Bosch GLM100-23 Assembly instructions

IMPORTANT: IMPORTANT: IMPORTANTE:
Read Before Using Lire avant usage Leer antes de usar
Operating/Safety Instructions
Consignes d’utilisation/de sécurité
Instrucciones de funcionamiento
y seguridad
1-877-BOSCH99 (1-877-267-2499) www.boschtools.com
For English Version Version française Versión en español
See page 4 Voir page 23 Ver la página 43
GLM100-23
Call Toll Free for Consumer Information & Service Locations
Pour obtenir des informations et les adresses de nos centers de
service après-vente, appelez ce numéro gratuit
Llame gratis para obtener información para el consumidor y
ubicaciones de servicio
160992A6EZ GLM100-23 202210.indd 1 10/4/22 10:19 AM

-2-
4
5
6
7
8
3
1
2
9
e
f
g
h
i
10
abc
d
160992A6EZ GLM100-23 202210.indd 2 10/4/22 10:19 AM

-3-
1’ 6” (0.5m)
1’ 6” (0.5m)
8’ (2.45m)
1’ 6” (0.5m)
160992A6EZ GLM100-23 202210.indd 3 10/4/22 10:19 AM

-4-
General Safety Rules
Read all instructions. Failure to
follow all instructions listedbelow
may result in hazardous radiation exposure, electric
shock, fire and/or serious injury. The term “tool” in the
warnings listed belowrefers toyour mains-operated(corded)
tool or battery-operated (cordless) tool.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The following label is
on your laser tool for
your safety. ALWAYS BE
AWARE of their location
when using the tool.
Safety Symbols
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
!
This is the safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
Read manual symbol - Alerts user to read
manual.
WARNING indicates a hazardous
situation which, if not avoided, will result in death or
serious injury.
160992A6EZ GLM100-23 202210.indd 4 10/4/22 10:19 AM

-5-
Working safely with the measuring tool is possible only when
the operating and safety information are read completely and
the instructions contained therin are strictly followed. Never
make warning labels on the Measuring tool unrecognizable.
Never aim the beam at a workpiece with a reflective surface.
Bright shiny reflective sheet steel or similar reflective surfaces
are not recommended for laser use. Reflective surfaces could
direct the beam back towards the operator.
Take care to recognize the accuracy and range of the device.
Measurement may not be accurate if used beyond the rated range
of the device.
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
The use of optical instruments with this product will increase
eye hazards.
Do not point the laser beam at persons or animals and do not
look intothe laserbeam yourself, not even from alarge distance.
General Safety Rules
DO NOT direct the laser beam at persons or
animalsanddo notstareintothelaserbeam
yourself. This laser measure produces
class 2 laser radiation and complies with
21 CFR 1040.10 and 1040.11 except for
conformance with IEC 60825-1 Ed. 3., as described in
Laser Notice No. 56, dated May 8, 2019.” This can lead to
persons being blinded.
Safety Rules
160992A6EZ GLM100-23 202210.indd 5 10/4/22 10:19 AM

-6-
Do not use the laser viewing glasses as safety goggles. The laser
viewing glasses are used for improved visualization of the laser
beam, but they do not protect against laser radiation.
Do not use the laser viewing glasses as sun glasses or in traffic.
The laser viewing glasses do not afford complete UV protection and
reduce color perception.
ALWAYS: Make sure that any bystanders in the vicinity of use
are made aware of the dangers of looking directly into the
measuring tool.
DO NOT remove or deface any warning or caution labels.
Removing labels increases the risk of exposure to laser
radiation.
DO NOT stare directly at the laser beam or project the laser
beam directly into the eyes of others. Serious eye injury could
result.
DO NOT place the measuring tool in a position that may
cause anyone to stare into the laser beam intentionally or
unintentionally. Serious eye injury could result.
DO NOT use any optical tools such as, but not limited to,
telescopes or transits to view the laser beam. Serious eye injury
could result.
ALWAYS remove the batteries when cleaning the laser light
aperture to laser lens.
DO NOT operate the measuring tool around children or allow
children to operate the measuring tool. Serious eye injury could
result.
ALWAYS turn the measuring tool “OFF” when not in use.
Leaving the measuring tool “ON” increases the risk of someone
inadvertently staring into the laser beam.
Safe Operating Procedures
160992A6EZ GLM100-23 202210.indd 6 10/4/22 10:19 AM

-7-
DO NOT operate the measuring tool in combustible areas such
as in the presence of flammable liquids, gases or dust.
ALWAYS position the measuring tool securely. Damage to the
measuring tool and/or serious injury to the user could result if the
measuring tool falls.
ALWAYS use only the accessories that are recommended by
the manufacturer of your measuring tool. Use of accessories
that have been designed for use with other measuring tools could
result in serious injury.
DO NOT leave measuring tool “on” unattended in any
operation mode.
Repair and servicing must always be performed by a qualified
repair facility. Repairs performed by unqualified personnel could
result in serious injury.
DO NOT use this measuring tool for any purpose other than
those outlined in this manual. This could result in serious injury.
DO NOT disassemble the measuring tool. There are no user
serviceable parts inside. Disassembling the laser will void all
warranties on the product. Do not modify the product in any
way. Modifying the measuring tool may result in hazardous laser
radiation exposure.
Electrical safety
Batteries can explode or leak, cause injury or fire. To reduce
this risk, always follow all instructions and warnings on the
battery label and package.
DO NOT short any battery terminals.
DO NOT charge alkaline batteries.
DO NOT mix old and new batteries. Replace all of them at the
same time with new batteries of the same brand and type.
DO NOT mix battery chemistries.
Dispose of or recycle batteries per local code.
DO NOT dispose of batteries in fire.
Keep batteries out of reach of children.
Remove batteries if the device will not be used for several
months.
160992A6EZ GLM100-23 202210.indd 7 10/4/22 10:19 AM

-8-
The manufacturer is not responsible for radio
interference caused by unauthorized modifica-
tions to this equipment. Such modifications
could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1) This device may not cause harmful interfer-
ence, and
2) This device must accept any interference
received, including interference that may
cause undesired operation.
NOTE! This equipment has been tested and
found to comply with the limits for a Class
B digital devices, pursuant to Part 15 of the
FCC rules. These limits are designed to pro-
vide reasonable protection against harmful
interference in a residential installation. This
equipment generates uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio com-
munications. However, there is no guarantee
that interference will not occur in a particu-
lar installation. If this equipment does cause
harmful interference to radio or television re-
ception, which can be determined by turning
the equipment off and on, the user is encour-
aged to try to correct the interference by one
or more of the following measures:
•Reorientorrelocatethereceivingantenna.
FCC Caution
160992A6EZ GLM100-23 202210.indd 8 10/4/22 10:19 AM

-9-
•Increasetheseparationbetweentheequip-
ment and receiver.
•Connect the equipment into an outlet on a
circuit different from that to which the re-
ceiver is connected.
•Consultthedealeroranexperiencedradio/
TV technician for help.
IC Canada
This class B digita device complies with ICES-003
CanadaICES-003(B)/NMB-003(B)
160992A6EZ GLM100-23 202210.indd 9 10/4/22 10:19 AM

-10-
Features
The numbering of the product features shown refers to the
illustration of the measuring tool on the graphic page.
1On/Off
(Measuring button)
2Display
3Battery lid
4Latch of battery lid
5Serial number
6Laser warning label
7Reception lens
8Laser beam outlet
9Rounding button
10 Rear edge
Display Elements
aBattery status indicator
bLaser on indicator
cFractional rounding
dCurrent measuring value
eProduct name
fProduct information
gManual QR code
hFactory reset
iLegal notes
The measuring tool is intended for measuring distances,
lengths, heights and clearances. The measuring tool is
suitable for measuring only indoors.
Intended Use
160992A6EZ GLM100-23 202210.indd 10 10/4/22 10:19 AM