Boser HS-2613 User manual

HS-2613
VIA V4 Eden processor
Embedded Engine Board
•CompactFlash•8-bit I/O•DVI-D/CRT/LVDS•TV-Out•
•Dual LAN•Audio•SATA•ATA/33/66/100•
•RS-232/422/485•4 COM•5 USB2.0•
•PCI-104•WDT•H/W Monitor•

Copyright Disclaimers
The accuracy of contents in this manual has passed thorough checking and review before
publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for
any infringements of patents or other rights resulting from its use. The manufacturer will
not be responsible for any direct, indirect, special, incidental or consequential
damages arising from the use of this product or documentation, even if advised of
the possibility of such damage(s).
This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation, and
storage of any form and means (i.e., electronic, mechanical, photocopying, recording)
of this document, in whole or partly, is prohibited, unless granted permission by BOSER
Technology Co., Ltd.
BOSER Technology Co., Ltd. reserves the right to change or improve the contents of
this document without due notice. BOSER Technology Co., Ltd. assumes no
responsibility for any errors or omissions that may appear in this manual, nor does
it make any commitment to update the information contained herein.
T
T
Tr
r
ra
a
ad
d
de
e
em
m
ma
a
ar
r
rk
k
ks
s
s
BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
AMI is a registered trademark of AMI Software, Inc.
All other trademarks, products and or product names mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or
registered trademarks of their respective companies or owners.
© Copyright 2008 BOSER Technology Co., Ltd.
All Rights Reserved.
Edition 1.9, April 08, 2010

Table of Contents
Chapter 1 General Description ..................................1
1.1 Major Features....................................................................... 2
1.2 Specifications ........................................................................ 3
1.3 Board Dimensions................................................................. 4
Chapter 2 Unpacking ..................................................5
2.1 Opening the Delivery Package............................................. 5
2.2 Inspection............................................................................... 5
Chapter 3 Hardware Installation ..............................7
3.1 Before Installation ................................................................. 7
3.2 Board Layout ......................................................................... 8
3.3 Jumper List ............................................................................ 9
3.4 Connector List ....................................................................... 9
3.5 Configuring the CPU ........................................................... 10
3.6 System Memory ................................................................... 10
3.7 VGA Controller .................................................................... 10
3.8 IDE Drive Connector ........................................................... 12
3.9 Serial ATA Connector ......................................................... 12
3.10 Serial Port Connectors ....................................................... 13
3.11 Ethernet Connector............................................................. 14
3.12 USB Port............................................................................... 15
3.13 CMOS Data Clear................................................................. 15
3.14 Power and Fan Connectors................................................ 15
3.15 Keyboard/Mouse Connectors ............................................ 16
3.16 System Front Panel Control ............................................... 17
3.17 Watchdog Timer .................................................................. 18
3.18 TV-Out Function .................................................................. 19
3.19 PCI-104 Connector .............................................................. 20
3.20 Audio Connectors ............................................................... 22
3.21 CompactFlashSocket ...................................................... 22
3.22 8-bit I/O Function................................................................. 24

Chapter 4 AMI BIOS Setup..................................... 29
4.1 Starting Setup...................................................................... 29
4.2 Using Setup ......................................................................... 30
4.3 Main Menu............................................................................ 31
4.4 Advanced Settings .............................................................. 32
4.5 Advanced PCI/PnP Settings............................................... 37
4.6 Boot Settings ....................................................................... 38
4.7 Security Settings ................................................................. 39
4.8 Advanced Chipset Settings................................................ 40
4.9 Exit Options ......................................................................... 43
Chapter 5 Award BIOS Setup ................................. 45
5.1 Starting Setup...................................................................... 45
5.2 Using Setup ......................................................................... 46
5.3 Main Menu............................................................................ 47
5.4 Standard CMOS Features................................................... 48
5.5 Advanced BIOS Features ................................................... 49
5.6 Advanced Chipset Features............................................... 50
5.7 Integrated Peripherals ........................................................ 52
5.8 Power Management Setup ................................................. 54
5.9 PnP/PCI Configurations...................................................... 55
5.10 PC Health Status ................................................................. 56
5.11 Frequency/Voltage Control ................................................ 56
Chapter 6 Software Utilities..................................... 57
6.1 VGA Driver Installation ....................................................... 58
6.2 Audio Driver Installation..................................................... 59
6.3 LAN Driver Installation........................................................ 63
6.4 USB2.0 Driver Installation .................................................. 65

Declaration of Conformity -- CE Mark
BOSER Technology hereby acknowledges that compliance testing in
accordance with applicable standards of the EU’s EMC Directive,
89/336/EEC, was successfully completed on a sample of the equipment
identified below:
Equipment Class: Information Technology Equipment
Product Model Series: HS-2613
This Product Complies With: EN55022: Class A for Radiated emissions
EN50082-2: Heavy Industrial EMC Immunity
We, the undersigned, hereby declare that the equipment specified above
conforms to the above directives and standards.
Manufacturer:
BOSER TECHNOLOGY CO., LTD.

Safety Instructions
Integrated circuits on computer boards are sensitive to static electricity. To
avoid damaging chips from electrostatic discharge, observe the following
precautions:
 Do not remove boards or integrated circuits from their anti-static packaging
until you are ready to install them.
 Before handling a board or integrated circuit, touch an unpainted portion of
the system unit chassis for a few seconds. This helps to discharge any static
electricity on your body.
 Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components. Fasten the ALLIGATOR clip
of the strap to the end of the shielded wire lead from a grounded object.
Please wear and connect the strap before handle the HS-2613 to ensure
harmlessly discharge any static electricity through the strap.
 Please use an anti-static pad when putting down any components or parts or
tools outside the computer. You may also use an anti-static bag instead of
the pad. Please inquire from your local supplier for additional assistance in
finding the necessary anti-static gadgets.
NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC
PROTECTIONS.

1
Chapter 1
General Description
The HS-2613 is a VIA CX700(M) chipset-based board designed. The
HS-2613 is an ideal all-in-one embedded engine board. Additional
features include an enhanced I/O with CF, DVI-D/CRT/LVDS, TV-Out,
dual LAN, audio, SATA, 4 COM, USB2.0, and PCI-104 interfaces.
Its onboard ATA/33/66/100 to IDE drive interface architecture allows
the HS-2613 to support data transfers of 33 or 66MB/sec. to one IDE
drive connection. Designed with the VIA CX700(M), the board
supports VIA V4 Eden 1GHz CPU.
The VIA CX700(M) with 32/64/128MB shared main memory supports
CRT/Panel displays up to 1920 x 1440. It also supports 24-bit
single/dual-channel LVDS interface supporting up to 1600 x 1200.
System memory is also sufficient with the one SO-DDRII socket that
can support up to 1G.
Additional onboard connectors include an advanced USB2.0 port
providing faster data transmission. And two RJ-45 connectors for
10/100 Based Ethernet uses. To ensure the reliability in an unmanned
or standalone system, the watchdog timer (WDT) onboard HS-2613 is
designed with software that does not need the arithmetical functions of
a real-time clock chip. If any program causes unexpected halts to the
system, the onboard WDT will automatically reset the CPU or generate
an interrupt to resolve such condition.

2
1.1 Major Features
The HS-2613 comes with the following features:
 VIA V4 Eden processor 1GHz, supports 400MHz FSB
 1 x SO-DIMM up to 1GB DDR2 SDRAM
 VIA CX700(M) system chipset
 VIA CX700(M) integrated VGA for CRT & LVDS
 2 x 10/100 Mbps ethernet
 AC’97 audio codec
 Supports CF, 1 x SATA, 4 x COM, 5 x USB2.0, PCI-104
 Supports 24-bit LVDS, TV-Out, 8-bit I/O, +10~+30V wide range single
DC power in, H/W Monitor function
 Option for DVI-D display

3
1.2 Specifications
 System
 CPU
VIA V4 Eden processor 1GHz
 Front Side Bus
400MHz FSB
 BIOS
Award PnP Flash BIOS
 System Chipset:
VIA CX700(M)
 I/O Chipset
Winbond W83697UG
 System Memory
1 x 200-pin SO-DIMM socket DDR2 533MHz up to 1GB
 Storage
1 x Type II CF socket
 Watchdog Timer
Software programmable time-out intervals from 1~255 sec. or 1~255
min.
 Hardware Monitor
Monitoring temperatures, voltages, and cooling fan status
 Expansion Interface
PCI-104
 Power In
+10~+30V wide range single DC power in
 Operating Temperature
0~+60 degrees C
 Operating Humidity
0~95%, non-condensing
 Board Size (L x W)
145 x 102 mm
 I/O Interface
 MIO
3 x RS-232
1 x RS-232/422/485
5 x USB2.0 (4 x internal, 1 x external)
1 x IDE
1 x SATA
1 x PS/2 for KB/MS
 DI/O
8-bit input/output by parallel port

4
 Display
 Chipset
VIA CX700(M)
 Display Memory
32/64/128MB video memory
 LVDS
24-bit single/dual-channel
 TV-Out
Provides PAL or NTSC TV systems
 DVI Chipset
VIA CX700(M) (option)
 Resolution
CRT Mode: 1920 x 1440
LVDS Mode: 1600 x 1200
 Audio
 Chipset
VIA VT1708A
 Audio Interface (w/pin header)
MIC In, Line Out
 Ethernet
 Chipset
Dual RealTek RTL8100C 10/100 Mbps LAN
 Ethernet Interface
2 x RJ-45
1.3 Board Dimensions

5
Chapter 2
Unpacking
2.1 Opening the Delivery Package
The HS-2613 is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.
2.2 Inspection
After unpacking the board, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.
Integrated circuits will sometimes come out of their sockets during
shipment. Examine all integrated circuits, particularly the BIOS,
processor, memory modules, ROM-Disk, and keyboard controller chip
to ensure that they are firmly seated. The HS-2613 delivery package
contains the following items:
 HS-2613 Board x 1
 Utility CD Disk x 1, including User’s Manual
 Cables (as following table)
 Jumper Bag x 1

6
Cables Package
NO. Description QTY.
1 SATA cable 50cm (w/Lock) 1
2 COM DB9-10P(2.0-pitch) 15cm 2
3 SPK 8P(2.0) phone jack x 2 30cm 1
4 1-to-2 Mini DIN cable 19cm 1
5 4-pin to 4-pin terminal block power cable 1
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.
Option Accessories
NO. Description
1 SATA power cable
2 1-to-2 USB cable with bracket
3 COM DB9-10P (2.0-pitch)
4 DVI cable (291-13010040G)
5 40P(2.54)*2 - 44P(2.0)*2 45cm IDE flat cable

7
Chapter 3
Hardware Installation
This chapter provides the information on how to install the hardware
using the HS-2613. This chapter also contains information related to
jumper settings of switch, and watchdog timer selection etc.
3.1 Before Installation
After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to
take before you begin with your installation process.
1. Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper. (JP5 short 1-2)
2. Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections on this chapter
for the detailed information on the connectors.
3. Keep the manual and diskette in good condition for future
reference and use.

8
3.2 Board Layout

9
3.3 Jumper List
Jumper Default Setting Setting Page
JP1 Panel Voltage Select: +3.3V Short 1-2 10
JP3 CF Use Master/Slave Select: Slave Short 2-3 22
JP4 Display Out Function Select: CRT Short 1-2 19
JP5 Clear CMOS: Normal Operation Short 1-2 15
CN25 COM2 Use RS-232 or RS-422/485 Select:
RS-232 Open 13
3.4 Connector List
Connector Definition Page
CN1 MIC In/Line Out Connector 22
CN2 PCI-104 Connector 20
CN3/CN6/CN9 USB2.0 Port 15
CN4 Serial ATA Connector 12
CN5 Reset Button 17
CN7 Inverter Power In Connector 10
CN8 PS/2 6-pin Mini DIN 16
CN10/CN12 LVDS Panel Connector 10
CN11 IDE Connector 12
CN13/CN14 RJ-45 Connector 14
CN15 4-pin Power In Connector 15
CN16 15-pin CRT Connector 10
CN17 TV-Out Connector 19
CN18 RS-422/485 Connector 13
CN19 8-bit Input/Output 24
CN24/CN20/CN21/CN26 COM 1~COM 4 Connector (5x2 header) 13
CN23 System Front Panel Control 17
CN27 SO-DDRII Socket 10
CN28 CompactFlash Connector 22
CN29 External Power In Connector 15
CN30 DVI SM Bus 10
FN2 Fan Power In Connector 15

10
3.5 Configuring the CPU
The HS-2613 embedded with VIA V4 Eden processor 1.0GHz. User
don’t need to adjust the frequently and check speed of CPU.
3.6 System Memory
The HS-2613 provides one SO-DDRII socket at locations CN27. The
maximum capacity of the onboard memory is 1GB.
3.7 VGA Controller
The HS-2613 provides two connection methods of a VGA device.
CN25 offers an internal 10-pin CRT connector and CN6/CN9 are the
LVDS interface connectors onboard reserved for flat panel installation.
HS-2613 also provides DVI-D function (PCB v1.2 or above). There is
an option cable (291-13010040G)for this function use (CN10+CN30).
 CN16: 15-pin CRT Connector
PIN Description PIN Description
1 Red 2 Green
3 Blue 4 N/C
5 GND 6 GND
7 GND 8 GND
9 N/C 10 GND
11 N/C 12 SDA
13 HSYNC 14 VSYNC
15 SDC
1
515
10
611

11
 CN10/CN12: LVDS Interface Connector
PIN Description PIN Description
1 VLCD 2 VLCD
3 GND 4 GND
5 A0-/B0- 6 A0+/B0+
7 A1-/B1- 8 A1+/B1+
9 A2-/B2- 10 A2+/B2+
11 CLK1-/CLK2- 12 CLK1+/CLK2+
13 A3-/B3- 14 A3+/B3+
12
13 14
NOTE: LVDS cable should be produced very carefully. A0- & A0+ have to
be fabricated in twister pair (A1- & A1+, A2- & A2+ and so on)
otherwise the signal won’t be stable. Please set the proper voltage
of your panel using JP1 before proceeding on installing it.
 CN30: DVI SM Bus
PIN Description
1 SPD1
2 SPCLK1
2
1
 CN7: Inverter Power Connector
PIN Description
1 +12V
2 +12V
3 VCC
4 BK_EN
5 ENVDD
6 GND
1
6
NOTE: If use CN10 only, it just supports 24-bit single channel LVDS
panel; If you want to use 48-bit dual channel LVDS panel, please
use CN10 and CN12 combined.
The HS-2613 has an onboard jumper that selects the working voltage
of the flat panel connected to the system. Jumper JP1 offers two
voltage settings for the user.
 JP1: Panel Voltage Select
Options Settings
+3.3V (default) Short 1-2
+5V Short 2-3
1
3

12
3.8 IDE Drive Connector
CN11 is a 2.0-pitch 44-pin connector which support up to 2
ATA/33/66/100 IDE drives can be connected to the HS-2613 via CN11.
 CN11: IDE Connector
PIN Description PIN Description
1 Reset 2 GND
3 PDD7 4 PDD8
5 PDD6 6 PDD9
7 PDD5 8 PDD10
9 PDD4 10 PDD11
11 PDD3 12 PDD12
13 PDD2 14 PDD13
15 PDD1 16 PDD14
17 PDD0 18 PDD15
19 GND 20 N/C
21 PDREQ 22 GND
23 IOW# 24 GND
25 IOR# 26 GND
27 PIORDY 28 PR1PD1-
29 RPDACK- 30 GND
31 Interrupt 32 N/C
33 RPDA1- 34 PATA66
35 RPDA0- 36 RPDA2-
37 RPCS1- 38 RPCS3-
39 HDD Active 40 GND
41 VCC 42 VCC
43 GND 44 N/C
1
2
43
44
3.9 Serial ATA Connector
You can connect the Serial ATA device that provides you high speeds
transfer rates (150MB/sec.). If you wish to use RAID function, please
note that these two serial ATA connectors just support RAID0 and only
compatible with WIN XP.

13
 CN4: Serial ATA Connector
PIN Description
1 GND
2 SATATXP
3 SATATXN
4 GND
5 SATARXN
6 SATARXP
7 GND
17
3.10 Serial Port Connectors
The HS-2613 offers NS16C550 compatible UARTs with Read/
Receive 16-byte FIFO serial ports and four internal 10-pin headers
and one RS-422/485 connector.
 CN24/CN20/CN21/CN26: COM 1 ~ COM 4 Connector (5x2
Header)
PIN Description PIN Description
1 DCD 2 DSR
3 RXD 4 RTS
5 TXD 6 CTS
7 DTR 8 RI
9 GND 10 N/C
19
10 2
 CN18: RS-422/485 Connector (3x2 Header, COM 2)
PIN Description PIN Description
1 TX- 2 TX+
3 RX+ 4 RX-
5 GND 6 N/C
15
62
NOTE: The terminal resistance of RX & TX is set at 180 Ω .
 CN25: COM 2 use RS-232 or RS-422/485 Select
Options Settings
RS-232 (default) Open
RS-485 by Auto (*1) Short 1-2, 3-4, 5-7, 8-10
RS-485 by –RTS (*-1) Short 1-2, 3-4, 7-9, 8-10
RS-422/485 Full Duplex (*2) Short 1-2, 3-4, 6-8
19
10 2

14
NOTE: *1: 2-wires RS-485 function
*2: 4-wires point-to-point full duplex function
4-wires point-to-point full duplex RS-422/485
Typical RS-485 2-wires Mutildrop Network
3.11 Ethernet Connector
The HS-2613 provides two RJ-45 connectors for 10/100 Based LAN.
Please refer to the following for its pin information.
When installs OS, this driver namely can automatically install. User
does not need to renewal.
 CN13/CN14: RJ-45 Connector
PIN Description PIN Description
1 TCT 10 TX+
2 TX- 11 RX+
3 RX- 12 N/C
4 N/C 13 N/C
5 N/C 14 RCT
6 Link LED 15 330Ωpull VCC3
7 ACT LED 16 330Ωpull VCC3
8 SHIELD 17 SHIELD
9 SHIELD 18 SHIELD
1
8