Bosch SEC-RFPB60M-433 User manual

Pendant transmitter, 433MHz
SEC‑RFPB60M‑433
en Installation Manual

Pendant transmitter, 433MHz Table of contents | en 3
Bosch Security Systems B.V. Installation Manual 2019.07 | SE3v1.1 | DL
Table of contents
1Copyright, safety and warranty 4
1.1 Copyright information 4
1.2 Important safety notes 5
1.3 Safety precautions 6
1.4 Certification information 6
1.4.1 FCC/IC information 6
1.4.2 Other certification information 7
2System overview 8
3Installing the transmitter 9
4Using the transmitter 13
4.1 Supervision feature of the transmitter 13
4.2 Generating a manual duress alarm 13
4.3 Resetting transmitter alarm 13
4.4 Testing the transmitter 14

4en | Copyright, safety and warranty Pendant transmitter, 433MHz
2019.07 | SE3v1.1 | DL Installation Manual Bosch Security Systems B.V.
1 Copyright, safety and warranty
1.1 Copyright information
All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, without the prior written permission of BOSCH SECURITY SYSTEMS.
This manual is provided pursuant to a license agreement containing restrictions on their use.
The manual contains valuable trade secrets and proprietary information of BOSCH SECURITY
SYSTEMS and is protected by international copyright law. It may not be copied or distributed
to third parties, or used in any manner not provided for in the said license agreement.
All software is provided "AS IS." The sole obligation of BOSCH SECURITY SYSTEMS shall be to
make available all published modifications that correct program problems are published within
one (1) year from the date of shipment.
The software is intended for use only with the hardware specified in this manual and in the
absence of other software. Concurrent use with other software or with hardware not specified
may cause the program to function improperly or not at all. BOSCH SECURITY SYSTEMS may
not provide support for systems operating under such conditions.
All efforts have been made to ensure the accuracy of the contents of this manual. The above
notwithstanding, BOSCH SECURITY SYSTEMS assume no responsibility for any errors in this
manual or their consequences.
The information on this document is subject to change without notice.
Other product and company names mentioned herein may be the trademarks of their
respective owners.

Pendant transmitter, 433MHz Copyright, safety and warranty | en 5
Bosch Security Systems B.V. Installation Manual 2019.07 | SE3v1.1 | DL
1.2 Important safety notes
1. Read, Follow, and Retain Instructions – All safety and operating instructions must be
read and followed properly before putting the unit into operation. Retain instructions for
future reference.
2. Consider all Warnings – Adhere to all warnings on the unit and in the operating
instructions.
3. Accessories – Use only accessories recommended by the manufacturer or those sold
with the product. Accessories not recommended by the manufacturer shall not be used,
as they may cause hazards.
4. Installation Precautions – Do not place this unit on an unstable stand, tripod, bracket, or
mount. The unit may fall, causing serious injury to persons and damage to the unit. Mount
the unit according to the manufacturer’s instructions.
5. Service – Do not attempt to service this unit by yourself. Opening or removing covers may
expose you to dangerous voltages or other hazards. Refer all servicing to qualified service
personnel.
6. Damage Requiring Service – Disconnect the unit from the main AC or DC power source
and refer servicing to qualified service personnel under the following conditions:
– When the power supply cord or plug is damaged.
– If liquid has been spilled or an object has fallen into the unit.
– If the unit has been exposed to water and/or inclement weather (rain, snow, etc.).
– If the unit does not operate normally, when following the operating instructions.
Adjust only those controls specified in the operating instructions. Improper
adjustment of other controls may result in damage, and require extensive work by a
qualified technician to restore the unit to normal operation.
– If the unit has been dropped or the cabinet damaged.
– If the unit exhibits a distinct change in performance, this indicates that service is
needed.
7. Replacement Parts – When replacement parts are required, the service technician shall
use replacement parts that are specified by the manufacturer. Unauthorized substitutions
may result in fire, electrical shock or other hazards.
8. Safety Check – Upon completion of service or repair work on the unit, ask the service
technician to perform safety checks to ensure that the unit operates properly.
9. Power Sources – Operate the unit only from the type of power source indicated on the
label. If unsure of the type of power supply to use, contact your dealer.
– For units intended to operate from battery power, refer to the operating instructions.
– For units intended to operate with External Power Supplies, use only the
recommended approved power supplies.
10. Lightning – For added protection during a lightning storm, or when this unit is left
unused for long periods of time, disconnect the unit from power. This will prevent
damage to the unit due to lightning and excessive power line surges.
11. Restricted Access Locations are required for the installation.

6en | Copyright, safety and warranty Pendant transmitter, 433MHz
2019.07 | SE3v1.1 | DL Installation Manual Bosch Security Systems B.V.
1.3 Safety precautions
Disposal
Your Bosch product has been developed and manufactured using high-
quality materials and components that can be reused.
This symbol means that electronic and electrical devices that have reached
the end of their working life must be disposed of separately from
household waste.
In the EU, separate collecting systems are already in place for used
electrical and electronic products. Please dispose of these devices at your
local communal waste collection point or at a recycling center.
1.4 Certification information
1.4.1 FCC/IC information
This device complies with Part 15 FCC Rules and Industry Canada's license-exempt RSSs.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received including interference
that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Pendant transmitter, 433MHz Copyright, safety and warranty | en 7
Bosch Security Systems B.V. Installation Manual 2019.07 | SE3v1.1 | DL
1.4.2 Other certification information

8en | System overview Pendant transmitter, 433MHz
2019.07 | SE3v1.1 | DL Installation Manual Bosch Security Systems B.V.
2 System overview
The Security Escort pendant transmitters are security transmitters designed to work with the
Security Escort system. In normal supervision mode, the transmitter sends a signal to the
central console at regular fixed intervals, to notify the system of its last known location.
During an emergency, the subscriber initiates an alarm. The alarm signal identifying the
transmitter and its location is sent to the Security Escort central console. During the alarm,
the auto-tracking feature sends a signal to the central console at short successive intervals to
constantly update and track its location.

Pendant transmitter, 433MHz Installing the transmitter | en 9
Bosch Security Systems B.V. Installation Manual 2019.07 | SE3v1.1 | DL
3 Installing the transmitter
This section provides information on how to install the battery and set up the transmitter.
The transmitter uses a 3 VDC, CR2032 lithium coin cell battery. The following battery types
are recommended: Duracell® DL2032, Eveready® CR2032, or Panasonic® CR2032.
Assuming normal usage (such as weekly testing), the battery life of SEC-RFPB60M-433 should
be approximately 3 years.
Notice!
This equipment can be damaged by static electricity. Use a ground strap or grounded
workstation when changing batteries.
You need a Phillips P1 screwdriver to install or replace the batteries.
1. Use the screwdriver to remove the screw from the back cover of the transmitter.
2. Remove the back cover from the transmitter.

10 en | Installing the transmitter Pendant transmitter, 433MHz
2019.07 | SE3v1.1 | DL Installation Manual Bosch Security Systems B.V.
3. Insert or replace the battery, placing the positive (+) polarity facing the inside of the
transmitter.
!
Caution!
Risk of explosion
Replacement of the battery with an incorrect type is subject to the risk of explosion. Batteries
must not be disposed of in household waste to avoid the risk of explosion.
4. Place the back cover of the transmitter into its original position.

Pendant transmitter, 433MHz Installing the transmitter | en 11
Bosch Security Systems B.V. Installation Manual 2019.07 | SE3v1.1 | DL
5. Insert and fasten the screw of the back cover.
6. Register the transmitter in the Security Escort database using the RFID code at the back
of the transmitter, if necessary.

12 en | Installing the transmitter Pendant transmitter, 433MHz
2019.07 | SE3v1.1 | DL Installation Manual Bosch Security Systems B.V.
7. Test the transmitter for proper operation by generating an alarm.

Pendant transmitter, 433MHz Using the transmitter | en 13
Bosch Security Systems B.V. Installation Manual 2019.07 | SE3v1.1 | DL
4 Using the transmitter
This section provides information on the features and how to use the transmitter.
4.1 Supervision feature of the transmitter
Supervision is provided by transmitting a low power level signal to the receiver every 60
minutes if there is no other activity. The supervision duration is fixed and non-configurable.
4.2 Generating a manual duress alarm
During an emergency, the subscriber presses and holds both alarm buttons simultaneously for
600 milliseconds or more to generate a duress alarm. The LED starts blinking and illuminate
for a longer period one final time. This is when the transmitter sends an alarm signal to the
central console, and the LED of the transmitter then turns off.
Figure4.1: Generating a manual duress alarm
The same result can be achieved by pressing and holding one of the alarm buttons. Without
releasing this alarm button, press and hold the other unused alarm button for 600
milliseconds or more to generate a duress alarm.
After the alarm is initiated, the auto-tracking feature begins. The transmitter continues to
transmit its location to the central console automatically every 10 seconds, for a duration of
10 minutes.
4.3 Resetting transmitter alarm
To reset the transmitter during the auto-tracking period after generating a manual duress
alarm, perform a test sequence as described in Testing the transmitter, page 14. Otherwise,
the transmitter will time out after 10 minutes and automatically reset to the normal state.

14 en | Using the transmitter Pendant transmitter, 433MHz
2019.07 | SE3v1.1 | DL Installation Manual Bosch Security Systems B.V.
4.4 Testing the transmitter
To start the test sequence, press either one of the buttons on the transmitter for about 1
second. The LED of the transmitter will start to blink rapidly.
Figure4.2: Press either one of the buttons to start the test sequence
To complete the test sequence before the transmitter times out after 3 seconds, press the
other unutilized button for about 1 second. The LED of the transmitter continues to blink
rapidly during this period.
Figure4.3: Press the other unutilized button before the 3 seconds time out
If the test sequence is completed successfully, the LED of the transmitter will illuminate for a
longer period a final time. A test transmission is sent to the central console and the LED of the
transmitter will switch off.

Pendant transmitter, 433MHz Using the transmitter | en 15
Bosch Security Systems B.V. Installation Manual 2019.07 | SE3v1.1 | DL
You may abort the test by not doing anything after starting the test sequence, and letting it
time out after 3 seconds. The LED of the transmitter will stop blinking after the test sequence
has timed out.

Bosch Security Systems B.V.
Torenallee 49
5617 BA Eindhoven
Netherlands
www.boschsecurity.com
© Bosch Security Systems B.V., 2019