Bosch MAP Control Center IUI-MAP0001-2 User manual

MAP Control Center
IUI‑MAP0001‑2
en User manual

MAP Control Center Table of contents | en 3
Bosch Security Systems B.V. User manual 2019-11 | 08 | F.01U.168.328
Table of contents
1Safety 5
2Short information 6
2.1 Introduction 6
2.2 Ambient conditions 6
2.3 Certifications 6
3System overview 8
3.1 Housing with LEDs 8
3.2 LCD screen 8
3.3 Main menu 8
4Getting started 11
4.1 Idle mode 11
4.2 Logging in 11
4.3 Logging off 11
5Operation 12
5.1 Handling alarms 12
5.1.1 Silencing alarms 12
5.1.2 Clearing alarms and events 12
5.1.3 Viewing event memory 12
5.1.4 Clearing an anti-masking message 12
5.2 Search and sort functions 13
5.3 Arming areas 13
5.4 Disarming areas 15
5.5 Managing users 16
5.5.1 Adding users 16
5.5.2 Deleting users 18
5.5.3 Editing users 18
5.5.4 Changing passcode 20
5.6 Schedules 21
5.7 System status 21
5.7.1 Viewing area status 22
5.7.2 Viewing device status 22
5.7.3 Bypassing/unbypassing devices 23
5.7.4 Unbypassing all devices 23
5.8 System service functions 23
5.8.1 Event history 24
5.8.2 Viewing version information 25
5.8.3 Enabling/disabling device 26
5.8.4 Setting time and date 26
5.8.5 Walk test 26
5.8.6 Motion detector test 28
5.8.7 Bell and indicator test 29
5.8.8 Changing/viewing output state 29
5.8.9 Manufacturer authorization 29
5.8.10 Adjusting volume/brightness 30
5.8.11 Setting chime mode 30
5.8.12 Blocking time 30
5.9 Internal programs 32
5.10 Event memory 32

4en | Table of contents MAP Control Center
2019-11 | 08 | F.01U.168.328 User manual Bosch Security Systems B.V.
5.11 Managing remote access 33
6Troubleshooting 34
7Maintenance 35

MAP Control Center Safety | en 5
Bosch Security Systems B.V. User manual 2019-11 | 08 | F.01U.168.328
1 Safety
Danger!
Electricity
Injuries due to electricity are possible if the system is not operated correctly or if the system
is opened or modified.
– Never open or modify the system.
– Please contact your installer if you want to get your system modified.
!
Caution!
Sensitive components
Damage of sensitive components is possible if the system is not handled carefully or if the
system is opened or modified.
– Always handle the system carefully.
– Never open or modify the system.
– Please contact your installer if you want to get your system modified.
Old electrical and electronic appliances
Electrical or electronic devices that are no longer serviceable must be collected separately and
sent for environmentally compatible recycling (in accordance with the European Waste
Electrical and Electronic Equipment Directive).
To dispose of old electrical or electronic devices, you should use the return and collection
systems put in place in the country concerned.

6en | Short information MAP Control Center
2019-11 | 08 | F.01U.168.328 User manual Bosch Security Systems B.V.
2 Short information
This manual describes how to operate the MAP control center.
2.1 Introduction
The MAP control center is an input device for the MAP 5000 system.
Each control center has a vibrant-color 14cm (5.7inch) LCD screen. The durable touch screen
provides access to system functions through an interface with intuitive buttons. Users touch
the images directly on the screen to arm, disarm, or select other menu options. The display
text is shown in the language defined by the user.
2.2 Ambient conditions
Environmental
Minimum operating temperature in °C -10
Maximum operating temperature in °C 55
Minimum storage temperature in °C -20
Maximum storage temperature in °C 60
Minimum relative humidity in % 5
Maximum relative humidity in % 95
Protection class IP30
IP31 (with an edge protection profile)
Security level IK06
Environmental class II:
EN60950-1, EN50130-4, EN50131-1,
VdS2110
Usage Indoor
2.3 Certifications
The system is designed to comply with the certifications and approvals listed here.
Region Agency Certification
Germany VdS Class C, VdS G 111040
Europe CE Conformité Européene
Europe EN EN 50131-1:2006 + A1:2009
EN 50131-3:2009
EN 50131-6:2008
EN 50136-2/SP4/DP3
EN 50131-10
Switzerland SES Association of Swiss Installers of Security Systems
Edition V3 / 01.01.2011-d
France AFNOR / CNPP
Cert.
NF&A2P Grade 3
Certificate Number ICP-MAP5000-2: 1133400003
Certificate Number ICP-MAP5000-COM: 1230200016

MAP Control Center Short information | en 7
Bosch Security Systems B.V. User manual 2019-11 | 08 | F.01U.168.328
According to NF324-H58

8en | System overview MAP Control Center
2019-11 | 08 | F.01U.168.328 User manual Bosch Security Systems B.V.
3 System overview
The MAP control center consists of a housing with three LEDs and an LCD screen.
3.1 Housing with LEDs
Three light-emitting diodes (LEDs) are located on the left edge of the MAP control center
housing:
Element Component Description
1 Green LED Indicates that the control center is in normal condition.
2 Yellow LED Indicates that there is a trouble condition, that devices are
covered, or that devices of the system are bypassed or
disabled.
3 Red LED The default behavior indicates that an alarm condition exists
in the security system.
3.2 LCD screen
How to operate the LCD screen
– To operate the LCD screen, tap the icons and buttons shown on the screen with
moderate pressure.
– To avoid damage of the LCD screen, do not use sharp objects during operation.
3.3 Main menu
Notice!
The buttons on your touch screen are determined by the user authorization level that has
been configured by the installer. Therefore, your touch screen might be different from what is
described in this manual.

MAP Control Center System overview | en 9
Bosch Security Systems B.V. User manual 2019-11 | 08 | F.01U.168.328
Main menu - screen 1
Element Component Description
1 Screen name This information identifies the active screen.
2 Menu buttons These buttons are used to perform tasks.
3 Installer mode icon This icon indicates that the control panel is in installer
mode.
4 RPS connected icon This icon indicates that remote programming software is
connected to the control panel.
5 Information button This buttons is used to view additional system information
and to clear events, alarms or troubles.
Flashing red: not yet cleared system events and alarms
Flashing yellow: not yet cleared system troubles
Green: no additional system information available
6 Navigation bar These buttons are used to navigate through the system, to
find tasks or to view system information. Grayed out
buttons are not activated.

10 en | System overview MAP Control Center
2019-11 | 08 | F.01U.168.328 User manual Bosch Security Systems B.V.
Main menu - screen 2
Navigation bar buttons
Element Component Description
Back Shows the previous screen.
Home Shows the main menu.
Page-up Shows the previous page on screens with more than one
page.
Page-down Shows the next page on screens with more than one page.
Help Shows helpful information about the active screen.
Exit Logs the user off and switches the display to the idle
screen.

MAP Control Center Getting started | en 11
Bosch Security Systems B.V. User manual 2019-11 | 08 | F.01U.168.328
4 Getting started
This chapter describes how to log in and off.
4.1 Idle mode
When the control center is not in use, an idle screen is displayed.
How to remove the idle screen
4To remove the idle mode and to view the login screen, touch the screen.
4.2 Logging in
How to log in
1. To view the login screen, tap the screen.
2. In the passcode field, enter your passcode.
The user passcode is a combination of the 3-digit user ID and a 6-digit password (e.g.
004123456).
If the passcode is correct, the Main Menu is displayed.
Invalid passcode
If the passcode is not correct, an error message is displayed.
4To empty the passcode field, press .
When an incorrect passcode has been entered ten times, the control center is locked for two
minutes per default. These values can be configured by the installer.
How to reset the password
4For more information on how to reset a password, refer to How to reset a passcode, page
19.
4For more information, contact your installer or system administrator.
4.3 Logging off
How to log off
4To log off, press .
Automatic log off
A user is logged off automatically if there has been no activity for two minutes. This value can
be configured by the installer.
4For more information, contact your installer or system administrator.

12 en | Operation MAP Control Center
2019-11 | 08 | F.01U.168.328 User manual Bosch Security Systems B.V.
5 Operation
This chapter describes all user operations.
5.1 Handling alarms
This chapter describes how to handle alarms and other events.
5.1.1 Silencing alarms
How to silence the acoustic alarm of the local control center
4Touch the screen of the local control center.
PThe login screen is displayed and the acoustic alarm on the local control center is
silenced.
How to silence all acoustic alarms of remote devices
1. Log in to display all acoustic alarms. Refer to How to log in, page 11.
The first and last alarms are displayed immediately.
2. To silence the alarms of all remote acoustic devices and control centers, press .
PThe alarms of all remote acoustic devices and control centers are silenced.
5.1.2 Clearing alarms and events
How to clear alarms and events
1. To view all current alarms and events, press .
All current alarms and events are displayed.
2. Read through the detailed information of the events listed and resolve the issues, if
necessary.
3. To clear the alarms and events, press .
PAll alarms and events are cleared.
Missing Authorization
If you do not have permission to clear alarms and events, an error message is displayed.
To get further assistance:
4For more information, contact your installer or system administrator.
5.1.3 Viewing event memory
When the icon flashes red or yellow, an event can be viewed in the event memory.
How to view the event memory
1. To view the event memory, press .
The newest events are displayed first.
2. Clear events if necessary.
5.1.4 Clearing an anti-masking message
How to clear an anti-masking message
An anti-masking message appears, if an object is placed in front of a motion detector that is
capable of detecting masking attempts.
1. Start the motion detector test for the area in which the motion detector is located. Refer
to Motion detector test, page 28.
2. Remove the object masking the motion detector.
3. Trigger the detector using motion.

MAP Control Center Operation | en 13
Bosch Security Systems B.V. User manual 2019-11 | 08 | F.01U.168.328
4. Stop the motion detector text.
PThe anti-masking message is cleared.
5.2 Search and sort functions
Whenever searching or sorting is possible, the corresponding search and sort buttons appear.
Search and sort buttons
Element Component Description
Search Shows an alphanumeric keypad screen.
Sort/filter Shows a list of sort categories appropriate to the function
and the A-Z and Z-A sort functions:
–A-Z: Alphabetical order
–Z-A: Reverse alphabetical order
How to search
1. Press .
The alphanumeric keypad screen appears.
2. Insert a search term with the alphanumeric keypad and the following commands:
Component Description
Shift Creates capital letters when pressed once.
Clear Clears all input.
Space Inserts a space.
Backspace Clears the last character.
Enter Starts the search process.
How to sort
1. To sort functions, press .
The buttons for alphabetical sorting appear.
2. To sort from A to Z, press A-Z.
Tor sort from Z to A, press Z-A.
How to filter
1. To filter, press .
The buttons showing the possible filter selections appear. The possible filter selections
depend on the currently displayed menu. For example, areas can be filtered by their
arming status and devices can be filtered by their fault or bypass status.
2. Choose a filter selection.
5.3 Arming areas
Notice!
If smartkey or blocklock controls are installed for your system, areas can only be armed with
these controls. A control center cannot be used to arm areas.
To get further assistance:

14 en | Operation MAP Control Center
2019-11 | 08 | F.01U.168.328 User manual Bosch Security Systems B.V.
4For more information, contact your installer or system administrator.
How to open the Arm menu
4To open the Arm menu, press and .
PThe Arm menu with three menu options is displayed.
The Arm menu
– Option 1: Arm predefined local area
Choose this option to arm a predefined area in one step. For this option one customer-
specific area can be defined.
– Option 2: Arm All Areas
Choose this option to arm all configured areas in one step. The configured areas are
defined by the installer for each user.
– Option 3: Arm Selected Areas
Choose this option to arm one or several areas from a list. Access to blocking time menu.
How to arm
4Select one of the three menu options to proceed.
The area and their current arming possibility are displayed.
– An area is ready to arm, if the icon is displayed.
– An area is not ready to arm, if the icon is displayed.
How to arm, if area is ready to arm
An area is ready to arm, if the icon is displayed. All devices in this area are in normal
state.
1. To arm an area that is ready to arm, press the desired option or area.
2. Press .
A countdown starts, indicating the remaining time to exit the location.
3. Exit the area within the remaining time of the countdown.
PThe area is armed.
How to make an area ready to arm
An area is not ready to arm, if the icon is displayed. There are active or faulted devices in
the area.
1. To arm an area that is not ready to arm, press the desired option or area.
2. Press .
All active or faulted devices, that either can be bypassed or cannot be bypassed, are
displayed.
3. Resolve the issues of the listed devices to make this area ready to arm.
Notice!
In case a blocking time interval is configured for an area, the icon is displayed under
Arm Selected Areas.
4To access the Blocking Time menu, select the area and press .
4For more information on blocking time, refer to Blocking time, page 30.

MAP Control Center Operation | en 15
Bosch Security Systems B.V. User manual 2019-11 | 08 | F.01U.168.328
Forced arming
!
Caution!
If you press Force Arm, all active or faulted devices are ignored and the area will be armed.
Press this button only if you intend to arm an area without the protection of the affected
devices.
Force Arm is only selectable, if all preconditions are fulfilled to allow arming an area with
active or faulted devices. Depending on regional standards and the system configuration,
these preconditions can differ.
In general, the Force Arm button is activated, if the following preconditions are fulfilled:
– The area contains no devices that are not allowed to be bypassed. These devices have the
information Cannot Bypass During Force Arming.
– The system configuration allows that a certain number of devices can be bypassed. These
devices have the information May Bypass.
How to force arm
4If you want to arm the area without the devices listed and if the preconditions are
fulfilled, press Force Arm.
5.4 Disarming areas
Notice!
If smartkey or blocklock controls are installed for your system, areas can only be disarmed
with these controls. A control center cannot be used to disarm areas.
To get further assistance:
4For more information, contact your installer or system administrator.
How to open the Disarm menu
4To open the Disarm menu, press and .
PThe Disarm menu with three menu options is displayed.
The Disarm menu
– Option 1: Disarm predefined local area
Choose this option to disarm a predefined area in one step. For this option one customer-
specific area can be defined.
– Option 2: Disarm All Areas
Choose this option to disarm all configured areas in one step. The configured areas are
defined by the installer for each user.
– Option 3: Disarm Selected Areas
Choose this option to disarm one or several areas from a list. Access to blocking time
menu.
How to disarm
1. Select one of the three menu options to proceed.
The area and their current arming status are displayed. An area is armed and can be
disarmed if the icon is displayed.
2. To disarm an area, press the desired option or area.
3. Press .
PThe area is disarmed.

16 en | Operation MAP Control Center
2019-11 | 08 | F.01U.168.328 User manual Bosch Security Systems B.V.
Notice!
In case a blocking time interval is configured for an area, the icon is displayed under
Disarm Selected Areas. The area for which the blocking time interval is configured cannot be
disarmed outside of this blocking time interval.
4To access the Blocking Time menu, select the area and press .
4For more information on blocking time, refer to Blocking time, page 30.
5.5 Managing users
Users can be added, deleted and edited and passwords can be changed. These options can be
restricted for certain user profiles according to the configuration of the installer.
4For more information, contact your installer or system administrator.
5.5.1 Adding users
How to open the Users menu
4To open the Users menu, press and .
PThe Users menu with four menu options is displayed.
How to add a new user
4Press Add User.
The options that can be set for a user are displayed.
To add a user, the following options are mandatory:
–Enter User ID
–Enter User Name
–Add Control Center User
The option Add Smartkey User is optional.
How to add a user ID
1. Press Enter User ID.
The user ID options are displayed.
2. To let the system automatically select a user ID, press Request Next Available User ID.
To manually select a user ID, press Enter User ID and type in the user ID.
3. To confirm the user ID, press .
The user options are displayed.
How to add a user name
1. Press Enter User Name.
The user name options are displayed.
2. To enter the first name of the user, press Enter User First Name.
3. Use the alphanumeric keypad to enter the name.
4. Press Enter.
5. To enter the last name of the user, press Enter User Last Name.
6. Use the alphanumeric keypad to enter the name.
7. Press Enter.
8. To confirm the first and last name, press .
The user options are displayed.

MAP Control Center Operation | en 17
Bosch Security Systems B.V. User manual 2019-11 | 08 | F.01U.168.328
Optional: Smartkey users
Notice!
This option can only be used if a smartkey profile is configured by the installer.
4For more information, contact your installer or system administrator.
How to add a smartkey user
1. Press Add Smartkey User.
The smartkey options are displayed.
2. To enter the ID of the smartkey token, press Enter Smartkey Token Number.
3. Use the alphanumeric keypad to enter the 8-character ID found on the smartkey token in
the Enter field.
4. To confirm, press .
5. To verify, use the alphanumeric keypad to enter the 8-character ID found on the smartkey
token in the Verify Code field.
6. To confirm the ID, press .
The smartkey options are displayed.
7. Press Select Smartkey Profile.
The predefined smartkey profiles are displayed. If no predefined smartkey profile is
available, an error message is displayed.
8. Select a predefined smartkey profile.
9. To confirm, press .
The user options are displayed.
How to add a control center user
1. Press Add Control Center User.
The control center options are displayed.
2. Press Select User Type.
3. Choose between Standard User and Temporary User.
The icon indicates the selection.
4. In case of a temporary user, enter the number of days for which the user is activated (0 -
99).
If you enter 0, the temporary user will be an inactive user. Inactive users can be activated
by the installer.
5. To confirm the temporary user duration, press .
6. To confirm the user type, press .
The control center user options are displayed.
7. Press Select User Profile.
8. Choose between Installer Profile, Owner/Facility Manager, Standard User and Super
User.
The icon indicates the selection.
9. To confirm the user profile, press .
The control center user options are displayed.
10. Press Select User Language.

18 en | Operation MAP Control Center
2019-11 | 08 | F.01U.168.328 User manual Bosch Security Systems B.V.
11. Choose one of the displayed languages.
The icon indicates the selection.
12. To confirm the user language, press .
The control center user options are displayed.
13. Press Select Exit Delay.
14. Choose between Standard and Extended.
The icon indicates the selection.
15. To confirm the exit delay option, press .
The control center user options are displayed.
16. To confirm the control center user options, press .
The user options are displayed.
How to finish adding a user
4After all control center user options are entered, press to add the user.
A confirmation message is displayed.
The Users menu is displayed.
PThe new user has been added.
Passcode of a new user
The default passcode is a combination of the 3-digit user ID and a 6-digit password. The 6-
digit password default value is 000000.
4For information on how to change the default password to an individual password, refer
to How to change the passcode, page 21.
5.5.2 Deleting users
How to open the Users menu
4To open the Users menu, press and .
PThe Users menu with four menu options is displayed.
How to delete users
1. Press Delete Users.
A list of the users is displayed.
2. Select the user you want to delete.
3. A confirmation message is displayed.
4. To delete the selected user, press .
PThe selected user is deleted.
5.5.3 Editing users
How to open the Users menu
4To open the Users menu, press and .
PThe Users menu with four menu options is displayed.
How to edit a user
1. Press Edit User.
A list of the users is displayed.
2. Select the user you want to edit.
The following options for editing a user are available:

MAP Control Center Operation | en 19
Bosch Security Systems B.V. User manual 2019-11 | 08 | F.01U.168.328
–Reset Passcode
–Edit User Name
–Edit Smartkey User
–Edit Control Center User
How to reset a passcode
1. Press Reset Passcode.
2. A confirmation message is displayed.
PThe passcode of the selected user is reset to the default value.
The default passcode is a combination of the 3-digit user ID and a 6-digit password. The
6-digit password default value is 000000. The 3-digit user ID cannot be changed.
PA new password has to be entered. For more information, refer to Changing passcode,
page 20.
How to edit a user name
1. Press Edit User Name.
The user name options are displayed.
2. To enter the first name of the user, press Enter User First Name.
3. Use the alphanumeric keypad to enter the name.
4. Press Enter.
5. To enter the last name of the user, press Enter User Last Name.
6. Use the alphanumeric keypad to enter the name.
7. Press Enter.
8. To confirm the first and last name, press .
The user options are displayed.
Optional: Smartkey users
Notice!
This option can only be used if a smartkey profile is configured by the installer.
4For more information, contact your installer or system administrator.
How to edit a smartkey user
1. Press Edit Smartkey User.
The smartkey options are displayed.
2. To enter the ID of the smartkey token, press Enter Smartkey Token Number.
3. Use the alphanumeric keypad to enter the 8-character ID found on the smartkey token in
the Enter field.
4. To confirm, press .
5. To verify, use the alphanumeric keypad to enter the 8-character ID found on the smartkey
token in the Verify Code field.
6. To confirm the ID, press .
The smartkey options are displayed.
7. Press Select Smartkey Profile.
The predefined smartkey profiles are displayed. If no predefined smartkey profile is
available, an error message is displayed.
8. Select a predefined smartkey profile.

20 en | Operation MAP Control Center
2019-11 | 08 | F.01U.168.328 User manual Bosch Security Systems B.V.
9. To confirm, press .
The user options are displayed.
How to edit a control center user
1. Press Edit Control Center User.
The control center options are displayed.
2. Press Select User Type.
3. Choose between Standard User and Temporary User.
The icon indicates the selection.
4. In case of a temporary user, enter the number of days for which the user is activated (0 -
99).
If you enter 0, the temporary user will be an inactive user. Inactive users can be activated
by the installer.
5. To confirm the temporary user duration, press .
6. To confirm the user type, press .
The control center user options are displayed.
7. Press Select User Profile.
8. Choose between Installer Profile, Owner/Facility Manager, Standard User and Super
User.
The icon indicates the selection.
9. To confirm the user profile, press .
The control center user options are displayed.
10. Press Select User Language.
11. Choose between one of the displayed languages.
The icon indicates the selection.
12. To confirm the user language, press .
The control center user options are displayed.
13. Press Select Exit Delay.
14. Choose between Standard and Extended.
The icon indicates the selection.
15. To confirm the exit delay option, press .
The control center user options are displayed.
16. To confirm the control center user options, press .
The user options are displayed.
How to finish editing a user
4After all control center user options are entered, press to update the user.
A confirmation message is displayed.
The Users menu is displayed.
PThe user has been edited.
5.5.4 Changing passcode
The user passcode is a combination of the 3-digit user ID and a 6-digit password. The 3-digit
user ID cannot be changed.