 166 - 167
Entry Timer2 (Seconds,16 Seconds)
Location 168 - 169
ExitTimer(Seconds,16 Seconds)
6
1 = 1K
Ω
5 = 3K9
Ω
9 = 10K
Ω
13 = Reserved
2 = 1K5
Ω 6 = 4K7 Ω 10 = 12K Ω 14 = Reserved
3 = 2K2
Ω 7 = 5K6 Ω 11 = 22K Ω 15 = Split EOL For 6 Tampers
4 = 3K3
Ω 8 = 6K8 Ω 12 = Reserved 4
Type Option Pulse Time Report
Option
1 = Enable Bypass Reports
2 = Enable Bypass Restore Reports
4 = Enable Trouble Reports
8 = Enable Trouble Restore Reports 15
1 = Enable Duress Reports
2 = Enable Panic, Medical and Fire Reports
4 = Enable Access Denied Reports
8 = Enable Test Reports 15
1 = Enable AC Fail Report
2 = Enable Low Battery Reports
4 = Enable Sensor Watch Reports
8 = Enable Opening/Closing Reports 15
0 0 0
10 0
4 1
12 3
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Electronics Design & Manufacturing Pty Limited Page 11

Location 170 - 171
Entry Guard Timer(Seconds,16 Seconds)
Location 172 - 173
SensorWatch Time(Days)
Location 174
Codepad LockoutTime(10 Second)
Location 175
Siren RunTime(Minutes)
Location 176
Siren Sound Rate (Slow <-Sound-> Fast)
Location 177
SwingerShutdown Count
Location 178
DiallerOptions1
Location 179
DiallerOptions2
Location 180
System Options1
Location 181
System Options2
Location 182
System Options3
Location 183
System Options4
Location 184
Consum erOptions1
Location 185
Consum erOptions2
Location 186 - 191
Area 1 Zone Allocations
12 3
0 0
0
10
7
0
5
1 = Enable Dialler Reporting Functions
2 = Enable Remote Arming Via The Telephone
4 = Enable Upload/Download Via BOSCH Alarm Link Software (CC816)
8 = Terminate “Alarm Link” Session On Alarm
0
1 = Send Open/Close Reports Only If A Previous Alarm Has Occurred
2 = Enable First To Open, Last To Close Reporting (Partitioning Only)
4 = Send Open/Close Reports When In STAY Mode
8 = Delay Siren Until Transmission Is Complete
1
1 = Enable Forced Arming
2 = Enable BOSCH Smart Lockout
4 = Enable Monitoring Of Horn Speaker
8 = Allow Horn Speaker Beeps For Radio Remote Control Operation
2
1 = Enable BOSCH Radio Key/Keyswitch Interface or BOSCH Night Arm Station
2 = Enable Handover Delay To Be Sequential
4 = Enable Codepad Panic To Be Silent
8 = Enable Access Denied To Be Silent
0
1 = Enable Main Codepad To Display Data For Area #1
2 = Enable Resetting Of Sirens From Both Areas
4 = Ignore AC Fail
8 = Enable Handover Of Zone Pulse Count
1 = Enable AC Fail In 1 hour
2 = Extend Time To Wait For Handshake From 30 Seconds To 1 Minute
4 = Enable Control Panel To Power Up In The Disarmed State
8 = Reserved 0
2
1 = Send Test Reports Only When The System Is Armed
2 = Enable Operation Of Siren & Strobe In STAY Mode
4 = Enable Answering Machine Bypass To Work Only When The System Is Armed
8 = Enable Codepad Extinguish Mode
0
1 = Enable “User Code + 0 + AWAY” Function To Arm/Disarm BOTH Areas At Same Time
2 = Enable Single Button Arming in Away and Stay mode
4 = Enable Single Button Disarming from Stay mode
8 = Enable Alarm Memory Reset on disarm
0 0 0 0 0 0
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Page 12 Bosch Security Systems Pty Limited

Location 192 - 197
Area 2 Zone Allocations
Location 198 - 205
Area/UserAllocations
Location 198 Location 199 Location 200 Location 201
AreasforUser#
1
0
AreasforUser#
2
0
AreasforUser#
3
0
AreasforUser#
4
0
Location 202 Location 203 Location 204 Location 205
AreasforUser#
5
0
AreasforUser#
6
0
AreasforUser# 7
0
AreasforUser#
8
0
Location 206 - 213
Radio UserAllocations
Location 206 Location 207 Location 208 Location 209
Ra
d
io User#
9
0
Ra
d
io User# 1
0
0
Ra
d
io User# 1
1
0
Ra
d
io User# 1
2
0
Location 210 Location 211 Location 212 Location 213
Ra
d
io User# 1
3
0
Ra
d
io User# 1
4
0
Ra
d
io User# 1
5
0
Ra
d
io User# 1
6
0
Location 900
Disable Factory Default
0
0 0 0 0 0
0 = Defaulting Enabled
15 = Defaulting Disabled 0
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Electronics Design & Manufacturing Pty Limited Page 13

Wiring Diagram
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Page 14 Bosch Security Systems Pty Limited

Com ponentOverlay
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Electronics Design & Manufacturing Pty Limited Page 15

WirelessON/OFFInterface
Wiring Diagram sforKeyswitch Zones
Figure 1: Wiring Diagram for Keyswitch Zone
Figure 2: Wiring Diagram for Keyswitch Zone in Partitioning
Note 1: When choosing an EOL resistor value other than the default 3K3 for a non-partitioned system, the
keyswitch zone must still use a 3K3 EOL resistor as shown in “Figure 1”. The keyswitch zone will not
operate with any other resistor value.
Note 2: When using a keyswitch zone in partitioning, to enable arming/disarming of area 2, there is no need to
enable split EOL resistors when not using tamper zones. Simply wire the zone as shown in “Figure 2”.
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Page 16 Bosch Security Systems Pty Limited

ConnectionsOfSplitEOLResistorsForTam perOperation
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Electronics Design & Manufacturing Pty Limited Page 17

Codepad ConnectionsForPartitioned System s
If the “Area Addressable” codepad is assigned to Area 1, DIP Switch 1 on the back of the remote codepad will need to
be in the “ON” position. The following locations for Output 1 will need to be programmed.
[LOCATION 140 = 6, 141 = 0]
If the “Area Addressable” codepad is assigned to Area 2, DIP Switch 2 on the back of the remote codepad will need to
be in the “ON” position. The following locations for Output 1 will need to be programmed.
[LOCATION 140 = 6, 141 = 1]

The following DIP Switch settings and locations must be programmed for the two “Area Addressable” codepads to
function correctly.
AREA 1 CODEPAD
DIP Switch 1 on the back of the remote codepad will need to be in the “ON” position. The following location will also
need to be programmed.
[LOCATION 182, Option Bit 1 must be enabled]
AREA 2 CODEPAD - (Output 1)
DIP Switch 2 on the back of the remote codepad will need to be in the “ON” position. The following location will also
need to be programmed.
[LOCATION 140 = 6, 141 = 1]
Solution 6+6 Wireless On/Off Quick Reference Guide ISSUE 1.20
Electronics Design & Manufacturing Pty Limited Page 19