Bosch SE88A-90S-304 User manual

Safety and Copyright
Federal Communication Commission (FCC)
Statement
This device complies with Part 15 of the FCC
rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interfer-
ence, and
2. This device must accept any interference re-
ceived, including interference that may cause
undesired operation.
Copyright
TORX® is a trademark of Textron Inc.
Industry Canada (IC) Statement
This device complies with Industry Canada Li-
cense-exempt RSS standard(s). Operation is
subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, in-
cluding interference that may cause un-
desired operation of the device.
Le présent appareil est conforme aux CNR d'In-
dustrie Canada applicables aux appareils radio-
exempts de licence. L'exploitation est autorisée
aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage,
et
2. l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compro-
mettre le fonctionnement.
Short information
The SE88 is an asset transmitter designed to
work with the Security Escort system. When ini-
tiated, a signal identifying the asset and location
is sent to the security office at regular intervals.
SE88 can be tested within sight of a receiver or
siren/strobe.
Notice!
The Security Escort system is not a
substitute for safe behavior. System
users should not take personal risks un-
der the misconception the system
provides protection that compensates
for taking such risks.
Overview
The overview specifications of the transmitter
are as follows:
SE88A-90S Provides a supervisory transmis-
sion to the Security Escort System
every 90 seconds
Battery Lithium coin cell battery. Duracell
DL2032, Eveready CR2032,
Panasonic CR2032
Operating
Temperature
0° C to +60° C
(-32° F to +140° F)
Enclosure
Dimension
(W x H x D)
31 mm x 54 mm x 7.5mm
(1.22 in x 2.12 in x 0.3 in)
Tab.1: Specifications
Fig.1: SE88 Asset Transmitter Parts
1 Enclosure 2 Test Button
3 Screw 4 Slide Cover
Testing the Transmitter
Test the transmitter weekly. To verify transmit-
ter operation:
1. You must be in sight of a Security Escort
Siren/Strobe or a Security Escort Receiver.
Receivers are located inside buildings usually
within sight of an exit door. They are moun-
ted on walls in light beige, rectangular en-
closures. Siren/strobe is typically mounted
on outside building walls and on light poles.
2. Press the Test button on your transmitter for
about 1 second and release it.
3. Look for a flashing strobe on a siren/strobe,
or a flashing green light on a receiver. These
indicators confirm that the entire system is
working. If you do not see the flashing light
or flashing strobe, the test was not success-
ful.
Notice!
Before the flashing light appears, there
might be a brief delay of 2 or 3
seconds.
Notice!
For testing of the transmitter using
siren, the siren needs to be connected
to the strobe output (ST-) and not the
siren output (SI-) of the Alert Unit.
Please refer to the wiring in the EA120B
Alert Unit Installation Instructions.
If there is no response, try the test again. If
there is no response the second time, your
transmitter may not be working. Take the trans-
mitter to the security office.
Installing/Changing Batteries
Assuming normal usage (such as weekly test-
ing), the battery life of SE88A-90S should be ap-
proximately 1 year.
If the battery is weak, a special signal is sent to
the security office during any test, alarm, or su-
pervisory transmission. Tests do not produce a
flashing light on a receiver or siren/strobe when
your transmitter has a weak battery.
Notice!
This equipment can be damaged by
static electricity. Use a ground strap or
grounded workstation when changing
batteries.
You need a TORX® T5 wrench to replace the bat-
teries.
1 | 2 | 3 | 4 |
5 | 6 | 7 | 8 |

1. Remove the screw from the slide cover.
2. Remove the slide cover from the enclosure.
3. Insert the battery, placing the + (positive)
side of the battery away from the enclosure.
4. Ease the slide cover into position and press
to snap it in place.
5. Insert the screw on the slide cover and
tighten.
6. Test the transmitter for proper operation.
Important Information for Users of
Security Escort System
Protected Areas
Check with the security department to verify the
exact areas of the facility that are protected by
the system and those that are not.
Lost or Stolen Transmitters
If your transmitter is lost or stolen, report the in-
cident immediately to the security office so a re-
placement can be issued and the original trans-
mitter can be deleted from the system.
Tips for Better Transmission
As with all radio equipment, the signal strength
from the transmitter is reduced by metal and
wet surfaces and to some extent by the human
body.
Battery Life
Assuming normal usage (such as weekly test-
ing), the battery lasts approximately one year. If
the battery is weak, a special signal is sent to
the security office during a test. This test will
not produce a flashing light on the receiver or
siren/strobe.
Exposure to Moisture
Test the transmitter a few times (several hours
apart) once exposed to moisture to verify it is
working properly.
9 | 10 | 11 |
12 | 13 | 14 |
SE88A Series Asset Transmitters
SE88A-90S-304
en User Manual
Robert Bosch (SEA) Pte Ltd
11 Bishan Street 21
573943 Singapore
Singapore
www.boschsecurity.com
© Robert Bosch (SEA) Pte Ltd, 2016
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
© Bosch Sicherheitssysteme GmbH, 2016
F.01U.318.126 | V1.1