Boser HS-6011L User manual

HS-6011
Pentium
®
-II-III-Celeron  BX L/VGA LAN
•PICMG Bus Full Size•All-in-one•CRT/Panel•RS-232/422/485•
•DMA33•WDT•DOC•USB•IrDA•LAN•PC/104•CTA•
•100MHz Bus•Pentium®-II-III-CeleronCPU at Face-Side•
HS-6011V
Pentium
®
-II-III-Celeron  BX L/VGA
•PICMG Bus Full Size•All-in-one•CRT/Panel•RS-232/422/485•
•DMA33•WDT•DOC•USB•IrDA•PC/104•CTA•
•100MHz Bus•Pentium®-II-III-CeleronCPU at Face-Side•
HS-6011L
Pentium
®
-II-III-Celeron  BX LAN
•PICMG Bus Full Size•All-in-one•RS-232/422/485•
•DMA33•WDT•DOC•USB•IrDA•LAN•PC/104•CTA•
•100MHz Bus•Pentium®-II-III-CeleronCPU at Face-Side•
HS-6011P
Pentium
®
-II-III-Celeron  BX ISB
•PICMG Bus Full Size•All-in-one•RS-232/422/485•
•DMA33•WDT•DOC•USB•IrDA•PC/104•CTA•
•100MHz Bus•Pentium®-II-III-CeleronCPU at Face-Side•

Copyrights
This manual is copyrighted and all rights are reserved. It is not allow any non
authorization in copied, photocopied, translated or reproduced to any electronic or
machine readable form in whole or in part without prior written consent from the
manufacturer.
In general, the manufacturer will not be liable for any direct, indirect, special,
incidental or consequential damages arising from the use of inability to use the
product or documentation, even if advised of the possibility of such damages.
The manufacturer keeps the rights in the subject to change the contents of this
manual without prior notices in order to improve the function design, performance,
quality and reliability. The author assumes no responsibility for any errors or
omissions, which may appear in this manual, nor does it make a commitment to
update the information contained herein.
Trademarks
BOSER is registered trademark of BOSER Technology Co., Ltd.
ISB is registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award International Inc.
All other trademarks, products and or product's name mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or registered
trademarks of their respective companies or owners.
© Copyright 1999
All Rights Reserved.
User Manual edition 1.7, Aug.24 2001

Contents •i
Contents
HS-6011 ......................................................................................................1
HS-6011V....................................................................................................1
HS-6011L ....................................................................................................1
HS-6011P....................................................................................................1
GENERAL INFORMATION .............................................................................3
1.1 MAJOR FEATURES .....................................................................................4
1.2 SPECIFICATIONS.........................................................................................5
1.3 DELIVERY PACKAGE...................................................................................7
HARDWARE INSTALLATION ........................................................................8
2.1 CAUTION OF STATIC ELECTRICITY.............................................................8
2.2 CAUTION ON UNPACKING AND BEFORE INSTALLATION .............................9
2.3 HS-6011’S LAYOUT.................................................................................10
2.4 QUICK LISTING OF JUMPERS ...................................................................11
2.5 QUICK LISTING OF CONNECTORS ............................................................12
2.6 JUMPER SETTING DESCRIPTION..............................................................13
2.7 SETTING THE BUS-CLOCK FREQUENCY ..................................................14
2.8 FREQUENCY MULTIPLIER SETTING..........................................................15
2.9 SETTING THE RTC CONFIGURATION.......................................................16
2.10 SYSTEM MEMORY DRAM .....................................................................16
2.11 ATX/AT POWER SELECT ......................................................................16
2.12 WATCH-DOG TIMER...............................................................................17
2.13 PCI VGA CONTROLLER ........................................................................19
2.14 DISKONCHIPADDRESS SETTING.......................................................19
2.15 LCD 3.3/5.0V POWER SELECT.............................................................20
2.16 MANUFACTURER’S DEFAULT SETTING ..................................................20
2.17 TEMPERATURE ALARM ..........................................................................20
2.18 RETENTION MECHANISM .......................................................................21
CONNECTION .................................................................................................22
3.1 POWER AND FAN CONNECTORS ............................................................22
3.2 IDE'S LED, KEY-LOCK AND RESET BUTTON ..........................................23
3.3 EXTRA SPEAKER CONNECTOR ................................................................24
3.4 PCI E-IDE DRIVE CONNECTOR ..............................................................25
3.5 PS/2 POWER ON/OFF CONTROL ..........................................................27

ii •Contents
3.6 PARALLEL PORT CONNECTOR.................................................................27
3.7 THE FLOPPY DISK DRIVE CONNECTOR ...................................................28
3.8 SERIAL PORTS CONNECTORS .................................................................29
3.9 KEYBOARD CONNECTORS .......................................................................31
3.10 PS/2 MOUSE 6-PIN MINI-DIN CONNECTOR .........................................31
3.11 VGA-CRT CONNECTOR .......................................................................32
3.12 FLAT-PANEL CONNECTOR .....................................................................33
3.13 IR CONNECTOR .....................................................................................35
3.14 USB PORT CONNECTOR.......................................................................35
3.15 PC/104 BUS CONNECTION ...................................................................36
3.16 FAST ETHERNET CONNECTOR ..............................................................38
3.17 ATX POWER CONTROLLER CONNECTOR .............................................39
AWARD BIOS SETUP....................................................................................40
4.1 MAIN MENU ..............................................................................................41
4.2 STANDARD CMOS SETUP.......................................................................42
4.3 BIOS FEATURES SETUP..........................................................................43
4.4 CHIPSET FEATURES SETUP .....................................................................44
4.5 INTEGRATED PERIPHERALS .....................................................................45
4.6 POWER MANAGEMENT SETUP.................................................................46

3
Chapter-1
General Information
The HS-6011 is a bus-100MHz Intel®BX chipset design PICMG bus
Pentium®II-III-CeleronIndustrial Single Board (I.S.B.) CPU card with features
combine together to make it an ideal all-in-one industrial single board computer,
enhanced I/O effects with VGA interface supports LCD Display panel and CRT
Monitor on-board.
The HS-6011 also provides one set of PC/104 bus for 8/16-bit industrial
application with based on PC/104 standard bus.
With onboard DMA33 of mode 4 to IDE drive interface architecture, the HS-6011
supports with maximum 33.3 MB/sec in data transfer rating to 4 pieces IDE drive
connection. Design with Intel®82443BX and 82371EB core logic chipset, the
HS-6011 supports all series Pentium®II-III-Celeronoperating at 233 ~ 650MHz.
The on-board C&T®69000 VGA chipset supports up to 1280 x 1024 256 colors
display resolution with on-chip 2MBytes memory, and it provides both VGA CRT
Monitor and LCD Panel display connection.
The advanced PICMG bus add-on connection of HS-6011 allows user could
easily obtain both ISA's 16-bit and PCI's 32-bit full set signals from a full size
PICMG slot for suitable plug into system with 8/16/32-bit ISA and-or PCI slots
operating. The HS-6011 provides with two pieces 168-pin DIMM sockets support
up to 1.0GBytes of main system memory.
A single Flash chip holds the system BIOS, and you can easy update the Flash
BIOS by the Utility Update. Advanced USB and IR ports also provide for faster
and easily in data transmission. You can also use the DOS version of the
"DiskOnChip" socket by issuing commands from the DOS prompt without the
necessity of other software supports up to 144MB.
If a non-expect program cause halts, the onboard WDT Watch-Dog Timer will
automatically reset the CPU or generate an interrupt. The watchdog is designed
with hardware only and doesn’t need any arithmetical functions of a real-time
clock chip. This ensures the reliability in an unmanned or standalone system.

4
1.1 Major Features
 One axial-horizontal type Slot-1 socket at face-side for Intel®
Pentium®II-III-Celeron233〜650 MHz Processors.
 Intel®82443 BX chipset.
 PICMG add-on bus with on-board PC/104 bus connector for
8/16-bit supported.
 Two pieces DIMM sockets supports DRAM up to 1.0 GB.
 Two fast PCI DMA33-IDE connector support four IDE drives
include large size hard disks, CD-ROM, tape backup etc.
 PnP I/O address & IRQ selection.
 Two high-speed RS-232 serial ports support 16C550 UART with
16-byte FIFO. One port provides RS-422/485 selection.
 One enhanced bi-directional parallel port, supports SPP/EPP/ECP.
 On board PS/2 Keyboard and PS/2 Mouse connector.
 On board W83977 super I/O.
 On-board C&T®69000 SVGA adapter with on-chip 2MBytes
memory supports VGA LCD Panel and CRT Monitor display.
 On board Intel®82558 100-Based Network.
 “DiskOnChipTM” Socket supported memory size up to 72 MB.
 On-board two USB ports and one IrDA port.
 Build-in one industrial WDT Watch-Dog-Timer.
 AWARD Y2K PnP Flash BIOS.
 Hardware Temperature Alarm
*It will be a Warning “beep” come out if the CPU’s temperature reached
60℃. And it will stop as the CPU’s temperature going down below 60℃
again.

5
1.2 Specifications
 CPU: One piece Intel®Pentium®II-III-Celeron233/ 266/ 300/ 333/
400/450/500/650MHz.
 Bus interface: PICMG bus, comply with ISA and PCI slot One
on-board PC/104 bus connector.
 Chipset: Intel®82443 BX bus-100MHz chipset.
 Data bus: 64-bit
 Processing ability: 64-bit
 C&T®VGA Controller: C&T® 69000 VGA, on-chip 2 MB memory
included, supports up to 1280x1024 256 colors VGA modes
resolution. Also provides one 50-pin LCD Panel connector, one
internal 10-pin VGA-CRT connector.
 PCI Enhanced IDE Interfaces: Total four IDE drives supports with
Mode 3 & 4 DMA33 function provides transfer rate up to 33.3MB/sec.
 RAM memory: Two pieces 168-pin DIMM sockets supports up to
1.0 GBytes.
 Cache memory: Slot-1 socket supports Intel's
Pentium®II-III-CeleronCPU with build-in 512KB Pipeline burst
cache memory.
 Floppy disk drive interface: Supports up to two floppy disk drives.
 LAN: Intel® 82558 supports 100-Based.
 Parallel port: Supports SPP/ECP/EPP.
 Serial ports: Two RS-232 ports with 16-byte FIFO 16C550 UART.
One port provides RS-422/485 selection.
 BIOS: AWARD Y2K PnP Flash BIOS.
 WDT Watchdog timer: Periods set 1, 2, 10, 20 , 110 or 220
seconds, activity trigger with Reset or NMI.
 DMA channels: 7

6
 Temperature Alarm: Hardware monitoring.
 Interrupt levels: 15
 Keyboard: 6-pin mini-DIN connector or 5-pin header.
 Mouse: 6-pin mini-DIN connector support PS/2 type mouse.
 USB: Supports 2 USB header.
 IR interface: Supports one lrDA TX/RX header.
 Flash memory Disk: Socket for DiskOnChip™ (DOC).
 Fuse: Automatically resumes polyswitch resettable fuse.
 Extra Power: Provides one 4-PIN extra DC +5V/+12V power
connector.
 CMOS: DS12B887 or equivalent device.
 Power voltage requested: +5V, +12V and -12V.
 Maximum Power Consumption: +5V@5A(350MHz PII),
+12V@20mA,
-12V@20mA.
 Operating temperature: 0-55°C (CPU need cooler).
 Board size: 7.3"(L) x 4.8" (W) (185mm x 122mm).
The HS-6011 provides with VGA Interface to LCD and Monitor, IDE-DMA33,
WDT, DOC, USB, IrDA and LAN etc.
The HS-6011V provides with all function but without LAN.
The HS-6011L provides with all function but without VGA.
The HS-6011P provides with all function but without VGA and without LAN.

7
1.3 Delivery Package
The delivery package of HS-6011 includes all following items:
 One HS-6011 Industrial Single Board
 One Printer Port Bracketed Flat Cable
 One COM Port Bracketed Flat Cable
 Two IDE port Flat Cable
 One FDD port Flat Cable
 One PS/2 to Standard DIN type Keyboard Transfer Cable
 Utility Diskette
 User’s Manual
 5 pin ATX Power Connector Cable
Please contact with your dealer if any of these items are missing or
damaged when purchasing. And please keep all parts of the
delivery package with packing materials in case of you want to ship
or store the product in feature.

8
Chapter-2
Hardware Installation
This chapter provides the information on how to install the hardware
of HS-6011. At first, please follow up sections 1.3, 2.1 and 2.2 in
check the delivery package and carefully unpacking. Following
after, the jumpers setting of switch, watchdog timer and the
DiskOnChipaddress selection etc.
2.1 Caution of Static Electricity
The HS-6011 has been well package with an anti-static bag in
protect its sensitive computer components and circuitry from the
damage of static electric discharge.
Note: DO NOT TOUCH THE BOARD OR ANY OTHER
SENSITIVE COMPONENTS WITHOUT ALL NECESSARY
ANTI-STATIC PROTECTION.
You should follow the steps as following to protect the board in
against the static electric discharge whenever you handle the
board:
1. Please use a grounding wrist strap on whoever needs to handle
the HS-6011. Well clip the ALLIGATOR clip of the strap to the end
of the shielded wire lead from a grounded object. Please put on
and connect the strap before handle the HS-6011 for harmlessly
discharge any static electricity through the strap.
2. Please use anti-static pad for put any components or parts or
tools on the pad whenever you work on them outside the
computer. You may also in use the anti-static bag instead the
pad. Please ask from your local supplier in help up your
necessary parts on anti-static requirement.

9
2.2 Caution on Unpacking and Before Installation
First of all, please follow with all necessary steps of section 2.1 in
protection the HS-6011 from electricity discharge. With refer to
section 1.3, please check the delivery package again with following
steps:
1.Unpacking the HS-6011, keep well storage of all packing material,
manual and diskette etc. if has.
2.Is there any components lose or drop from the board? DO NOT
INSTALL IF HAPPENED.
3.Is there any visual damaged of the board? DO NOT INSTALL IF
HAPPENED.
4.Well check from your optional parts (i.e. CPU, SRAM, DRAM,
ROM-Disk etc.) for completed setting all necessary jumpers
setting to jumper pin-set and CMOS setup correctly. Please also
reference to all information of jumpers setting in this manual.
5.Well check from your external devices (i.e. Add-On-Card, Driver
Type etc.) for completed add-in or connection and CMOS setup
correctly. Please also reference to all information of connector
connection in this manual.
6.Please keep all necessary manual and diskette in a good
condition for your necessary re-installation if you change your
Operating System or whatever needs.

10
2.3 HS-6011’s Layout

11
2.4 Quick Listing of Jumpers
JP1 RESET ............................................................................ P.14
JP2 BUS CLOCK SELECT ........................................................ P.26
JP4 PANEL VOLTAGE SELECT ................................................. P.19
JP5 CLOCK RATIO SELECT...................................................... P.14
JP6 AT/ATX POWER FUNCTION SELECT................................. P.14
JP7 CPU TEMPERATURE ALARM ............................................ P.15
JP8 RS-422/485 RECEIVER ENABLED/DISABLED SELECT ........ P.27
JP9 RS-422/485 TRANSCEIVER ENABLED/DISABLED SELECT .. P.17
JP10(1-4) DISKONCHIP ADDRESS SELECT ....................................... P.29
JP10(5-10) WATCH-DOG TIMER PERIOD SELECT ............................... P.30
JP11 RS-232 OR RS-422/485 SELECT ................................... P.29
JP12 RS-232 OR RS-422/485 SELECT .................................... P.30
JP13 CLEAR CMOS ................................................................ P.29
JP14 WATCH-DOG TIMER ACTIVE TYPE SELECT ........................ P.30
JP16 LAN ENABLED/DISABLED SELECT ................................... P.29
JP17 VGA ENABLED/DISABLED SELECT.................................... P.30

12
2.5 Quick Listing of Connectors
CN1 KEYLOCK CONNECTOR.................................................... P.21
CN2 SPEAKER CONNECTOR.................................................... P.18
CN3 IDE LED........................................................................ P.19
CN4 3PIN FAN CONNECTOR................................................... P.20
CN5 2PIN ATX POWER CONNECTOR....................................... P.18
CN6 5PIN KEYBOARD CONNECTOR ......................................... P.19
CN7 4PIN POWER CONNECTOR............................................... P.14
CN8 PRIMARY IDE CONNECTOR ............................................. P.14
CN9 SECONDARY IDE CONNECTOR......................................... P.23
CN10 PANEL CONNECTOR........................................................ P.31
CN11 5PIN ATX POWER CONNECTOR ....................................... P.31
CN12 PARALLEL CONNECTOR ................................................... P.22
CN13 RS-422/485 CONNECTOR (5X2 HEADER) ........................ P.29
CN14 PC/104 64PIN CONNECTOR ............................................ P.24
CN15 PC/104 40PIN CONNECTOR ............................................ P.18
CN16 FLOPPY CONNECTOR ...................................................... P.26
CN17 COM1 (5X2 HEADER) ..................................................... P.25
CN18 COM2 (5X2 HEADER) ..................................................... P.30
CN19 CRT CONNECTOR (5X2 HEADER) .................................... P.25
CN20 USB CONNECTOR .......................................................... P.26
CN21 IRDA CONNECTOR ......................................................... P.25
CN22 RJ45 CONNECTOR.......................................................... P.24
CN23 COM1 (DB9).................................................................. P.24
CN24 PS/2 6PIN MINI DIN MOUSE CONNECTOR......................... P.24
CN25 CRT CONNECTOR (DB15) .............................................. P.25
CN26 COM2 (DB9) ................................................................ P.24
CN27 PS/2 6PIN MINI DIN KEYBOARD CONNECTOR .................. P.24
CN28 2PIN FAN CONNECTOR .................................................. P.24

13
2.6 Jumper Setting Description
A jumper pin-set is ON as a shorted circuit with a plastic cap
inserted over two pins. A jumper pin-set is OFF as a open circuit
with a plastic cap inserted over one or no pin(s) between pins. The
below figure 2.2 shows the examples of different jumper pin-set
setting as ON or OFF in this manual.
Figure 2.2
All jumper pin-set already has its default setting with the plastic cap
inserted as ON, or without the plastic cap inserted as OFF. The
default setting may reference in this manual with a " * " symbol in
front of the selected item.

14
2.7 Setting the Bus-Clock Frequency
The HS-6011 provides all necessary by jumper setting in using
Bus-Clock frequency as the system bus clocking with JP2 setting as
following:
 Bus-Clock Frequency Setting of JP2:
Bus-Clock Frequency JP2
* 100MHz OFF
66MHz ON

15
2.8 Frequency Multiplier Setting
The HS-6011 provides JP5 for define the selection of the Frequency
Multiplier value of system bus to processor core in following table:
 Frequency Multiplier Setting of JP5:
Frequency Multiplier: System Clock
JP5 ON JP5 OFF
System Bus to
Processor Core 7-8 5-6 3-4 1-2 66 * 100
3x ON ON OFF ON 200 300
4x ON ON ON OFF 266 400
5x ON ON OFF OFF 333 500
2.5x ON OFF ON ON 166 250
* 3.5x ON OFF OFF ON 233 * 350
4.5x ON OFF ON OFF 300 450
5.5x OFF ON OFF OFF 366 550
6x ON OFF ON ON 400 600
6.5x OFF OFF ON ON 430 650
7x ON OFF OFF ON 460 700
7.5x OFF OFF OFF ON 500 750
8x ON OFF ON OFF 530 800
The bus-clock is setting by JP2 and JP5 The default setting is for Intel
Pentium®II 350MHz processor. If the bus Frequency not match
processor frequency, the system will be unstable.

16
2.9 Setting the RTC Configuration
The HS-6011 provides a setting for the selection of the RTC Clear
Jumper by JP13 setting as following:
 CMOS Setting of JP13: (DS12B887)
CMOS Clear Jumper JP13
Normal * OFF
Clear CMOS ON
2.10 System Memory DRAM
The HS-6011 provides a wide range on-board DRAM memory by
two pieces DIMM sockets (DIMM-1, DIMM-2) request the access
time should meet PC-100 standard.. The maximum capacity of the
on board memory is 1.0GBytes.
See the figure on section 2.3 for get the identifying the banks.
2.11 ATX/AT Power Select
The HS-6011 provides a selection by a three-pin jumper JP6 for setting
the power supply type in using.
 ATX/AT Power Select Setting of JP6:
Power Supply In Using JP6
ATX Power Supply 2-3
AT Power Supply * 1-2

17
2.12 Watch-Dog Timer
There are three access cycles of Watch-Dog Timer as Enable,
Refresh and Disable. The Enable cycle should proceed by READ
PORT 443H. The Disable cycle should proceed by READ PORT
045H. A continue Enable cycle after a first Enable cycle means
Refresh.
Once if the Enable cycle activity, a Refresh cycle is request before
the time-out period for restart counting the WDT Timer's period.
Otherwise, it will assume that the program operation is abnormal
when the time counting over the period preset of WDT Timer. A
System Reset signal to start again or a NMI cycle to the CPU comes
if over.
The JP14 is using for select the active function of watch-dog timer in
disable the watch-dog timer, or presetting the watch-dog timer
activity at the reset trigger, or presetting the watch-dog timer activity
at the NMI trigger.
 JP14 : Watch-Dog Active Type Setting
JP14 DESCRIPTION
*2-3 System Reset
1-2 Active NMI
OFF disable Watch-dog timer
 JP10 ( pin 5-6, 7-8, 9-10 ) : WDT Time - Out Period
WD2 WD1 WD0
PERIOD
5 – 6 7 – 8 9 – 10
*1 sec ON ON ON
2 sec OFF ON ON
10 sec ON OFF ON
20 sec OFF OFF ON
110 sec ON ON OFF
220 sec OFF ON OFF

18
The Watch-dog timer is disabled after the system Power-On. The
watch-dog timer can be enabled by a Enable cycle with reading the
control port (443H), a Refresh cycle with reading the control port
(443H) and a Disable cycle by reading the Watch-dog timer disable
control port (045H). After a Enable cycle of WDT, user must
constantly proceed a Refresh cycle to WDT before its period setting
comes ending of every 1, 2, 16 or 256 seconds which pre-setting by
JP10 ( PIN 5-6, 7-8 ). If the Refresh cycle does not active before
WDT period cycle, the on board WDT architecture will issue a Reset
or NMI cycle to the system.
The Watch-Dog Timer is controlled by two I/O ports.
443H I/O Read The Enable cycle.
443H I/O Read The Refresh cycle.
045H I/O Read The Disable cycle.
The following sample programs showing how to Enable, Disable
and Refresh the Watch-dog timer:
WDT_EN_RF EQU 0443H
WDT_DIS EQU 0045H
WT_Enable PUSH AX ; keep AX DX
PUSH DX
MOV DX,WDT_EN_RF ; enable the WDT
IN AL,DX
POP DX ; get back AX, DX
POP AX
RET
WT_Rresh PUSH AX ; keep AX, DX
PUSH DX
MOV DX,WDT_ET_RF ; refresh the WDT
IN AL,DX
POP DX ; get back AX, DX
POP AX
RET
WT_DISABLE PUSH AX
PUSH DX
MOV DX,WDT_DIS ; disable the WDT
IN AL,DX
POP DX ; get back AX, DX
POP AX
RET