Bosch Solution-16 safecom User manual

Solution-16/
Solution-16 Safecom
Quick Reference Guide
ISSUE 2.41

Solution-16/
Solution-16 Safecom
Quick Reference Guide
Copyright 2001 by Bosch Security Systems Pty Limited,
SYDNEY, AUSTRALIA
Document Part Number MA880Q
Document ISSUE 2.41
This documentation is provided to suit both the
Solution-16 (CC880/LP880) and Solution-16 Safecom (SC8016)
Firmware Revision 2.06
Hardware Revision K
Alarm Link Forms
Software Version 1.10 = S16_V11 Software Version 1.40 = S16_V4
Software Version 1.20 = S16_V12 Software Version 2.0x = S16_V20
Software Version 1.3x = S16_V13
This quick reference guide includes programming locations to suit both Solution-16 (CC880/LP880) and the
Solution-16 Safecom (SC8016) control panel. Locations that are only relevant when using the SC8016 are
prefixed with the word Safecom.
Copyright Notice
All rights reserved. No part of this publication may be reproduced, transmitted or stored in a retrieval system in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Bosch Security Systems Pty Limited.
Trademarks
Throughout this document trademark names may have been used. Rather than put a trademark symbol in every
occurrence of a trademark name, we state that we are using the names only in an editorial fashion and to the
benefit of the trademark owner with no intention of infringement of the trademark.
Notice of Liability
While every precaution has been taken in the preparation of this document, neither Bosch Security Systems Pty
Limited nor any of its official representatives shall have any liability to any person or entity with respect to any
liability, loss or damage caused or alleged to be caused directly or indirectly by the information contained in this
book.
Bosch Security Systems Pty Limited reserves the right to make changes to features and specifications at any
time without prior notification in the interest of ongoing product development and improvement.
2 Solution-16/Solution-16 Safecom Quick Reference Guide
SOL 16 SAFECOM QUICK REF GUIDE.DOC.DOC Bosch Security Systems Pty Limited

Introduction
Thank you for choosing the Solution control panel for your installation. We are sure that you will
find this system extremely flexible, reliable and easy to use. The quick reference guide is supplied
with the system to provide users with enough basic information to wire, configure and program the
system. Due to the systems many programmable features and options, we suggest that you obtain
the complete installation manual that provides detailed information on system options and functions
and programming methods.
Programming
The programming options of the system are stored in a non-volatile EPROM. This memory will
hold all information during a total power loss and can be changed as many times as required.
In general, the entire programming sequence will consist of entering a location number and then
change the data as required.
Programming the system can be via the following methods:
• Codepad
• Hand Held Programmer
• Alarm Link Software
Programming Using A Codepad
The system needs to be disarmed (with no active alarm) to program the control panel. If there is
an active alarm or the system is armed, enter the code for User 1 (Default = 2580) followed by the
# key (User Code 1 is factory default as the Master Code).
To enter installer’s programming mode, enter the installer code (Default = 1234) followed by the #
key. Two beeps will be heard. Both the STAY and AWAY indicators will flash simultaneously to
indicate that you have entered programming mode. The codepad indicators will display the current
data programmed in LOCATION 000 (First location of the Primary Telephone Number).
To move to another programming location, enter the location number followed by the # key. The
data in the new location will now be displayed via the codepad indicators (Eg. If you entered 52#,
the system will jump you to LOCATION 052 the beginning of the Subscriber ID Number For Area
1).
To move to the next location, press the # key. This will step you to the next location. The data in
the next location will now be displayed via the codepad indicators (Eg. If you are currently
positioned at LOCATION 052, pressing the # key will take you to LOCATION 053).
To step back one location, press the * key (Eg. If you are currently positioned at LOCATION 53,
pressing the * key will take you back to LOCATION 52).
To change data in the current location, enter the new value (0 – 15) followed by the * key. This will
store the new data into the location and leave you at the same location (Eg. If you enter the value
14*, both the Zone 4 indicator and the MAINS indicator will display to represent the new data
value).
To move to the next location, press the # key. The data in the next location will now be displayed.
To exit Installer’s Programming Mode, enter 960#. Two beeps will be heard and the STAY and
AWAY indicators will no longer display. The system has now returned to the disarmed state and is
now ready for use.
The table below is a quick guide to programming:
Enter Installer’s Programming Mode 1234#
Exit Installer’s Programming Mode 960#
Step To Next Location #
Step Back One Location *
Program New Data Into Location Data + * (Data = 0 – 15)
Jump To A New Location Location Number + #
Solution-16/Solution-16 Safecom Quick Reference Guide 3
Bosch Security Systems Pty Limited

Codepad Indicators
Data
Value Zone 1 Indicator Zone 2 Indicator Zone 3 Indicator Zone 4 Indicator Zone 5 Indicator Zone 6 Indicator Zone 7 Indicator Zone 8 Indicator MAINS Indicator
0
1 X
2 X
3 X
4 X
5 X
6 X
7 X
8 X
9 X X
10 X
11 X X
12 X X
13 X X
14 X X
15 X X
Programming Option Bits
You will notice option bits throughout the quick reference guide. This allows you to program any
combination of the four different options in the one location by adding the options together.
Programming a zero (0) will disable all four options.
Example If at LOCATION 663 you only want options 1, 2 and 4, add the numbers together and the total is
the number to be programmed. In this example, the number to be programmed is 7 (Eg. 1 + 2 + 4
= 7).
Option Description
1 Dialler Reporting Functions Allowed
2 Remote Arming Via Telephone Allowed
4 Upload/Download Via Alarm Link Allowed
8 Terminate Alarm Link Session On Alarm
Installer’s Programming Commands
These commands can only be used when you enter Installer’s Programming Mode. Enter the
command followed by the # key.
Command Description
958 Enable/Disable Zone Status (Hand Held Programmer Required)
959 Test Programming Key
960 Exit Installer’s Programming Mode
961 Default System Back To Factory Settings
962 Copy Panel Memory To Programming Key
963 Copy Programming Key To Panel Memory
964 Erase Programming Key
965 Default System For Domestic Dialling Format
966 Enable/Disable Automatic Stepping Of Locations When Programming
999 Display Software Version (Hand Held Programmer Required)
4 Solution-16/Solution-16 Safecom Quick Reference Guide
SOL 16 SAFECOM QUICK REF GUIDE.DOC.DOC Bosch Security Systems Pty Limited

Arming The System (On)
AWAY Mode
1. Press and hold the # key until two beeps are
heard.
Or
2. Enter your code followed by the # key.
[eg. 2580 + #].
STAY Mode 1
1. Press and hold the * key until two beeps are
heard.
Or
2. Enter your code followed by the * key.
[eg. 2580 + *].
STAY Mode 2
1. Press and hold the 0 key until two beeps are
heard.
Arm All Areas In AWAY Mode (Partitioning)
1. Enter your code followed by 0 and then the #
key [eg. 2580 + 0 + #].
This function allows a code to arm all areas that the
code is assigned to in AWAY Mode at the same time
without the need to arm each area individually.
Disarming The System (Off)
AWAY Mode
1. Enter your code followed by the # key.
[eg. 2580 + #].
STAY Mode 1
1. Press and hold the * key until two beeps are
heard (Only if no alarm).
Or
2. Enter your code followed by the # key.
[eg. 2580 + #].
STAY Mode 2
1. Press and hold the 0 key until two beeps are
heard (Only if no alarm).
Or
2. Enter your code followed by the # key.
[eg. 2580 + #].
Disarm All Areas (Partitioning)
1. Enter your code followed by 0 and then the #
key [eg. 2580 + 0 + #].
This function allows a code to disarm all areas that
the code is assigned to at the same time without the
need to disarm each area individually.
Isolating Zones
Standard Isolating
1. Press the * key twice.
2. Enter the zone number that you want to
isolate followed by the * key.
Repeat step 2 if more than one zone is
required to be isolated.
3. Press the # key to exit when finished.
Code To Isolate
1. Press the * key once.
2. Enter your user code.
3. Enter the zone number that you want to
isolate followed by the * key.
4. Repeat step 2 if more than one zone is
required to be isolated.
5. Press the # key to exit when finished.
Solution-16/Solution-16 Safecom Quick Reference Guide 5
Bosch Security Systems Pty Limited

Set First Test Report
1. Enter the Installer Code followed by 2 and the
key [eg. 1234 + 2 + #].
2. Enter the Number Of Days (0 - 99) to wait
until first test report followed by the # key.
Event Memory Recall
1. Enter the Installer Code or Master Code
followed by 3 and the # key.
[eg. 1234 + 3 + #].
The last 40 events (non partitioned) or last 10 events
(partitioned) will be displayed in reverse order (i.e.
most recent to least recent).
Walk Test Mode
1. Enter the Installer Code or Master Code
followed by 4 and the # key.
[eg. 1234 + 4 + #].
2. Test each zone as required.
3. Press the # key to exit.
Satellite Siren Service Mode
1. Enter the Installer Code followed by 5 and the
# key [eg. 1234 + 5 + #].
Telephone Monitor Mode (Toggle On/Off)
1. Enter the Installer Code followed by 7 and the
# key [eg. 1234 + 7 + #].
2. Press and hold the 9 key until two beeps are
heard to send a test report.
3. Repeat Step 1 to turn telephone monitor
mode off when complete.
Zone LED Dialling Event
1 Telephone Line Seized
2 Dialling Telephone Number
3 Handshake Received
4 Data Being Sent
5 Kiss-Off Received
None Released Telephone Line
Add A User Code
1. Enter the Master Code followed by 1 and the
# key [eg. 2580 + 1 + #].
2. Enter the User Number that you want to
add/change followed by the # key.
3. Enter the New Code followed by the # key.
Delete A User Code (V1.10)
1. Enter the Master Code followed by 1 and the
# key [eg. 2580 + 1 + #].
2. Enter the User Number that you want to
delete followed by the # key.
3. Press the # key again to delete the user code.
Delete A User Code (V1.20+)
1. Enter the Master Code followed by 1 and the
# key [eg. 2580 + 1 + #].
2. Enter the User Number that you want to
delete followed by the # key.
3. Press the * key to delete the user code.
Change Domestic Telephone Numbers
1. Enter the Master Code followed by 2 and the
# key [eg. 2580 + 2 + #].
2. Enter the digits for the telephone number.
3. If more than one telephone number, press the
* key and repeat Step 2, else press the # key
to exit.
Turn Outputs On/Off
1. Enter the Master Code followed by 5 and the
# key [eg. 2580 + 5 + #].
2. Enter the Output Number (1 – 5) that you
want to toggle on or off.
3. Press the # key to toggle On or the * key to
toggle Off.
4. Press the # key to exit.
Setting Date and Time
1. Enter the Master Code followed by 6 and the
# key [eg. 2580 + 6 + #].
2. Enter the day (DD), month (MM) and year
(YY) followed by the hour (HH) and minute
(MM).
3. Press the # key to exit.
6 Solution-16/Solution-16 Safecom Quick Reference Guide
SOL 16 SAFECOM QUICK REF GUIDE.DOC.DOC Bosch Security Systems Pty Limited

Day Alarm – Toggle On/Off (V1.10)
1. Enter the Master Code followed by 7 and the
# key [eg. 2580 + 7 + #].
Day Alarm – Toggle On/Off (V1.20+)
1. Press and hold the 4 key until two beeps are
heard.
STAY Mode 2 Zones - Program
1. Enter the Master Code followed by 8 and the
# key [eg. 2580 + 8 + #].
2. Enter the Zone Number that you want the
system to automatically isolate followed by the
* key.
3. Repeat if more than one zone to be
automatically isolated when armed in STAY
Mode 2.
4. Press the # key to terminate.
Fault Analysis
1. Press and hold the 5 key until two beeps are
heard.
2. Zone Indicators will display FAULT condition
(see table below).
3. Press # key to terminate.
Zone LED FAULT Condition
1 Battery Low
2 Date / Time Reset
3 Sensor Watch Fail
4 Horn Speaker Fail
5 Telephone Line Fail
6 EPROM Fail
7 Zone 16 In Alarm (Partitioning)
8 Communication Fail
Modem Call (Alarm Link)
1. Press and hold the 6 key until two beeps are
heard.
Latching Outputs (Reset)
1. Press and hold the 7 key until two beeps are
heard.
Codepad ID / Buzzer Tone
1. Press and hold the 8 key until the desired
buzzer tone has been reached.
If the system has been partitioned, the
codepad will display a number to identify
which area the codepad belongs to (see table
below).
2. Press the # key to terminate.
Zone LED Codepad Assignment
1 Area 1
2 Area 2
3 Area 3
4 Area 4
7 Master Partitioned Codepad
Test Report
1. Press and hold the 9 key until two beeps are
heard.
Speaker Test
1. Press and hold the 1 key until two beeps are
heard. The horn speaker will sound for two
seconds.
Bell Test
1. Press and hold the 2 key until two beeps are
heard. The piezo will sound for two seconds.
Strobe Test (Toggle On/Off)
1. Press and hold the 3 key until three beeps are
heard to turn the strobe on.
2. Press and hold the 3 key until two beeps are
heard to turn the strobe off.
Solution-16/Solution-16 Safecom Quick Reference Guide 7
Bosch Security Systems Pty Limited

Location 000 – 015
Primary Telephone Number
(0=10 and telephone termination = 0, anywhere else 0=0)
Location 016 – 031
Secondary Telephone Number
(0=10 and telephone termination = 0, anywhere else 0=0)
Location 032 – 047
Call Back Telephone Number
(0=10 and telephone termination = 0, anywhere else 0=0)
Location 48
Dialling Format
Location 49
Handshake Tone
Location 50
Transmission Format
Location 51
Transmission Speed
Location 052 – 055
Subscriber ID Number For Area 1
Location 056 – 062
Installer Code
Location 063
Ring Count
Location 064 – 319
User Codes
User Code 1 Authority
Level User Code 2 Authority Level User Code 3 Authority Level
Location 064 - 070 071 Location 072 - 078 79 Location 080 - 086 87
2 5 8 0 15 15 15 8 15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0
User Code 4 Authority
Level User Code 5 Authority Level User Code 6 Authority Level
Location 088 - 094 095 Location 096 - 102 103 Location 104 - 110 111
15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0
User Code 7 Authority
Level User Code 8 Authority Level User Code 9 Authority Level
Location 112 - 118 119 Location 120 - 126 127 Location 128 - 134 135
15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0
User Code 10 Authority
Level User Code 11 Authority Level User Code 12 Authority Level
Location 136 - 142 143 Location 144 - 150 151 Location 152 - 158 159
15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0
User Code 13 Authority Level User Code 14 Authority Level User Code 15 Authority Level
Location 160 - 166 167 Location 168 - 174 175 Location 176 - 182 183
0 0 0 0 0 0 0 0 15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0
0000000000000000
0000000000000000
0000000000000000
1 = Australian DTMF 4 = International DTMF
2 = Australian Decadic 5 = Reversed Decadic
3 = Alternate DTMF & Decadic (Aust) 6 = Alternate DTMF & Reversed Decadic 1
1 = HI-LO Handshake (Contact ID) 4 = No Handshake
2 = 1400 Hz (Ademco TX @ 1900 Hz) 5 = Pager
3 = 2300 Hz (Sescoa TX @ 1800 Hz) 1
1 = Contact ID 6 = 4 + 1 Pulsed Expanded 11 = Domestic
2 = 4 + 2 Expressed 7 = 3 + 1 Pulsed Universal 12 = Basic Pager
3 = 4 + 2 Pulsed 8 = 3 + 1 Pulsed Expanded 13 = Reserved
4 = 4 + 2 Pulsed + Checksum 9 = Reserved 14 = PET Alpha Pager
5 = 4 + 1 Pulsed + Universal 10 = Reserved 15 = Synthesised Voice 1
1 = 1 Pulse / Second 4 = 20 Pulses / Second
2 = 10 Pulses / Second 5 = 20 Pulses / Second FDL
3 = 15 Pulses / Second 6 = 40 Pulses / Second 2
0 0 0 0
1 2 3 4 15 15 15
0 = Panel Will Not Answer 14 = Answering Machine Bypass 2 (V1.37+)
1 – 13 = No Of Rings Until Panel Answers 15 = Answering Machine Bypass 1 8
8 Solution-16/Solution-16 Safecom Quick Reference Guide
SOL 16 SAFECOM QUICK REF GUIDE.DOC.DOC Bosch Security Systems Pty Limited

User Code 16 Authority Level User Code 17 Authority Level User Code 18 Authority Level
Location 184 - 190 191 Location 192 - 198 199 Location 200 - 206 207
15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0
User Code 19 Authority
Level User Code 20 Authority Level User Code 21 Authority Level
Location 208 - 214 215 Location 216 - 222 223 Location 224 - 230 231
15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0
User Code 22 Authority Level User Code 23 Authority Level User Code 24 Authority Level
Location 232 - 238 239 Location 240 - 246 247 Location 248 - 254 255
15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0
User Code 25 Authority Level User Code 26 Authority Level User Code 27 Authority Level
Location 256 - 262 263 Location 264 - 270 271 Location 272 - 278 279
0 0 0 0 0 0 0 0 15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0
User Code 28 Authority Level User Code 29 Authority Level User Code 30 Authority Level
Location 280 - 286 287 Location 288 - 294 295 Location 296 - 302 303
15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0 15 15 15 15 15 15 15 0
User Code 31 Authority
Level User Code 32 Authority Level
Location 304 - 310 311 Location 312 - 318 319
15 15 15 15 15 15 15 0 0 15 15 15 15 15 15 1
Authority Levels
Authority
Level Description
0 Arm/Disarm
1 Arm Only
2 Patrolman Code
4 Arm/Disarm + Code Required To Isolate
6 Patrolman Code + Code Required To Isolate
8 Master Code + Arm/Disarm
12 Master Code + Arm/Disarm + Code Required To Isolate
Location 320 - 335
Auxiliary Codes
Authority
Level Description
1 Operate When The System Is Armed
2 Operate When The System Is Disarmed
3 Operate When The System Is Armed Or Disarmed
4 Operate Always As Long As No Alarm memories Are Present
5 Operate If Armed & No Alarm Memories Are Present
6 Operate If Disarmed & No Alarm Memories Are Present
7 Operate If Armed Or Disarmed & No Alarm Memories Are Present
Location 336 - 337
Day Alarm Zones
Auxiliary Code 1 Authority Level Auxiliary Code 2 Authority Level
Location 320 - 326 327 Location 328 - 334 335
15 15 15 15 15 15 15 2 15 15 15 15 15 15 15 2
1 = Zone 1 1 = Zone 5
2 = Zone 2 2 = Zone 6
Location 336 4 = Zone 3 Location 337 4 = Zone 7
8 = Zone 4 8 = Zone 8 1 0
Solution-16/Solution-16 Safecom Quick Reference Guide 9
Bosch Security Systems Pty Limited

Location 338
User Code Retries
Location 339
EOL Resistor Value
Location 340 - 467
Zones
Location 340 341 342 343 344 345 346 347
Zone 1 2 0 0 0 1 3 0 1
(Default = Delay-1) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time Event Code Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 348 349 350 351 352 353 354 355
Zone 2 1 0 0 0 1 3 0 1
(Default = Handover) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time
Event Code
Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 356 357 358 359 360 361 362 363
Zone 3 1 0 0 0 1 3 0 1
(Default = Handover) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time Event Code Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 364 365 366 367 368 369 370 371
Zone 4 1 0 0 0 1 3 0 1
(Default = Handover) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time Event Code Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 372 373 374 375 376 377 378 379
Zone 5 1 0 0 0 1 3 0 1
(Default = Handover) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time Event Code Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 380 381 382 383 384 385 386 387
Zone 6 0 0 0 0 1 3 0 1
(Default = Instant) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time Event Code Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 388 389 390 391 392 393 394 395
Zone 7 0 0 0 0 1 3 0 1
(Default = Instant) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time
Event Code
Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 396 397 398 399 400 401 402 403
Zone 8 12 0 0 0 1 3 3 1
(Default = 24-Hr Burglary) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time
Event Code
Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 404 405 406 407 408 409 410 411
Zone 9 0 0 0 0 1 3 0 1
(Default = Instant) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time
Event Code
Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 412 413 414 415 416 417 418 419
Zone 10 0 0 0 0 1 3 0 1
(Default = Instant) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time
Event Code
Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 420 421 422 423 424 425 426 427
Zone 11 0 0 0 0 1 3 0 1
(Default = Instant) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time
Event Code
Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
6
0 = Unlimited Code Retries / 1 – 15 = Number Of Incorrect Code Retries
1 = 1K 5 = 3K9 9 = 10K 13 = Reserved
2 = 1K5 6 = 4K7 10 = 12K 14 = Reserved
3 = 2K2 7 = 5K6 11 = 22K 15 = Split EOL
4 = 3K3 8 = 6K8 12 = Reserved (3K3/6K8) 4
10 Solution-16/Solution-16 Safecom Quick Reference Guide
SOL 16 SAFECOM QUICK REF GUIDE.DOC.DOC Bosch Security Systems Pty Limited

Location 428 429 430 431 432 433 434 435
Zone 12 0 0 0 0 1 3 0 1
(Default = Instant) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time Event Code Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 436 437 438 439 440 441 442 443
Zone 13 0 0 0 0 1 3 0 1
(Default = Instant) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time Event Code Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 444 445 446 447 448 449 450 451
Zone 14 0 0 0 0 1 3 0 1
(Default = Instant) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time
Event Code
Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 452 453 454 455 456 457 458 459
Zone 15 0 0 0 0 1 3 0 1
(Default = Instant) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time
Event Code
Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Location 460 461 462 463 464 465 466 467
Zone 16 0 0 0 0 1 3 0 1
(Default = Instant) Zone
Type Zone Options Zone Pulse Count Zone Pulse Count Time Event Code Hundreds
Digit
Event code
Tens
Digit
Event Code
Units
Digit
Dialler
Channel
Zone Types
Zone Type Description Zone Type Description
0 Instant 8 Delay-1 (Auto Isolated In STAY Mode 1)
1 Handover 9 Delay 2 (Auto Isolated In STAY Mode 1)
2 Delay-1 10 Delay-3 (Auto Isolated In STAY Mode 1)
3 Delay-2 11 Delay-4 (Auto Isolated In STAY Mode 1)
4 Delay-3 12 24 Hour Burglary
5 Delay-4 13 24 Hour Fire
6 Instant (Auto Isolated In STAY Mode 1) 14 Chime
7 Handover (Auto Isolated In STAY Mode 1) 15 Not Used
Zone Options Dialler Channel
Option Description Option Group
1 Lockout Siren 1 Group 1 (Area 1)
2 Lockout Dialler 2 Group 2 (Area 2)
4 Silent Alarm 3 Group 3 (Area 3)
8 Sensor Watch 4 Group 4 (Area 4)
Zone Pulse Count
The pulse count allows you to program how many pulses (0 – 15) need to be registered within the pulse count
time to activate an alarm.
Zone Pulse Count Time
Option 20ms Loop Response Time Option 150 ms Loop Response Time
0 0.5 Seconds 8 20 Seconds
1 1 Second 9 30 Seconds
2 2 Seconds 10 40 Seconds
3 3 Seconds 11 50 Seconds
4 4 Seconds 12 60 Seconds
5 5 Seconds 13 90 Seconds
6 10 Seconds 14 120 Seconds
7 15 Seconds 15 200 Seconds
Event Code
The three-digit event code is used to describe the zone function when reporting in Contact ID format (Eg.
Entry/Exit, Tamper, Perimeter etc). Refer to the installation manual for a full list of Contact ID codes available.
When the system is reporting in a format other then Contact ID, the event code are programmed as follows:
Hundreds Digit = Alarm Restore Report (0 = Alarm Restore Disabled)
Tens Digit = Alarm Report (0 = Alarm Disabled)
Units Digit = Channel Code (0 = Disabled)
Solution-16/Solution-16 Safecom Quick Reference Guide 11
Bosch Security Systems Pty Limited

Location 468 - 469
Zone Bypass (Zones 1 – 8)
Location 470 - 471
Zone Bypass (Zones 9 – 16)
Location 472 - 473
Zone Trouble (Zones 1 – 8)
Location 474 - 475
Zone Trouble (Zones 9 – 16)
Location 476 - 479
Codepad Duress
Location 480 - 483
Codepad Panic
Location 484 - 487
Access Denied (Code Retries)
Location 488 - 491
AC Fail
Location 492 - 495
Low Battery
Location 496 - 499
Program Altered Code
Location 500 - 503
Sensor Watch (V1.10 – 1.31)
Location 500 - 503
Sensor Watch (V1.32+)
Location 504 - 505
Open/Close Reports For Area 1
Location 506 - 513
Test Report Time (Automatic)
Location 514 - 529
PET Pager Network Password
Telecom expects to see the password "passwd" sent before the message is transmitted. The password is programmed using ASCII text.
Location 530 - 539
PET Pager ID Number
The Pager ID Number locations are used to store the unique number that allows the network to identify individual pagers. When
programming the system to report via SMS messaging to a mobile phone, enter the mobile phone number as the PET pager ID number.
To program the Pager ID Number, enter the decimal characters that represent the Pager ID Number. Remember to substitute a 10 for a
zero and to terminate the number with a zero as you would if you were programming the telephone numbers.
9 9
Location 468 = Bypass Report
Location 469 = Bypass Restore Report
Location 470 = Bypass Report
Location 471 = Bypass Restore Report 9 9
9 9
Location 472 = Trouble Report
Location 473 = Trouble Restore Report
Location 474 = Trouble Report
Location 475 = Trouble Restore Report 9 9
1 2 1 1
Location 476 = 478 = Contact ID Event Code (Hundreds/Tens/Units)
Location 479 = Dialler Channel
1 2 0 1
Location 480 = 482 = Contact ID Event Code (Hundreds/Tens/Units)
Location 483 = Dialler Channel
4 2 1 1
Location 484 = 486 = Contact ID Event Code (Hundreds/Tens/Units)
Location 487 = Dialler Channel
3 0 1 1
Location 488 = 490 = Contact ID Event Code (Hundreds/Tens/Units)
Location 491 = Dialler Channel
3 0 9 1
Location 492 = 494 = Contact ID Event Code (Hundreds/Tens/Units)
Location 495 = Dialler Channel
3 0 6 0
Location 496 = 498 = Contact ID Event Code (Hundreds/Tens/Units)
Location 499 = Dialler Channel
3 8 3 1
Location 500 - 502 = Contact ID Event Code (Hundreds/Tens/Units)
Location 503 = Dialler Channel
3 0 7 1
Location 500 - 502 = Contact ID Event Code (Hundreds/Tens/Units)
Location 503 = Dialler Channel
Location 504 = Open Report
Location 505 = Close Report 8 9
Location 506 = Hour Of Day (Tens Digit)
Location 507 = Hour Of Day (Units Digit)
Location 508 = Minute Of Day (Tens Digit)
Location 509 = Minute Of Day (Tens Digit)
Location 510 = Repeat Interval (Tens Digit)
Location 511 = Repeat Interval (Units Digit)
Location 512 = Expansion Code
Location 513 = Test Report Options
506 507 508 509 510 511 512 513
0 0 0 0 0 0 9 0
H H M M Repeat
Interval Exp Option
Test Report Options
1 = Test Reports Only When Armed
2 = Test Reports On All Areas
7061737377640000
0000000000
12 Solution-16/Solution-16 Safecom Quick Reference Guide
SOL 16 SAFECOM QUICK REF GUIDE.DOC.DOC Bosch Security Systems Pty Limited

Location 540 - 623
Outputs
Location 540 541 542 543 544 545 Location 546 547 548 549 550 551
Output 1 0 0 0 0 0 0 Output 2 00 0 0 00
Default =
BOSCHSAT Event
Code Polarity Time Base Time Base Multiplier Default =
BOSCHSTU Event
Code Polarity Time Base Time Base Multiplier
Location 552 553 554 555 556 557 Location 558 559 560 561 562 563
Output 3 0 1 10 2 0 3 Output 4 20 1 0 00
Default = Smoke
Detector Reset Event
Code Polarity Time Base Time Base Multiplier Default = Strobe Event
Code Polarity Time Base Time Base Multiplier
Location 564 565 566 567 568 569 Location 570 571 572 573 574 575
Output 5 1 15 1 0 0 0 Output 6 012 2 1 0 1
Default = Sirens
Running Event
Code Polarity Time Base Time Base Multiplier Default = Codepad -
Entry /Exit+D’ Alarm Event Code Polarity Time Base Time Base Multiplier
Location 576 577 578 579 580 581 Location 582 583 584 585 586 587
Output 7 5 2 6 3 1 0 Output 8 52 6 3 60
Default = Area 1 In
Alarm (Siren) Event
Code Polarity Time Base Time Base Multiplier Default = Area 1 In
Alarm (Strobe) Event
Code Polarity Time Base Time Base Multiplier
Location 588 589 590 591 592 593 Location 594 595 596 597 598 599
Output 9 5 3 6 3 1 0 Output 10 53 6 3 60
Default = Area 2 In
Alarm (Siren) Event
Code Polarity Time Base Time Base Multiplier Default = Area 2 In
Alarm (Strobe) Event
Code Polarity Time Base Time Base Multiplier
Location 600 601 602 603 604 605 Location 606 607 608 609 610 611
Output 11 5 4 6 3 1 0 Output 12 54 6 3 60
Default = Area 3 In
Alarm (Siren) Event
Code Polarity Time Base Time Base Multiplier Default = Area 3 In
Alarm (Strobe) Event
Code Polarity Time Base Time Base Multiplier
Location 612 613 614 615 616 617 Location 618 619 620 621 622 623
Output 13 5 5 6 3 1 0 Output 14 55 6 3 60
Default = Area 4 In
Alarm (Siren) Event
Code Polarity Time Base Time Base Multiplier Default = Area 4 In
Alarm (Strobe) Event
Code Polarity Time Base Time Base Multiplier
Output Event Types
Event
Code Description Event
Code Description
0 0 BOSCHSAT – Satellite Siren (Output 1 Only) 14 AC Fail
0 0 BOSCHSTU – Securitel (Output 2 Only) 15 Low Battery
0 0 Serial Printer (Output 3 Only) 16 Horn Speaker Fail
0 1 System Armed 17 Sensor Watch Alarm
0 2 System Disarmed 18 Codepad Medical Alarm (V1.37+)
0 3 Armed In STAY Mode 19 Codepad Fire Alarm (V1.37+)
0 4 Pre-Arming Alert (V1.10) 110 Codepad Panic Alarm
0 4 Armed In AWAY (V1.20+) 111 Codepad Duress Alarm
0 5 Pre-Arming Alert (V1.20+) 112 Access Denied (Code Retries)
0 6 Exit Warning (All Zones Sealed)+Entry Warning 113 Speaker Beeps (V1.37+)
0 7 Exit Warning 114 Reserved
0 8 Exit Warning Finished 115 Sirens Running
0 9 Kiss-Off After End Of Exit Time 20 Strobe
0 10 Reserved 21 Silent Alarm
0 11 Entry Warning 22 Alarm In STAY Mode
0 12 Entry Warning + Day Alarm (Resetting) 2 3 Alarm In AWAY Mode
0 13 Reserved 2 4 Reserved
0 14 Day Alarm (Resetting) 2 5 Fire Alarm (Resetting)
0 15 Day Alarm Latching 2 6 Fire Alarm (Latching)
1 0 Day Alarm Enabled (V1.20+) 2 7 Fire Alarm (Verification)
1 1 Timed Output 2 8 Remote Control 1
1 2 Pre-Alert Warning For Timed Output 2 9 Remote Control 2
1 3 Reserved 2 10 Remote Control 3
Solution-16/Solution-16 Safecom Quick Reference Guide 13
Bosch Security Systems Pty Limited

Event
Code Description Event
Code Description
2 11 Remote Control 4 48 Reserved
2 12 Auxiliary Code 1 49 Reserved
2 13 Auxiliary Code 2 410 Area 1 - Zone Unsealed
2 14 Telephone Line Fail 411 Area 2 – Zone Unsealed
2 15 Communications Fail After 3 Attempts 412 Area 3 – Zone Unsealed
3 0 Communications Fail 413 Area 4 – Zone Unsealed
3 1 Dialler Disabled 414 Reserved
3 2 Dialler Active (On-Line) 415 Reserved
3 3 Ring Detect (V1.37+) 50 Reserved
3 4 Reserved 51 AC Main 50 Hz / 60 Hz
3 5 Mimic Zone 1 52 Area 1 In Alarm
3 6 Mimic Zone 2 53 Area 2 In Alarm
3 7 Mimic Zone 3 54 Area 3 In Alarm
3 8 Mimic Zone 4 55 Area 4 In Alarm
3 9 Mimic Zone 5 56 Area 1 Armed
3 10 Mimic Zone 6 57 Area 2 Armed
3 11 Mimic Zone 7 58 Area 3 Armed
3 12 Mimic Zone 8 59 Area 4 Armed
3 13 Mimic Zone 9 510 Area 1 Disarmed
3 14 Mimic Zone 10 511 Area 2 Disarmed
3 15 Mimic Zone 11 512 Area 3 Disarmed
4 0 Mimic Zone 12 513 Area 4 Disarmed
4 1 Mimic Zone 13 514 Any Areas Armed
4 2 Mimic Zone 14 515 Any Areas Disarmed
4 3 Mimic Zone 15 60 Area 1 Codepad Data Terminal
4 4 Mimic Zone 16 61 Area 2 Codepad Data Terminal
4 5 Chime 62 Area 3 Codepad Data Terminal
4 6 Zone Not Sealed 63 Area 4 Codepad Data Terminal
4 7 Reserved
Polarity (Modes)
Option Description Option Description
0 Disabled 7 Reserved
1 Normally Open, Going Low 8 Normally Low, Going Open
2 Normally Open, Pulsing Low 9 Normally Low, Pulsing Open
3 Normally Open, One Shot Low 10 Normally Low, One Shot Open
4 Normally Open, One Shot Low (Reset) 11 Normally Low, One Shot Open (Reset)
5 Normally Open, One Shot Low (Re-trigger) 12 Normally Low, One Shot Open (Re-trigger)
6 Normally Open, Latching Low 13 Normally Low, Latching Open
Time Base
Choose one of the options in the table below for the time base.
Option Description
1 200 ms
2 1 Second
3 1 Minute
4 1 Hour
Time Base Multiplier
Enter a value between 01 – 99.
One Shot Mode
When you program the output polarity as one shot, the time base is multiplied by the time base multiplier (Eg. If
the time base = 2 and the multiplier = 05, the output will operate for 5 seconds)
Pulsing Mode
When you program the output polarity as pulsing, the time base becomes the ‘ON’ time and the multiplier
becomes the ‘OFF’ time. The ‘OFF’ time is the time base x the multiplier (Eg. If you want the output to pulse
one (1) second ‘ON’ and five (5) seconds ‘OFF’, you would program time base as one (1) and the multiplier as
five (5)).
14 Solution-16/Solution-16 Safecom Quick Reference Guide
SOL 16 SAFECOM QUICK REF GUIDE.DOC.DOC Bosch Security Systems Pty Limited

Location 624 - 625
Entry Time 1
Location 626 - 627
Entry Time 2
Location 628 - 629
Entry Time 3
Location 630 - 631
Entry Time 4
Location 632 - 633
Exit Time For AWAY Mode
Location 634 - 635
Exit Time For STAY Mode 1
Location 636 - 637
Exit Time For STAY Mode 2
Location 638 - 639
Entry Guard Time
For STAY Mode 1 and 2
Location 640 - 641
Codepad Lockout Time
Location 642 - 643
Sensor Watch Time
Location 644 - 649
System Date (V1.10)
Location 644 - 649
System Date (V1.20+)
Location 650 - 653
Auto Arming Time
Location 654
Auto Arming Pre-Alert Time
Location 655
Timed Output
Pre-Alert Time
Location 656 - 659
Auto Operation Of The
Timed Output
10 0
Location 624 = Increments Of 1 Second (0 – 15 Seconds)
Location 625 = Increments Of 16 Seconds (0 – 240 Seconds)
Location 626 = Increments Of 1 Second (0 – 15 Seconds)
Location 627 = Increments Of 16 Seconds (0 – 240 Seconds) 4 1
14 1
Location 628 = Increments Of 1 Second (0 – 15 Seconds)
Location 629 = Increments Of 16 Seconds ( 0 – 240 Seconds)
Location 630 = Increments Of 1 Second (0 – 15 Seconds)
Location 631 = Increments Of 16 Seconds (0 – 240 Seconds) 8 2
12 3
Location 632 = Increments Of 1 Second (0 – 15 Seconds)
Location 633 = Increments Of 16 Seconds (0 – 240 Seconds)
Location 634 = Increments Of 1 Second (0 – 15 Seconds)
Location 635 = Increments Of 16 Seconds (0 – 240 Seconds) 12 3
12 3
Location 636 = Increments Of 1 Second (0 – 15 Seconds)
Location 637 = Increments Of 16 Seconds ( 0 – 240 Seconds)
Location 638 = Increments Of 1 Second (0 – 15 Seconds)
Location 639 = Increments Of 16 Seconds (0 – 240 Seconds) 12 3
Location 640 = Increments Of 1 Second (0 – 15 Seconds)
Location 641 = Increments Of 16 Seconds (0 – 240 Seconds) 0 0
Location 642 = Increments Of Days (Tens Digit)
Location 643 = Increments Of Days (Units Digit) 0 0
Location 644 = Day Of The Week (Sun = 1 Sat = 2)
Location 645 = Month Of The Year (Jan = 1 Dec = 12)
Location 646 = Day Of The Month (Tens Digit)
Location 647 = Day Of The Month (Units Digit)
Location 648 = Current Year (Tens Digit)
Location 649 = Current Year (Units Digit)
644 645 646 647 648 649
1 1 0 1 9 5
D M D D Y Y
Location 644 = Day Of The Month (Tens Digit)
Location 645 = Day Of The Month (Units Digit)
Location 646 = Month Of The Year (Tens Digit)
Location 647 = Month Of The Year (Units Digit)
Location 648 = Current Year (Tens Digit)
Location 649 = Current Year (Units Digit)
644 645 646 647 648 649
0 1 0 1 9 5
D D M M Y Y
Location 650 = Hour Of The Day (Tens Digit)
Location 651 = Hour Of The Day (Units Digit)
Location 652 = Minute Of The Day (Tens Digit)
Location 653 = Minute Of The Day (Units Digit)
650 651 652 653
0 0 : 0 0
H H M M
5
0 = No Pre-Alert Time / 1 - 15 = Pre-Alert Time In Minutes (Default = 5 Min’s)
5
0 = No Pre-Alert Time / 1 - 15 = Pre-Alert Time In Minutes (Default = 5 Min’s)
Location 656 = Hour Of The Day (Tens Digit)
Location 657 = Hour Of The Day (Units Digit)
Location 658 = Minute Of The Day (Tens Digit)
Location 659 = Minute Of The Day (Units Digit)
656 657 658 659
0 0 : 0 0
H H M M
Solution-16/Solution-16 Safecom Quick Reference Guide 15
Bosch Security Systems Pty Limited

Location 660
Siren Run Time (V1.10 – 2.03)
Location 660
Siren Run Time (V2.04+)
Location 661
Siren Sound Rate
Location 662
Swinger Shutdown Count
For Siren and Dialler (V1.10 – 1.37)
Location 662
Swinger Shutdown Count
For Siren (V1.40+)
Location 663
Dialler Options 1
Location 664
Dialler Options 2
Location 665
System Options 1
Location 666
System Options 2
Location 667
System Options 3
Location 668
System Options 4 (V1.10 Only)
Location 668
System Options 4 (V1.20+)
Location 669
Consumer Options 1 (V1.10 Only)
Location 669
Consumer Options 1 (V1.20+)
Location 670
Consumer Options 2
10
0 = No Siren Time / 1 - 15 = Siren Time In Minutes (Default = 10 Min’s)
5
0 = No Siren Time / 1 - 15 = Siren Time In Minutes (Default = 5 Min’s)
7
0 = Slowest Frequency / 15 = Fastest Frequency
0
0 = No Lockout / 1 - 15 = Number Of Times Siren/Dialler Operate Till Lockout
0
0 = No Lockout / 1 - 15 = Number Of Times Siren Operate Till Lockout
5
1 = Dialler Reporting Functions Allowed (Disable In V2.00 Also Disable Safecom)
2 = Remote Arming Via Telephone Allowed
4 = Upload/Download Via Alarm Link Allowed
8 = Terminate Alarm Link Session On Alarm
0
1 = Open/Close Reports Only After Alarm
2 = First To Open/Last To Close Reporting (Partitioned Systems Only)
4 = Open/Close Reports In STAY Mode Allowed
8 = Answering Machine Bypass Only When Armed (V1.31 +)
1
1 = Forced Arming Allowed
2 = Smart Lockout Allowed
4 = Horn Speaker Monitor
8 = Horn Speaker Beeps Allowed
2
1 = Keyswitch Interface, Night Arm Station or RE005 Installed
2 = Handover Delay To Be Sequential
4 = Codepad Panic To Be Silent
8 = Access Denied (Code Retries/Codepad Tamper) To Be Silent
0
1 = Area 1 Codepad Connected To Main Data Terminal
2 = Modem Module Required For Alarm Link Operation
4 = AC Fail After 1 Hour (Disabled = After 2 Minutes)
8 = Pulse Count Handover Allowed
0
1 = Delay Audible Alarm Until Communication Complete
2 = Reset Alarm Outputs From Any Area (Partitioned Systems Only)
4 = Auto Arm In AWAY Mode
8 = Auto Arm In STAY Mode 1
0
1 = Delay Audible Alarm Until Communication Complete
2 = Reset Alarm Outputs From Any Area (Partitioned Systems Only)
4 = Ignore AC Mains Fail (V1.30+)
8 = Auto Arm In STAY Mode 1
2
1 = Entry Guard Time In STAY Mode
2 = Audible Alarm In STAY Mode Allowed
4 = User Code Required To Isolate Zones
8 = Codepad Extinguish Mode Allowed
2
1 = STAY LED To Display Day Alarm On/Off Status
2 = Audible Alarm In STAY Mode Allowed
4 = AUX LED To Display Dialler On-Line (Partitioned Codepad Only)
8 = Codepad Extinguish Mode Allowed
2
1 = ‘User Code + 0 + AWAY’ Function To Arm/Disarm All Areas Allowed
2 = Single Button Arming Allowed (AWAY, STAY Mode 1 & STAY Mode 2)
4 = Single Button Disarm Allowed (STAY Mode 1 or STAY Mode 2)
8 = Alarm Reset Memory On Disarm
16 Solution-16/Solution-16 Safecom Quick Reference Guide
SOL 16 SAFECOM QUICK REF GUIDE.DOC.DOC Bosch Security Systems Pty Limited

Location 671
DTMF Command Module
Options
Location 672
Expansion Board Options (V1.10)
Location 672
Expansion Board Options V1.20+)
Location 673
Telephone Line Fail Options
Location 674 - 675
Open/Close Reports For Area 2
Location 676 - 677
Open/Close Reports For Area 3
Location 678 - 679
Open/Close Reports For Area 4
Location 680 - 683
Subscriber ID Number For Area 2
Location 684 - 687
Subscriber ID Number For Area 3
Location 688 - 691
Subscriber ID Number For Area 4
Location 692 - 699
Zone Allocations For Area 1
Location 700 - 707
Zone Allocations For Area 2
0
1 = Access To Installer’s Programming Mode Allowed
2 = Installer Code Functions Allowed
4 = Disarming and Auxiliary Code Functions Allowed
8 = Master Code Functions Allowed
0
1 = Zone Expansion Board Installed
2 = Output Expansion Board Installed
4 = Momentary Keyswitch Input
8 = Latching Keyswitch Input
1 = Zone Expansion Board Installed 7 = Momentary Arm In STAY Mode 2
2 = Output Expansion Board Installed 8 = Momentary Disarm
3 = Momentary Keyswitch Input 9 = Momentary Arm Area 4
4 = Latching Keyswitch Input 10 = Momentary Disarm Area 4
5 = Momentary Arm In AWAY Mode 11 = Momentary Arm/Disarm Area 4
6 = Momentary Arm In STAY Mode 1 12 = Latching Arm/Disarm Area 4 0
0
1 = Display FAULT Indicator If Telephone Line Fails
2 = Sound Alarm When System Is Armed If Telephone Line Fails
4 = Sound Alarm When System Is Disarmed If Telephone Line Fails
Note: Option 2 & 4 Must Be Used In Conjunction With Option 1
(Eg. Program a 1, 3, 5 or 7)
Location 674 = Open Report
Location 675 = Close Report 0 0
Location 676 = Open Report
Location 677 = Close Report 0 0
Location 678 = Open Report
Location 679 = Close Report 0 0
0000
0000
0000
Location 692 = Zone 1 LED – Area 1 Codepad
Location 693 = Zone 2 LED – Area 1 Codepad
Location 694 = Zone 3 LED – Area 1 Codepad
Location 695 = Zone 4 LED – Area 1 Codepad
Location 696 = Zone 5 LED – Area 1 Codepad
Location 697 = Zone 6 LED – Area 1 Codepad
Location 698 = Zone 7 LED – Area 1 Codepad
Location 699 = Zone 8 LED – Area 1 Codepad
692 693 694 695 696 697 698 699
0 0 0 0 0 0 0 0
Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8
Location 700 = Zone 1 LED – Area 2 Codepad
Location 701 = Zone 2 LED – Area 2 Codepad
Location 702 = Zone 3 LED – Area 2 Codepad
Location 703 = Zone 4 LED – Area 2 Codepad
Location 704 = Zone 5 LED – Area 2 Codepad
Location 705 = Zone 6 LED – Area 2 Codepad
Location 706 = Zone 7 LED – Area 2 Codepad
Location 707 = Zone 8 LED – Area 2 Codepad
700 701 702 703 704 705 706 707
0 0 0 0 0 0 0 0
Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8
Solution-16/Solution-16 Safecom Quick Reference Guide 17
Bosch Security Systems Pty Limited

Location 708 - 715
Zone Allocations For Area 3
Location 716 - 723
Zone Allocations For Area 4
Location 724 - 755
User Code Area Assignment
Location 724 725 726 727 728 729
User Code 1 0 User Code 2 0 User Code 3 0User Code 4 0User Code 5 0 User Code 6 0
Location 730 731 732 733 734 735
User Code 7 0 User Code 8 0 User Code 9 0User Code 10 0User Code 11 0 User Code 12 0
Location 736 737 738 739 740 741
User Code 13 0 User Code 14 0 User Code 15 0User Code 16 0User Code 17 0 User Code 18 0
Location 742 743 744 745 746 747
User Code 19 0 User Code 20 0 User Code 21 0User Code 22 0User Code 23 0 User Code 24 0
Location 748 749 750 751 752 753
User Code 25 0 User Code 26 0 User Code 27 0User Code 28 0User Code 29 0 User Code 30 0
Location 754 755
User Code 31 0 User Code 32 0
Location 756
Serial Printer Baud Rate
Location 757
Dialler Lockout Count (V1.40+)
Location 760 - 763
Safecom – RF Fail (V2.00+)
Location 764 - 767
Safecom – Telco Fail (V2.00+)
Location 768 - 771
Safecom – RF Jamming (V2.00+)
Location 708 = Zone 1 LED – Area 3 Codepad
Location 709 = Zone 2 LED – Area 3 Codepad
Location 710 = Zone 3 LED – Area 3 Codepad
Location 711 = Zone 4 LED – Area 3 Codepad
Location 712 = Zone 5 LED – Area 3 Codepad
Location 713 = Zone 6 LED – Area 3 Codepad
Location 714 = Zone 7 LED – Area 3 Codepad
Location 715 = Zone 8 LED – Area 3 Codepad
708 709 710 711 712 713 714 715
0 0 0 0 0 0 0 0
Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8
Location 716 = Zone 1 LED – Area 4 Codepad
Location 717 = Zone 2 LED – Area 4 Codepad
Location 718 = Zone 3 LED – Area 4 Codepad
Location 719 = Zone 4 LED – Area 4 Codepad
Location 720 = Zone 5 LED – Area 4 Codepad
Location 721 = Zone 6 LED – Area 4 Codepad
Location 722 = Zone 7 LED – Area 4 Codepad
Location 723 = Zone 8 LED – Area 4 Codepad
716 717 718 719 720 721 722 723
0 0 0 0 0 0 0 0
Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8
0 = User Code Not Assigned
1 = User Code Assigned To Area 1
2 = User Code Assigned To Area 2
4 = User Code Assigned To Area 3
8 = User Code Assigned To Area 4
2
1 = 300 Baud
2 = 600 Baud
3 = 1200 Baud
4 = 2400 Baud
0
0 = No Lockout / 1 - 15 = Number Of Times Dialler Operate Till Lockout
3 5 3 1
Location 760 = 762 = Contact ID Event Code (Hundreds/Tens/Units)
Location 763 = Dialler Channel (Point ID = 30 Hex / 48 Decimal)
3 5 1 1
Location 764 = 766 = Contact ID Event Code (Hundreds/Tens/Units)
Location 767 = Dialler Channel (Point ID = 31 Hex / 49 Decimal)
3 4 4 1
Location 768 = 770 = Contact ID Event Code (Hundreds/Tens/Units)
Location 771 = Dialler Channel (Point ID = 32 Hex / 50 Decimal)
18 Solution-16/Solution-16 Safecom Quick Reference Guide
SOL 16 SAFECOM QUICK REF GUIDE.DOC.DOC Bosch Security Systems Pty Limited

Location 772
Safecom – RF Jamming Delay
(V2.00+)
Location 773
Safecom RF Supervision Time
(V2.02+)
Location 846 – 847
Ring Burst Time (V2.04)
Location 846 – 847
Ring Burst Time (V2.05+)
Location 896
Safecom Reporting Options
(V2.00+)
Location 897
System Options 5 (V1.37+)
Location 898
System Options 6 (V1.33+)
Location 899
Carrier Sync Options
Location 900
Default Options
Location 901 - 904
System Time
Location 920 - 927
Safecom Interface Serial Number
The eight-digit serial number of the Safecom interface board can be read in the above
locations.
Connection For Momentary Or Latching Keyswitch
To enable the connection for a momentary or latching
keyswitch on the above diagram, refer to “LOCATION
672” under Expansion Board Type to program these
options.
0
0 = No RF Jamming Delay / 1 - 15 = RF Jamming Delay In Minutes
10
0 = No RF Supervision Time / 1 - 15 = RF Supervision Time In Minutes
Location 846 = Increments Of 5 ms (0 ms – 75 ms)
Location 847 = Increments Of 80 ms (0 ms – 1200 ms) 0 0
Location 846 = Increments Of 5 ms (0 ms – 75 ms)
Location 847 = Increments Of 80 ms (0 ms – 1200 ms) 4 6
6
1 = Safecom Communication Reporting Disabled
2 = Arming From ST1000 Base Allowed
4 = Disarming From ST100 Base Allowed
8 = Reserved
0
1 = Send ‘Test’ Report At End Of Siren Time
2 = Power Up In Disarmed State (Re-Boot)
4 = Internal Crystal To Keep Time (V1.40+)
8 = Reserved
3
1 = Busy Tone Detection For Domestic Dialling Allowed
2 = ‘Kiss-Off’ Detection For Domestic Dialling Allowed
4 = Extend Acknowledge Time From 30 To 60 Seconds
8 = If Battery Failed, Restrict Battery Test Only On Arming (V1.35+)
9
1 = 100 ms - 15 = 1.5 Seconds (Increments Of 100 ms)
0
0 = Defaulting System Allowed / 15 = Defaulting System Disabled
Location 901 = Hour Of The Day (Tens Digit)
Location 902 = Hour Of The Day (Units Digit)
Location 903 = Minute Of The Day (Tens Digit)
Location 904 = Minute Of The Day (Units Digit)
901 902 903 904
0 0 : 0 0
H H M M
0 0 0 0 0 0 0 0
Solution-16/Solution-16 Safecom Quick Reference Guide 19
Bosch Security Systems Pty Limited

Connections For Split EOL Resistors For 16 Zone Operation
Connections For Split EOL Resistors For 16 Zone Operation Using N/O Contacts
Safecom Interface
20 Solution-16/Solution-16 Safecom Quick Reference Guide
SOL 16 SAFECOM QUICK REF GUIDE.DOC.DOC Bosch Security Systems Pty Limited