Bosch VMD01 M50 PAL User manual

610–4.998.137.762
Ausgabe: 1
Stand: Februar 03
VMD01 – M50 PAL
VMD01 – M60 NTSC
EN Operating instrutions Video Motion Detector
FR Utilisation Détecteur de mouvement vidéo
DE Bedienungsanleitung Videobewegungssensor
SP Instucciones de servicio Sensor de movimiento de vídeo
NL Handleiding Videobewegingssensor
IT Instruzioni per l’uso Sensore di movimento video
PO Manual de operação Vídeo–sensor de movimentos
Security Systems

– 2 – A1 February 03/Trb
FCC
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/TV technican for help.
Recognized Component Mark for Canada and the United States
If the unit is used as a stand alone, it must be supplied via a power supply which fulfils the
requirement on “SELV” and on a Limited Power Source.
If the unit is mounted into a 19” rack a suitable fire enclosure must be provided in the
end–unit.
EU Declaration of Conformity
Bosch declares, this product: is conform to the following standards:
Supplementary Information: “The product complies with the requirements of the low
Voltage Directive 73/23EEC and the EMC Directive 89/336/EEC.”
This product is carrying the CE–Mark in accordance with the related European
Directives. Responsible for CE–Marking is
Bosch Sicherheitssysteme GmbH
Security Systems Division
Ludwig–Boelkow–Allee
85521 Ottobrunn
Germany

– 3 – A1 February 03/Trb
TABLE OF CONTENTS English
Chapter Page
1 Introduction 38
2 Mounting 39
3 Functions 42
4 System structure 44
5 Programming 45
6 Operating instructions 50
7 Technical data 52
8 Notes 53
Français 20
German 37
Español 54
Italiano 71
Dutch 88
Portuguese 105
Note:
Additional information about the product, installation, and operation can be found at:
http://www.boschsecuritysystems.com

– 4 – A1 February 03/Trb
1 Introduction English
This is a high-quality single-channel video movement sensor for direct
integration in an analog CCTV system.
Video signals are evaluated through image analysis and interpretation.
Alarm, pre-alarm and post-alarm images are stored.
Additional information on project planning and the software tool can be
obtained in electronic form through a dealer or installer.
Statutes/Norms/Guidelines met by the unit
– EMV law on the basis of
DIN EN 50081–1 (radiated noise)
DIN EN 50130–4 (noise immunity)
– DIN EN 60950 (electrical safety)
– Environment to IEC 68–2–2/Degree I, 68–2–1, 68–2–30
The product carries the CE symbol.
Registration: FCC
Registration: Recognition Component Mark for Canada and the United States
(File number: E221534)
Basic shipment contents Accessories
– Basic device (VMD01–M50/M60) – Power supply VMD–PS
– Operating instructions – Wall holder VMD–WM
– 15-pin Sub–D plug – Mouse VMD–SM
– Flat box with rubber feet and – 19” frame incl. mounting
brackets VMD–RA90
– 19”frame incl. mounting brackets
without power supply/cable set/
Distributor LP, with blind plate
VMD–RA00
– 19” blind plate VMD–RADC
Camera, monitor, recorder, mouse (for programming) and cabling are not part
of the shipment contents.
Alarm contact
Only for programming

– 5 – A1 February 03/Trb
2 Mounting English
2.1 General mounting notes
– Use only cable specified by the manufacturer. Protection against
malfunction cannot otherwise be guaranteed.
– To guarantee operational safety, only those power supplies specified by the
manufacturer may be used. (individual devices: power supply VMD–PS, for
19” installation, the power supply is integrated in the VMD–RA frame).
– For questions regarding setup, environmental conditions and safety of
individual components, manufacturer documentation must be consulted.
– For installation, this instruction manual and the specific connection
instructions are to be followed.
– This description does not contain information about installation and setup of
the camera, monitor and recorder.
2.1.1 Mounting Variants
Locking
spring
Unit feet
Feet
1. Press in
2. Press in
3. Press down with blunt object
Housing vertical
Four feet must be fitted to the unit base plate. The connecting cable must have
sufficient strain relief.
Housing can be stacked upright.
Warning!
Maximum of four units can be stacked upright on top of each other.
If housings are stacked on top of each other, the feet on the underside of the
housing must be fitted. There are no locking springs for the bottom unit. For all
other units to be stacked, the locking springs must be pushed into the feet and
pressed into the locating slits on the bottom unit. Ensure sufficient strain relief.

– 6 – A1 February 03/Trb
Mounting continued English
2.1.2 Wall holder for mounting on walls and ceilings (accessory VMD–WM)
Mounting holes
for housing Holes for
strain relief
Holes for
strain relief
TOP TOP
The wall holder can be used as a drilling template. Before mounting on a wall,
screw the wall holder (using fitting holes for housing) to the unit. For strain relief
using cable ties, use the holes in the mounting plate.
Warning!
Only one unit may be mounted on a wall or ceiling.
2.1.3 Connections / Front
3
2
4
1
1L1 green 2L2 red
3Key/Rotary Switch 4Mouse connection, RS232 serial interface
2.1.4 Connections / Rear
12341
6
11
15V DC 2I/O Contacts
3Video OUT 4Video IN

– 7 – A1 February 03/Trb
Mounting continued English
2.2 19” mounting frame and wiring
(Accessory VMD–RA90)
Maximum expansion
8 units mounting
bracket
Front
Power supply
Rear
LIEG+5V –5V
100–240V
Power supply
Direction of swivel
+5V
100–240V
Fuse = 2A
Top view (distributor LP)
For rack mounting, insert the mounting angle brackets (packaged extra) into
the slides, screw down and feed the cabling through.
Warning
Grounding must be professionally carried out according to IEN 60950.
2.2.1 19” mounting frame without wiring (accessory VMD–RA00)
The frame is delivered without power supply/cable set/distributor LP, with blind
plate.

– 8 – A1 February 03/Trb
3 Functions English
3.1 Overlaid lines for color and B/W signals
Color Black/White
Alarm object: Striped line with high contrastRed
Pre-alarm object: Yellow Striped line with low contrast
Tracking line: Green Striped line
Color Black/White
Area of sensitivity: Striped lineGreen
Perspective: Green:Foreground
Blue: Background Striped lines; Foreground square: Larger dotted line
Background square: Smaller dotted line
Directionality: Striped lines;
Directional arrow with smaller dotted lines
Tolerance lines with larger dotted lines
Green: Direction
Blue: Tolerance
Configuration
Live and archived images
3.2 Rotary switch
Operation Function
Briefly press
Briefly press again
Rotate right
Alarm image memory on
Alarm image memory off
Rotate left Backwards in alarm archive (–)
Forwards in alarm archive (+)
Long press (> 2 sec.) Acknowledge alarm
3.3 Light emitting diodes
LED Status
off
on
L2 red
(when L1 on)
L1 green
Blinking
off
on
Blinking
L2 red
(when L1 blinking) off
Function
No supply of power to unit
Unit operating normally
Unit malfunction as combined message
Unit defective and/or video channel malfunction
No alarm, not armed
No alarm, armed
Object detected/Alarm on
No malfunction on video signal,
unit malfunctioning
on No video signal, no general unit malfunction
Blinking Video signal interference:
1. Signal/Noise ratio too low
2. Camera blinded
3. Scene lighting level too low

– 9 – A1 February 03/Trb
Functions continued English
3.4 Contact assignment
PIN
1
Electrical specification
Input contact I
Open: sensor armed
At ground (Pin 5): Sensor disarmed
2
3
4
5
6
7
8
9
10
12
13
14
Output contact I
Internally switched to ground: Object detected
Open: No object detected
(constant signal, impulse or periodic impulse)
Output contact II
Internally switched to ground:
Video signal malfunction
Open: Video signal OK
Ground
Relay I
6/7 closed: Malfunction
Relay I (Middle contact)
Relay I
8/7 closed: No malfunction
Relay II
9/10 closed: No alarm
Relay II (Middle contact)
Remote control Rotary switch:
Backwards in alarm archive (–) when turned left
Remote control Rotary switch:
Forwards in alarm archive (–) when turned right
Internal pull-up
Internal pull-up
Open collector,
max. 100mA, 12V
Externally switchable
Max. 30V, max. 1A
Function
Input contact II
Open: Parameter set I active
At ground (Pin 5):
Parameter set II active
Open collector,
max. 100mA, 12V
Externally switchable
Max. 30V, max. 1A
Max. 30V, max. 1A
Max. 30V, max. 1A
Max. 30V, max. 1A
11 Relay II
11/10 closed: Alarm Max. 30V, max. 1A
Internal pull-up
Remote control Rotary switch:
– Switchover: Live image/alarm archive
– active >2 secs. = alarm acknowledgement
Internal pull-up
Internal pull-up
15 Remote control Rotary switch: Ground
Input contacts +5V Output contacts
1/2
12/13/14
5/15
3/4
5/15
–
Remote control

– 10 – A1 February 03/Trb
4 System structure English
4.1 Menu
Change code number
Language
Programming
Parameter set 1
Alarm set 1
Operating mode set 1
Alarm contact set 1
Sensor parameter set 1
Area of sensitivity set 1
Object size/Perspective set 1
Direction of movement set 1
Parameter set 2
Alarm set 2
Operating mode set 2
Alarm contact set 2
Sensor parameter set 2
Area of sensitivity set 2
Object size/Perspective set 2
Direction of movement set 2
Copy parameter set
System information
Exit