Bosch DIVAR IP 3000 DIP-3040-00N User manual

DIVARIP3000
DIP-3040-00N,DIP-3042-2HD,DIP-3042-4HD
en InstallationManual

DIVARIP3000 TableofContents|en 3
BoschSicherheitssystemGmbH InstallationManual 2014.11|V5|DOC
TableofContents
1Safetyprecautions 4
1.1 Generalsafetyprecautions 4
1.2 Electricalsafetyprecautions 5
1.3 ESDprecautions 6
1.4 Operatingprecautions 6
2Systemoverview 7
2.1 Chassisfeatures 7
2.2 Chassiscomponents 7
2.2.1 Chassis 7
2.2.2 Backplane 7
2.2.3 Powersupply 7
2.3 Deviceviews 8
2.3.1 LEDdescription-frontpanel 9
2.3.2 LANportLEDdescription-rearpanel 10
3Chassissetupandmaintenance 11
3.1 Removingharddrivetrays 11
3.2 Installingaharddrive 11
4Systemsetup-firststeps 12
4.1 Introduction 12
4.2 Setupinstruction 12
4.3 Startingtheapplication 12
4.4 UsingBoschVMSConfigWizard 13
4.5 Addingadditionallicenses 14
4.6 UsingBoschVMSOperatorClient 14
5Connectingtotheinternet 16
5.1 Protectingthesystemfromunauthorizedaccess 16
5.2 Settingupportforwarding 16
5.3 Choosinganappropriateclient 16
5.3.1 RemoteconnectionwithOperatorClient 16
5.3.2 RemoteconnectionwithVideoSecurityApp 16
5.4 InstallinganEnterpriseManagementServer 17
6Recoveringtheunit 18
7AdditionalDocumentationandclientsoftware 19

4en|Safetyprecautions DIVARIP3000
2014.11|V5|DOC InstallationManual BoschSicherheitssystemGmbH
1 Safetyprecautions
Observethesafetyprecautionsinthischapter.
1.1 Generalsafetyprecautions
Followtheserulestoensuregeneralsafety:
– Keeptheareaaroundthesystemcleanandfreeofclutter.
– Placethechassistopcoverandanysystemcomponentsthathavebeenremovedaway
fromthesystemoronatablesothattheywon'taccidentallybesteppedon.
– Whileworkingonthesystem,donotwearlooseclothingsuchasnecktiesand
unbuttonedshirtsleeves,whichcancomeintocontactwithelectricalcircuitsorbe
pulledintoacoolingfan.
– Removeanyjewelryormetalobjectsfromyourbody,whichareexcellentmetal
conductorsthatcancreateshortcircuitsandharmyouiftheycomeintocontactwith
printedcircuitboardsorareaswherepowerispresent.
!
Warning!
Interruptionofmainssupply:
Voltageisappliedassoonasthemainsplugisinsertedintothemainssocket.
However,fordeviceswithamainsswitch,thedeviceisonlyreadyforoperationwhenthe
mainsswitch(ON/OFF)isintheONposition.Whenthemainsplugispulledoutofthe
socket,thesupplyofpowertothedeviceiscompletelyinterrupted.
!
Warning!
Removingthehousing:
Toavoidelectricshock,thehousingmustonlyberemovedbyqualifiedservicepersonnel.
Beforeremovingthehousing,theplugmustalwaysberemovedfromthemainssocketand
remaindisconnectedwhilethehousingisremoved.Servicingmustonlybecarriedoutby
qualifiedservicepersonnel.Theusermustnotcarryoutanyrepairs.
!
Warning!
PowercableandACadapter:
Wheninstallingtheproduct,usetheprovidedordesignatedconnectioncables,powercables
andACadaptors.Usinganyothercablesandadaptorscouldcauseamalfunctionorafire.
ElectricalApplianceandMaterialSafetyLawprohibitstheuseofULorCSA-certifiedcables
(thathaveUL/CSAshownonthecode)foranyotherelectricaldevices.
!
Warning!
Lithiumbattery:
Batteriesthathavebeeninsertedwronglycancauseanexplosion.Alwaysreplaceempty
batterieswithbatteriesofthesametypeorasimilartyperecommendedbythemanufacturer.
Handleusedbatteriescarefully.Donotdamagethebatteryinanyway.Adamagedbattery
mayreleasehazardousmaterialsintotheenvironment.
Disposeofemptybatteriesaccordingtothemanufacturer'sinstructions.
!
Warning!
Handlingofleadsoldermaterialsusedinthisproductmayexposeyoutolead,achemical
knowntotheStateofCaliforniatocausebirthdefectsandotherreproductiveharm.

DIVARIP3000 Safetyprecautions|en 5
BoschSicherheitssystemGmbH InstallationManual 2014.11|V5|DOC
Notice!
Electrostaticallysensitivedevice:
Toavoidelectrostaticdischarges,theCMOS/MOSFETprotectionmeasuresmustbecarried
outcorrectly.
Whenhandlingelectrostaticallysensitiveprintedcircuits,groundedanti-staticwristbands
mustbewornandtheESDsafetyprecautionsobserved.
Notice!
Installationshouldonlybecarriedoutbyqualifiedcustomerservicepersonnelinaccordance
withtheapplicableelectricalregulations.
Disposal
YourBoschproducthasbeendevelopedandmanufacturedusinghigh-
qualitymaterialsandcomponentsthatcanbereused.
Thissymbolmeansthatelectronicandelectricaldevicesthathavereached
theendoftheirworkinglifemustbedisposedofseparatelyfrom
householdwaste.
IntheEU,separatecollectingsystemsarealreadyinplaceforused
electricalandelectronicproducts.Pleasedisposeofthesedevicesatyour
localcommunalwastecollectionpointoratarecyclingcenter.
1.2 Electricalsafetyprecautions
Basicelectricalsafetyprecautionsshouldbefollowedtoprotectyoufromharmandthe
systemfromdamage:
– Beawareofthelocationsofthepoweron/offswitchonthechassisaswellastheroom's
emergencypower-offswitch,disconnectionswitchorelectricaloutlet.Ifanelectrical
accidentoccurs,youcanthenquicklyremovepowerfromthesystem.
– Donotworkalonewhenworkingwithhighvoltagecomponents.
– Powershouldalwaysbedisconnectedfromthesystemwhenremovingorinstallingmain
systemcomponents,suchasthemotherboardormemorymodules.Whendisconnecting
power,youshouldfirstturnoffthesystemandthenunplugthepowercordsfromallthe
powersupplymodulesinthesystem.
– Whenworkingaroundexposedelectricalcircuits,anotherpersonwhoisfamiliarwiththe
power-offcontrolsshouldbenearbytoswitchoffthepowerifnecessary.
– Useonlyonehandwhenworkingwithpowered-onelectricalequipment.Thisistoavoid
makingacompletecircuit,whichwillcauseelectricalshock.Useextremecautionwhen
usingmetaltools,whichcaneasilydamageanyelectricalcomponentsorcircuitboards
theycomeintocontactwith.
– Thepowersupplypowercordsmustincludeagroundingplugandmustbepluggedinto
groundedelectricaloutlets.Theunithasmorethanonepowersupplycord.Disconnect
bothpowersupplycordsbeforeservicingtoavoidelectricalshock.
– Mainboardreplaceablesoldered-infuses:Self-resettingPTC(PositiveTemperature
Coefficient)fusesonthemainboardmustbereplacedbytrainedservicetechniciansonly.
Thenewfusemustbethesameorequivalentastheonereplaced.Contacttechnical
supportfordetailsandsupport.

6en|Safetyprecautions DIVARIP3000
2014.11|V5|DOC InstallationManual BoschSicherheitssystemGmbH
!
Caution!
MainboardBattery:Thereisadangerofexplosioniftheonboardbatteryisinstalledupside
down,whichwillreverseitspolarities.Thisbatterymustbereplacedonlywiththesameor
anequivalenttyperecommendedbythemanufacturer(CR2032).Disposeofusedbatteries
accordingtothemanufacturer'sinstructions.
1.3 ESDprecautions
ElectrostaticDischarge(ESD)isgeneratedbytwoobjectswithdifferentelectricalcharges
comingintocontactwitheachother.Anelectricaldischargeiscreatedtoneutralizethis
difference,whichcandamageelectroniccomponentsandprintedcircuitboards.The
followingmeasuresaregenerallysufficienttoneutralizethisdifferencebeforecontactismade
toprotectyourequipmentfromESD:
– Donotusematsdesignedtodecreaseelectrostaticdischargeasprotectionfrom
electricalshock.Instead,userubbermatsthathavebeenspecificallydesignedas
electricalinsulators.
– Useagroundedwriststrapdesignedtopreventstaticdischarge.
– Keepallcomponentsandprintedcircuitboards(PCBs)intheirantistaticbagsuntilready
foruse.
– Touchagroundedmetalobjectbeforeremovingtheboardfromtheantistaticbag.
– Donotletcomponentsorprintedcircuitboardscomeintocontactwithyourclothing,
whichmayretainachargeevenifyouarewearingawriststrap.
– Handleaboardbyitsedgesonly.Donottouchitscomponents,peripheralchips,memory
modulesorcontacts.
– Whenhandlingchipsormodules,avoidtouchingtheirpins.
– Putthemainboardandperipheralsbackintotheirantistaticbagswhennotinuse.
– Forgroundingpurposes,makesureyourcomputerchassisprovidesexcellent
conductivitybetweenthepowersupply,thecase,themountingfastenersandthe
mainboard.
1.4 Operatingprecautions
Thechassiscovermustbeinplacewhenthesystemisoperatingtoassurepropercooling.Out
ofwarrantydamagetothesystemcanoccurifthispracticeisnotstrictlyfollowed.
Note:
Pleasehandleusedbatteriescarefully.Donotdamagethebatteryinanyway.Adamaged
batterymayreleasehazardousmaterialsintotheenvironment.Donotdiscardausedbattery
inthegarbageorapubliclandfill.Pleasecomplywiththeregulationssetupbyyourlocal
hazardouswastemanagementagencytodisposeofyourusedbatteryproperly.

DIVARIP3000 Systemoverview|en 7
BoschSicherheitssystemGmbH InstallationManual 2014.11|V5|DOC
2 Systemoverview
TheDIVARIP3000systemisanaffordableandeasytouseall-in-onerecording,viewing,and
managementsolutionfornetworksurveillancesystemsofupto32channels.Allchannelsare
pre-licensed.RunningthefullBoschVMSsolutionandpoweredbyBoschVRM(Video
RecordingManager)includingtheVideoStreamingGatewaytointegrate3rdpartycameras,
DIVARIP3000isanintelligentIPstoragedevicethateliminatestheneedforseparateNVR
(NetworkVideoRecorder)serverandstoragehardware.
DIVARIP3000isa4-bayminitowerunitthatcombinesadvancedmanagementandstate-of-
the-artrecordingmanagementintoasinglecost-effective,plugandplayIPrecordingappliance
forIT-mindedcustomerswhichareseekingforastate-of-the-art“secondgeneration”DVRand
NVRrecordingsolution.
Easytoinstallandoperate,DIVARIP3000featureswizard-basedset-upandcentralized
configurationtoreduceinstallationtimes.Allcomponentsarepre-installedandpre-
configured.Simplyconnecttothenetworkandturnontheunit—DIVARIP3000isreadyto
beginrecordingstraightoutofthebox.
BoschVideoManagementSystemmanagesallIPanddigitalvideoandaudio,plusallthe
securitydatabeingtransmittedacrossyourIPnetwork.ItseamlesslycombinesIPcameras
andencoders,providessystem-wideeventandalarmmanagement,systemhealthmonitoring,
userandprioritymanagement.
DIVARIP3000featuresfront-swappableSATA-IIharddrives.Allsystemsoftwareispre-
installedandpre-activated—creatinganout-of-the-boxready-to-usevideomanagement
appliance.DIVARIP3000utilizesWindowsStorageServer2008R2operatingsystem.
2.1 Chassisfeatures
Thechassisincludesthefollowingfeatures:
– CPU(Inteli3processor)
– 4slotsforSATAdrives(frontreplaceable)
– 1xVGAoutput(onboard)
– 1xDVIgraphicsoutput
– 4xUSB2.0,1xUSB3.0
– 1xinternalUSBTranscoderdevice
– 1xGigabitEthernetLANport
2.2 Chassiscomponents
Thischapterdescribesthemostcommoncomponentsincludedwithyourchassis.
2.2.1 Chassis
Thechassisincludes4slotsforharddrives.
2.2.2 Backplane
Thebackplaneacceptsfront-swappableSATA-IIharddrives.
!
Warning!
Usecautionwhenservicingandworkingaroundthebackplane.Hazardousvoltageorenergy
ispresentonthebackplanewhenthesystemisoperating.Donottouchthebackplanewith
anymetalobjectsandmakesurenoribboncablestouchthebackplane.
2.2.3 Powersupply
Thechassisfeaturesahighlyenergy-efficientpowersupplies.

8en|Systemoverview DIVARIP3000
2014.11|V5|DOC InstallationManual BoschSicherheitssystemGmbH
2.3 Deviceviews
ThereareseveralLEDsonthefrontandrearofthechassis.TheLEDsshowtheover-allstatus
ofthesystemandtheactivityandhealthofspecificcomponents.
Frontview:
1
52 3 4
6
1Lockforfrontcover 4LANactivityLED
2Poweron/offLED 5SystemstatusLED
3HarddiskaccessLED 6IndividualharddiskLED

DIVARIP3000 Systemoverview|en 9
BoschSicherheitssystemGmbH InstallationManual 2014.11|V5|DOC
Rearview:
16
2 3 4 5 7
11xVGA(monitor) 5Mainsconnection100-240VAC
21xEthernet(RJ45) 61xUSB3.0
Note:Donotusethisportfor
keyboardandmouse.
34xUSB2.0
Note:Usetheseportsforkeyboard
andmouseconnection.
71xDVI(monitor),forlocalviewing
Note:
Ifthesystemisonlyconnectedtothe
DVIport,novideosignalisdisplayed
untilthesystemhasstarted
completely.Thiscantake1–2
minutes.Avideosignalisalways
displayedwhenthemonitoris
connectedtotheVGAport.
41xeSATAfordataexport
Note:Donotconnectharddiskdrives
forrecording.
2.3.1 LEDdescription-frontpanel
ThischapterdescribestheLEDdisplaysonthefrontofthechassis.
LEDindicator LEDcolor LEDstate Description
PowerLED N/A Off Poweroff
Blue On(default) Working(S0state)

10 en|Systemoverview DIVARIP3000
2014.11|V5|DOC InstallationManual BoschSicherheitssystemGmbH
LEDindicator LEDcolor LEDstate Description
HDDLED N/A Off Nodiskaccess
Blue Blinking Diskaccess
LANLED N/A Off Networkdisconnected
Blue On Networkconnected
Blue Blinking Networkactivity
SystemLED N/A Off Poweroff
Blue On(default) Systemhasbootedinnormaloperation.
Blue Blinking Systemisbootingorshuttingdown
Red On Criticaleventoccurred,suchasdegraded
RAIDvolume.
BoschalsoprovidestheAPIandthen
applicationprogramisabletocontrolthis
status.
Individualhard
diskLED
N/A Off(default) Harddrivenotpresent.
Blue On Harddrivepresent.
Red On BoschprovidestheAPItoletapplication
programtocontrolthisstatus.
2.3.2 LANportLEDdescription-rearpanel
ThischapterdescribestheLANportLEDontherearofthechassis.
LANconnector:
12
Nr. LEDindicator LEDcolor LEDstate NICstate
1RJ45LED
(left)
N/A Off Noconnectionor10Mb/s
Green On 100Mb/s
Yellow On 1000Mb/s
2RJ45LED
(right)
Yellow On Activeconnection
Yellow Blinking Transmitorreceiveactivity

DIVARIP3000 Chassissetupandmaintenance|en 11
BoschSicherheitssystemGmbH InstallationManual 2014.11|V5|DOC
3 Chassissetupandmaintenance
Thischaptercoversthestepsrequiredtoinstallcomponentsandperformmaintenanceonthe
chassis.
!
Caution!
Reviewthewarningsandprecautionslistedinthemanualbeforesettinguporservicingthis
chassis.
Seealso:
Safetyprecautions,page4
3.1 Removingharddrivetrays
Thedrivesaremountedindrivecarrierstosimplifytheirinstallationandremovalfromthe
chassis.Thesecarriersalsohelppromoteproperairflowforthedrivebays.
Toremoveharddrivetraysfromthechassis:
1. Turnoffthesystem.
2. Pressthereleasebuttononthedrivecarrier.Thisextendsthedrivecarrierhandle.
3. Usethehandletopullthedrivecarrierwiththedriveoutofthechassis.
4. Insertthedrivecarrierwiththenewdriveintothechassisbay,makingsurethatthedrive
carrierhandleiscompletelyclosed.
Notice!
Exceptforshortperiodsoftime,donotoperatetheunitwiththeharddrivesremovedfrom
thebays.
3.2 Installingaharddrive
Thedrivesaremountedindrivecarriers.
Toinstallaharddrivetotheharddrivecarrier:
1. Removethedrivefromthecarrier.
2. Installanewdriveintothecarrierwiththeprintedcircuitboardsidefacingdownsothat
themountingholesalignwiththoseinthecarrier.
3. Replacethedrivecarrierintothechassisbay,makingsurethatthedrivecarrierhandleis
completelyclosed.
Notice!
WerecommendusingtherespectiveBoschharddiskdrives.Theharddiskdrivesasoneof
thecriticalcomponentarecarefullyselectedbyBoschbasedonavailablefailurerates.HDD–
notdeliveredfromBosch–arenotsupported.InformationonsupportedHDDscanbefound
inthedatasheetintheBoschOnlineProductCatalog.

12 en|Systemsetup-firststeps DIVARIP3000
2014.11|V5|DOC InstallationManual BoschSicherheitssystemGmbH
4 Systemsetup-firststeps
ThefollowinginstallationdirectiveprovidesinformationonInstallationandConfiguration.
ThischapterisvalidforDIVARIPmodelsthatcomewithpre-installedharddrives.Emptyunits
startintotheDOMrecoverymenuonfirststart.
Seealso:
–Recoveringtheunit,page18
4.1 Introduction
DIVARIPsystemsareshippedwithapre-installedConfigurationWizardfromfactory.
4.2 Setupinstruction
AllDIVARIPsystemsarepreconfiguredwithadefaultIPaddressandwithdefaultiSCSI
settings.
– IPAddress:192.168.0.200
– Subnetmask:255.255.255.0
Observethefollowing:
– DIVARIPneedstohaveanactivenetworklinkduringinstallation.Makesurethatthe
networkswitchyouareconnectingtoispoweredon.
– ThedefaultIPaddressmustnotbeoccupiedbyanyotherdeviceinthenetwork.Make
surethatthedefaultIPaddressesofexistingDIVARIPsystemsinthenetworkare
changedbeforeaddinganotherDIVARIP.
– DeterminewhethertheinitialinstallationisonaDHCPnetwork.Ifnotthenyoumust
assignvalidIPaddressestothevideodevices.ConsultthelocalITadministratortoobtain
avalidIPaddressrangetobeusedwithDIVARIPandassociateddevices.
– ThedefaultiSCSIsettingsareoptimizedforusewithVRM.
Userwithadministratorrights:
– User:BVRAdmin
– Password:WSS4Bosch
Notice!
Westronglyrecommendnotchangingtheusersettings.Changingtheusersettingscanresult
inmalfunctioningofthesystem.
4.3 Startingtheapplication
DIVARIPsystemisreadytogooutofthebox.Theapplicationprovidesasimpletoinstalland
intuitivetousesolutionfornetworksurveillancesystems.
Notice!
InordertostarttheapplicationforthefirsttimeyoumustusetheVGAport.Ifthesystemis
onlyconnectedtotheDVIport,novideosignalisdisplayeduntilthesystemhasstarted
completely.Thiscantake1–2minutes.Avideosignalisalwaysdisplayedwhenthemonitor
isconnectedtotheVGAport.
Tostarttheapplication:
1. Connecttheunitandthecamerastothenetwork.
2. Turnontheunit.
TheWindowsStorageServer2008R2setupprocessstarts.
3. Selecttheappropriatelanguagefortheinstallation,thenclickNext.

DIVARIP3000 Systemsetup-firststeps|en 13
BoschSicherheitssystemGmbH InstallationManual 2014.11|V5|DOC
4. IntheCountryorregion,TimeandcurrencyandKeyboardlayoutlists,clickthe
appropriateitem,thenclickNext.
TheMicrosoftSoftwareLicenseTermsandtheEULA(EndUserLicenseAgreement)are
displayed.
5. Acceptthelicenseterms,thenclickStart.Windowsrestarts.
Afterrestartisfinished,differentBoschVMSversionsaredisplayedonthescreen.
6. Double-clicktheBoschVMSversionyouwanttoinstall.
Note.Werecommendthatyouinstallthelatestversion.
Theinstallationcantakeseveralminutes.Donotturnoffthecomputer.Ifnecessary,
restartthesystem.
7. Afterrestartisfinished,pressCTR+ALT+DELETE.TheWindowslogonpageisdisplayed.
8. EnterthedefaultpasswordWSS4Bosch.
9. Afterenteringthepassword,amessageisdisplayedthatyoumustchangethepassword
beforeloggingonthefirsttime.Toconfirm,clickOK.
10. Changethepassword.
Aseriesofscriptsperformimportantsetuptasks.Thiscantakeseveralminutes.Donot
turnoffthecomputer.
TheBoschVMSdefaultscreenisdisplayed.
Note:Incaseofpasswordlossasystemrecoverymustbeperformedasdescribedinthe
installationmanual.Theconfigurationmustbedonefromscratchormustbeimported.
11. OntheBoschVMSdefaultscreen,double-clicktheBoschVMSWizardicon tostart
theConfigurationWizard.
TheWelcomepageisdisplayed.
12. ConfigurethesystemusingtheConfigurationWizard.
Notice!
Toperformadministrativetasks,theBVRAdminaccountcanbeenteredwhenBoschVMS
defaultscreenisdisplayed.Todoso,pressCTRL+ALT+DEL,thenholddownSHIFTwhile
clickingtheSwitchUseroptionandkeepSHIFTpressedforaboutfiveseconds.
Notice!
Westronglyrecommendnotchanginganyoperatingsystemsettings.Changingoperating
systemsettingscanresultinmalfunctioningofthesystem.
Seealso:
–UsingBoschVMSConfigWizard,page13
–Addingadditionallicenses,page14
–Recoveringtheunit,page18
4.4 UsingBoschVMSConfigWizard
IntendeduseforConfigWizardisthequickandeasyconfigurationofasmallersystem.Config
WizardhelpsyoutoachieveaconfiguredsystemincludingVRM,iSCSIsystem,cameras,
recordingprofilesandusergroups.
Usergroupsandtheirpermissionsareconfiguredautomatically.Youcanaddorremoveusers
andsetpasswords.
ConfigWizardcanaccessManagementServeronlyonthelocalcomputer.
Youcansaveanactivatedconfigurationforbackuppurposesandimportthisconfiguration
later.Youcanchangethisimportedconfigurationafterimport.
ConfigWizardaddsthelocalVRMautomatically.

14 en|Systemsetup-firststeps DIVARIP3000
2014.11|V5|DOC InstallationManual BoschSicherheitssystemGmbH
Restrictions:
ThefollowingtaskscannotbedonewiththeConfigurationWizard.UseBoschVMS
ConfigurationClientinstead.
– addingadditionallicensepackages
– adjustingschedules
– configuringsystemswithnoormultipleVRM
– configuringexternalstoragedevices
– addingVideoStreamingGateway
– alladvancedconfigurationsbeyondabasicsetup(mapsoralarms,forexample)
ToachieveaquickconfigurationusingtheConfigurationWizard:
1. OntheBoschVMSdefaultscreen,double-clicktheBoschVMSWizardicon.The
Welcomepageisdisplayed.
2. Followthewizardandobservetheinstructionsonthescreen.
Notice!
ForthetasksthatcannotbedonewithConfigurationWizard,andfordetailedinformation
concerningConfigurationWizarditself,refertotheBoschVMSmanual(seeAdditional
Documentationandclientsoftware,page19).
4.5 Addingadditionallicenses
YoucanaddadditionallicensesusingConfigurationClient.
Toactivatethesoftware:
1. StartConfigurationClient.
2. OntheToolsmenu,clickLicenseManager....
TheLicenseManagerdialogboxisdisplayed.
3. Clicktochecktheboxesforthesoftwarepackage,thefeatures,andtheexpansionsthat
youwanttoactivate.Fortheexpansions,enterthenumberoflicenses.
IfyouhavereceivedaBundleInformationfile,clickImportBundleInfotoimportit.
4. ClickActivate.
TheLicenseActivationdialogboxisdisplayed.
5. Writedownthecomputersignatureorcopyandpasteitintoatextfile.
6. OnacomputerwithInternetaccess,enterthefollowingURLintoyourbrowser:
https://activation.boschsecurity.com
IfyoudonothaveanaccounttoaccesstheBoschLicenseActivationCenter,either
createanewaccount(recommended)orclickthelinktoactivateanewlicensewithout
loggingon.Ifyoucreateanaccountandlogonbeforeactivating,theLicenseManager
keepstrackofyouractivations.Youcanthenreviewthisatanytime.
FollowtheinstructionstoobtaintheLicenseActivationKey.
7. ReturntotheBoschVMSsoftware.IntheLicenseActivationdialogbox,typetheLicense
ActivationKeyobtainedfromtheLicenseManagerandclickActivate.
Thesoftwarepackageisactivated.
4.6 UsingBoschVMSOperatorClient
UseBoschVMSOperatorClienttoverifythelive,recordingandplaybackfunctionalityof
DIVARIP.
ToverifyliveimagefunctionalityintheOperatorClient
1. OntheBoschVMSdefaultscreen,double-clicktheOperatorClienticon .The
applicationstarts.

DIVARIP3000 Systemsetup-firststeps|en 15
BoschSicherheitssystemGmbH InstallationManual 2014.11|V5|DOC
2. EnterthefollowingandclickOK.
Username:admin
Password:nopasswordrequired(ifnotsetwiththewizard)
Connection:127.0.0.1
3. Clicktheliveimageicon.TheLogicalTreewiththecamerasisdisplayed.
4. Selectacameraanddragittoanimagewindow.Theimageofthecameraisdisplayedif
thecameraisassignedcorrectly.
Note:
Camerasintheimagewindowwithareddotinthecamera’siconareviewedlive.
ToverifyrecordingfunctionalityintheOperatorClient
4CamerasintheLogicalTreewithareddotinthecamera’siconarerecording.
ToverifyplaybackfunctionalityintheOperatorClient
4Thetimelinemovesiftheacameraisviewedinplaybackmode.
Performanceoverviewlive:
4CIF
2.5Mbit 5Mbit 10Mbit
Numberofsoftwaremonitors 17 13 8
720p
2.5Mbit 5Mbit 10Mbit
Numberofsoftwaremonitors 12 10 5
1080p
2.5Mbit 5Mbit 10Mbit
Numberofsoftwaremonitors 6 5 3
ToperformfurtherfunctionalitiesrefertotheBoschVMSmanual.Referencestothemanual
aredescribedinAdditionalDocumentationandclientsoftware,page19.

16 en|Connectingtotheinternet DIVARIP3000
2014.11|V5|DOC InstallationManual BoschSicherheitssystemGmbH
5 Connectingtotheinternet
ThissectiondescribesthestepsthatarerequiredtoaccesstheDIVARIPsystemfromthe
internet.
5.1 Protectingthesystemfromunauthorizedaccess
Inordertoprotectthesystemfromunauthorizedaccess,werecommendthatyoufollow
strongpasswordrulesbeforeconnectingthesystemtotheinternet.Thestrongeryour
password,themoreprotectedyoursystemwillbefromunauthorizedpersonsandmalware.
5.2 Settingupportforwarding
InordertoaccessaDIVARIPsystemfromtheinternetthroughaNAT/PATcapablerouter,port
forwardingmustbeconfiguredontheDIVARIPsystemandontherouter.
Tosetupportforwarding:
1. Makesurethesystemisfullyconfiguredwithalldevices.
2. OntheBoschVMSdefaultscreen,double-clicktheBoschVMSWizardicon.The
Welcomepageisdisplayed.
3. FollowthewizarduntiltheBasicpageisdisplayed.
4. UnderPortMapping,selecttheEnablePortMappingcheckbox.
5. SpecifythepublicIPadressortheDNSnameofyourinternetconnection.
6. FollowthewizarduntiltheFinishpageisdisplayed,thenclickDetails.
7. NotetheportrulesdisplayedinthePortMappingTableorexportthetabletoaUSB
drive.
8. Entertheseportrulesintheportforwardingsettingsofyourinternetrouter.
TheDIVARIPsystemisnowaccessiblefromtheInternet.
5.3 Choosinganappropriateclient
TherearetwosupportedclientsthatallowremoteconnectionstoaDIVARIPsystemthrough
theinternet.
5.3.1 RemoteconnectionwithOperatorClient
TomakearemoteconnectionwithBoschVMSOperatorClient
1. DownloadtheresourcefolderoftheBoschVMSinstallerusingthefollowingnetwork
share:
\\<IPaddressofDIVARIP>\sources
2. CopytheSetupdirectorytotheremoteworkstationthatwillbeusedforremoteviewing.
3. IntheSetupdirectory,right-clicksetup.exe,thenclickRunasadministratorandaccept
thesecuritymessage.
4. IntheWelcomedialogboxclearallcheckboxesexceptOperatorClient.
5. Followtheinstallationprocess.
6. Afterfinishingtheinstallersuccessfully,startOperatorClientusingthedesktopshortcut.
7. Enterthefollowing,thenclickOK.
Username:admin
Password:enteruserpassword
Connection:enterpublicIPaddressordynDNSname
5.3.2 RemoteconnectionwithVideoSecurityApp
TomakearemoteconnectionwithVideoSecurityApp:
1. InApple’sAppStoresearchforBoschVideoSecurity.
2. InstalltheVideoSecurityapponyouriOSdevice.

DIVARIP3000 Connectingtotheinternet|en 17
BoschSicherheitssystemGmbH InstallationManual 2014.11|V5|DOC
3. StarttheVideoSecurityapp.
4. SelectAdd.
5. EnterthepublicIPaddressordynDNSname(seeSettingupportforwarding).
6. MakesureSecureConnection(SSL)isswitchedon.
7. SelectAdd.
8. Enterthefollowing:
Username:admin
Password:enteruserpassword
Notice!
OnlyuseBoschVMSOperatorClientVideoSecurityAppintheversionthatmatchesDIVARIP.
Otherclientsorapplicationsoftwaremayworkbutarenotsupported.
5.4 InstallinganEnterpriseManagementServer
ForacentralmanagementofmultiplesystemsyoucaninstallBoschVMSEnterprise
ManagementServeronaseparateserver.
ToinstallBoschVMSEnterpriseManagementServeronaseparateserver:
1. DownloadtheresourcefolderoftheBoschVMSinstallerusingthefollowingnetwork
share:
\\<IPaddressofDIVARIP>\sources
2. CopytheSetupdirectorytotheserverthatshouldactasanEnterpriseManagement
Server.
3. IntheSetupdirectory,right-clicksetup.exe,thenclickRunasadministratorandaccept
thesecuritymessage.
4. IntheWelcomedialogbox,clearallcheckboxesexceptEnterpriseManagementServer
andConfigurationClient.
5. Followtheinstallationinstructions.
6. Afterfinishingtheinstallersuccessfully,startConfigurationClientusingthedesktop
shortcut.
Notice!
ForEnterpriseManagementServerconfigurationrefertotheBoschVMSdocumentation.

18 en|Recoveringtheunit DIVARIP3000
2014.11|V5|DOC InstallationManual BoschSicherheitssystemGmbH
6 Recoveringtheunit
Followingproceduredescribeshowtorestorethefactorydefaultimage.
Torestoretheunittofactorydefaultimage
1. StarttheunitandpressF7duringtheBIOSpower-on-self-test.
TheRecoverymenuisdisplayed.
Notice!
MakesurethataVGAmonitor,akeyboardandamouseareconnectedtotheunit.
2. Selectoneofthefollowing:
–Initialtofactoryimage(alldatawillbedeleted)
(restorestofactorydefaultimageanddeletesalldataontheHDDs)
or
–RestoretoFactoryimage(alldatawillnotbedeleted)
(restorestofactorydefaultimage;dataontheHDDswillnotbedeleted)
Note:
Windowsperformsthesetup.Thescreendisplaysthepercentageoftheprocess.
Notice!
Donotturnofftheunitduringtheprocess.ThiswilldamagetheRecoverymedia.
3. TheunitstartsfromtheRecoverymedia.Ifthesetupissuccessful,pressYestorestart
thesystem.
4. Windowsperformstheinitialsetupoftheoperatingsystem.Theunitrestartsafter
Windowshascompletedthesetup.
5. Aftertherestartoftheunit,thefactorysettingsareinstalled.

DIVARIP3000 AdditionalDocumentationandclientsoftware|en 19
BoschSicherheitssystemGmbH InstallationManual 2014.11|V5|DOC
7 AdditionalDocumentationandclientsoftware
DocumentationforBoschSecuritySystemsproductscanbefoundasfollows:
4Openanybrowser>enterwww.boschsecurity.com>selectyourregionandyourcountry
>startasearchforyourproduct>selecttheproductinthesearchresultstoshowthe
existingdocuments.
Andonthefollowingnetworkshare:
4\\<IPaddressofDIVARIP>\sources

BoschSicherheitssystemeGmbH
Robert-Bosch-Ring5
85630Grasbrunn
Germany
www.boschsecurity.com
©BoschSicherheitssystemeGmbH,2014