Bosch VIP-X1XF-E User manual

VIP X1 XF E
VIP-X1XF-E
en Quick Installation Guide

VIP X1 XF E Table of Contents | en 3
Bosch Sicherheitssysteme GmbH Quick Installation Guide F.01U.269.645 | V2 | 2012.06
Table of Contents
1 About this Quick Installation Guide 4
2 Parts included 5
3 Unpacking 6
4 Installation 7
4.1 Preparing for wall-mounting 7
4.2 Mounting the frame 8
4.3 Placing the unit in the frame 9
5 Connection 10
5.1 Connecting the camera and audio 10
5.2 Creating a serial connection 11
5.3 Alarm and relay connections 12
5.4 Establishing the network connection 13
5.5 Connecting the power supply 14
6 Assigning an IP address 15

4en | About this Quick Installation Guide VIP X1 XF E
F.01U.269.645 | V2 | 2012.06 Quick Installation Guide Bosch Sicherheitssysteme GmbH
1 About this Quick Installation Guide
This Quick Installation Guide applies to all variants of the
VIP X1 XF E.
For further detailed information, please see the extensive
online Help for the VIP X1 XF E.
This Quick Installation Guide, the Installation and Operating
Manual and the current firmware package are available in
various languages at www.boschsecurity.com.
WARNING!
You should always make yourself familiar with the required
safety measures (see Safety document enclosed).
Only operate the VIP X1 XF E in combination with an LPS/NEC
Class 2 power supply unit with limited output.
This Quick Installation Guide only describes the basic
procedure for installing a VIP X1 XF E and cannot replace the
complete manual.

VIP X1 XF E Parts included | en 5
Bosch Sicherheitssysteme GmbH Quick Installation Guide F.01U.269.645 | V2 | 2012.06
2 Parts included
– 1 VIP X1 XF E network video server
– 1 terminal block
– 4 self-adhesive elastic bumpers
– 1 wall-mounting panel
–2screws
– 2 wall plugs
– 1 Quick Installation Guide
– 1 Safety Hints

6en | Unpacking VIP X1 XF E
F.01U.269.645 | V2 | 2012.06 Quick Installation Guide Bosch Sicherheitssysteme GmbH
3 Unpacking
– Check that the delivery is complete and in perfect
condition.
– Arrange for the unit to be checked by
Bosch Security Systems if you find any damage.

VIP X1 XF E Installation | en 7
Bosch Sicherheitssysteme GmbH Quick Installation Guide F.01U.269.645 | V2 | 2012.06
4 Installation
4.1 Preparing for wall-mounting
You can secure the VIP X1 XF E to any load-bearing wall using
the wall-mounting panel, in either a vertical or a horizontal
position.
CAUTION!
If mounting the unit in a vertical position, you will need to use
the lower plastic frame and then place the unit onto the frame
from above. If mounting the unit in a horizontal position, you
can use either of the two frames.

8en | Installation VIP X1 XF E
F.01U.269.645 | V2 | 2012.06 Quick Installation Guide Bosch Sicherheitssysteme GmbH
4.2 Mounting the frame
– Lift the plastic frame on one side of the housing and
carefully remove it from the unit.
– Screw the plastic frame in the required position together
with the wall-mounting panel.
– Check that the plastic frame is secure.
CAUTION!
The mounting location must be able to reliably hold the unit.
The load-bearing capacity must be adequate for four times the
weight of the unit.

VIP X1 XF E Installation | en 9
Bosch Sicherheitssysteme GmbH Quick Installation Guide F.01U.269.645 | V2 | 2012.06
4.3 Placing the unit in the frame
– Place the unit on the wall-mounting panel, with the panel
positioned between the housing and the second plastic
frame.
– Slide the unit into the plastic frame until you feel it lock
securely into place.
– Finally, check that the unit is securely attached in the
installation location.

10 en | Connection VIP X1 XF E
F.01U.269.645 | V2 | 2012.06 Quick Installation Guide Bosch Sicherheitssysteme GmbH
5 Connection
5.1 Connecting the camera and audio
– Connect the camera to the socket VIDEO IN.
– Use the LINE IN/OUT socket for audio line connections.
CAUTION!
Please observe the following specifications:
Line In: 9 kOhm typ., 5.5 Vp-p max.
Line Out: 16 Ohm min., 3 Vp-p max.