Boser HS-4010 User manual

HS-4010
Half 486 Little Board
10 Base-T Network, Flat Panel, VGA Control.

Copyrights
This manual is copyrighted and all rights are reserved. It is not allow any non
authorizationincopied,photocopied,translatedorreproducedto anyelectronic
or machine readable form in whole or in part without prior written consent from
the manufacturer.
In general, the manufacturer will not be liable for any direct, indirect, special,
incidentalorconsequentialdamagesarising fromtheuseofinabilitytousethe
product or documentation, even if advised of the possibility of such damages.
The manufacturer keeps the rights in the subject to change the contents of this
manual without prior notices in order to improve the function design,
performance, quality and reliability. The author assumes no responsibility for
any errors or omissions, which may appear in this manual, nor does it make a
commitment to update the information contained herein.
Trademarks
BOSER is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
ISB is a registered trademark of BOSER Technology Co., Ltd.
All other trademarks, products and or product's name mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or
registered trademarks of their respective companies or owners.
© Copyright 1999
All Rights Reserved.
User Manual edition 1.1, Aug.24.2001

Contents?i
CONTENTS
HS-4010...................................................................................................................1
GENERAL INFORMATION.........................................................................................3
1.1 MAJOR FEATURES..................................................................................................4
1.2 SPECIFICATIONS ......................................................................................................5
1.3 DELIVERY PACKAGE..............................................................................................7
HARDWARE INSTALLATION...................................................................................8
2.1 CAUTION OF STATIC ELECTRICITY........................................................................8
2.2 CAUTION ON UNPACKING AND BEFORE INSTALLATION......................................9
2.3 HS-4010’S LAYOUT............................................................................................10
2.4 QUICK LISTING OF JUMPERS.................................................................................11
2.5 QUICK LISTING OF CONNECTORS ........................................................................11
2.6 JUMPER SETTING DESCRIPTION............................................................................13
2.7 SETTING THE CPU OF HS-4010........................................................................14
2.8 SYSTEM MEMORY DRAM...................................................................................16
2.9 WATCH-DOG TIMER..............................................................................................16
2.12 VGA CONTROLLER............................................................................................18
2.13 DISKONCHIP?ADDRESS SETTING..................................................................19
CONNECTION..............................................................................................................20
3.1 THE FLOPPY DISK DRIVE CONNECTOR...............................................................20
3.2 PCI E-IDE DRIVE CONNECTOR..........................................................................21
3.3 PARALLEL PORT CONNECTOR............................................................................22
3.4 SERIAL PORTS CONNECTORS.............................................................................23
3.5 KEYBOARD CONNECTOR.....................................................................................24
3.6 POWER'S LED, FAN AND KEY-LOCK CONNECTORS......................................24
3.7 MOUSE CONNECTOR............................................................................................24
3.8 PS/2 MOUSE IRQ12 SELECTION CONNECTOR................................................25
3.9 VGA CONNECTOR................................................................................................25
3.11 FAST ETHERNET CONNECTOR..........................................................................26
3.12 FLAT-PANEL CONNECTOR................................................................................27
3.13 CONNECTIONS FOR FOUR STANDARD LCDS...................................................28
AWARD BIOS SETUP...............................................................................................34

ii ?Contents
4.1 MAIN MENU...........................................................................................................35
4.2 STANDARD CMOS SETUP..................................................................................36
4.3 BIOS FEATURES SETUP......................................................................................37
4.4 CHIPSET FEATURES SETUP..................................................................................38
4.5 POWER MANAGEMENT SETUP............................................................................39
4.6 PNP/PCI CONFIGURATION SETUP.....................................................................40
4.7 INTEGRATED PERIPHERAL SETUP........................................................................41
4.8 PANEL TYPE SELECT............................................................................................42
A BRIEF BROWSE OF 10 BASE-T LAN RTL-8019’S INSTALLATION
SOFTWARE..................................................................................................................43

3
Chapter-1
General Information
The HS-4010 is an all-in-one half size industrial single board with
design in Novell NE2000 compatible 16 bits ISA bus Ethernet, provides
10 BASE-T for directly network automation demand.
Supports for various 40-133 MHz 80486SX/DX/DX2/DX4, 5x86 CPUs
with 32-bit data bus and processing ability. Up to 64MB RAM by 72-pin
SIMM supported. Provides "DiskOnChip?" socket supported memory
size up to 72 MB.
Desinged with the on board 1MB memory VGA architecture, supports
direct interface to color and monochrome Single Drive (SD) and Dual
Drive (DD) STN, TFT & EL panels and resolutions up to 1024x768 256
colors to CRT monitor.
The HS-4010 support completed with all necessary I/O for industrial
application. Two PCI enhanced IDE ATA-2 IDE drivers; supports up to
two floppy disk drivers; provide two high speed serial RS-232 ports port
with compatible to 16C550 UART with 16-byte FIFO; one enhanced
bi-directional parallel port which support SPP/EPP/ECP. The board
also provides keyboard and PS/2 mouse connector.

4
1.1 Major Features
?? 80486SX/DX/DX2/DX4, 5x86 CPU supported.
?? ALi 1487/1489 chipset.
?? Supports DRAM up to 64 MB.
?? Fast PCI enhanced IDE controller supports two IDE drives.
?? Two high-speed serial RS-232 ports (supports 16C550 UART with
16-byte FIFO).
?? One enhanced bi-directional parallel port supports SPP/EPP/ECP.
?? Keyboard and PS/2 Mouse connector.
?? On-board SMSC 37C669 Super I/O.
?? On-board 32 bit PCI-BUS VGA/ Panel controller.
?? "DiskOnChip™" Socket Supported Memory Size up to 72 MB.
?? On-board 16 bit ISA bus Ethernet, Novell NE2000 compatible.

5
1.2 Specifications
?? CPU: 80486SX/DX/DX2/DX4/5X86.
?? Bus interface:ISA bus
?? Chipset:ALi 1487/1489
?? Data bus:32-bit
?? Processing ability: 32-bit
?? PCI Flat Panel / VGA Controller:VGA Chipset with 1 MB
memoryinterfacetocolorandmonochromeSingleDrive(SS)
and Dual Drive (DD) STN, TFT & EL panels. Support CRT
resolutions up to 1024x768 256 colors.
?? PCI Enhanced IDE interfaces:Supports up to twoenhanced
IDE ATA-2).
?? RAM memory: Up to 64MB, uses two 72-pin SIMM sockets.
?? Cache memory: On board 128KB 2nd level cache.
?? Floppy disk drive interface:Supports up to two floppy disk
drives.
?? Parallel port:One parallel port supports SPP/ECP/EPP.
?? Serial port:Two RS-232 ports supports 16C550 UART with
16-byte FIFO.
?? BIOS:AWARD flash BIOS.
?? Watchdog timer:Hardware circuit can be set by 1, 2, 10, 20,
110, or 220 seconds period Reset or NMI was generated
when CPU did not periodically trigger the timer.
?? Ethernet:Realtek RTL8019, 16 bit ISA bus Ethernet, Novell
NE2000 compatible.
?? Keyboard / Mouse connector:8-pin connector supports
standard PC/AT keyboard and a PS/2 mouse.
?? ISA bus:Standard ISA bus
?? Flash memory Disk:Reserved socket for "DiskOnChip™",

6
support up to 72MB Flash memory disk.

7
?? CMOS:Real-time clock/calendar and battery backup by
DS12B887 or equivalent device.
?? Power supply voltage:±5V±5%, ±12V±5%.
?? Max. Power requirement:+5V @2.5A
?? Operating temperature:0-55°C (CPU need cooler).
?? Board size:8" (L) x 5.75" (W) (203mm x 146mm).
1.3 Delivery Package
The delivery package of HS-4010 includes all following items:
?? HS-4010 Industrial Single Board
?? Printer port Flat Cable
?? IDE port Flat Cable
?? FDD port Flat Cable
?? Serial port Cable
?? PS/2 Mouse and Keyboard Transfer Cable
?? Utility Diskette
?? User’s Manual
Please contact with your dealer if any of these items are
missing or damaged when purchasing. And please keep all
parts of the delivery package with packing materials in case of
you want to ship or store the product in feature.

8
Chapter-2
Hardware Installation
This chapter provides the information on how to install the
hardware of HS-4010. At first, please follow up sections 1.3, 2.1
and 2.2 in check the delivery package and carefully unpacking.
Following after, the jumpers setting of switch, watchdog timer,
and the DiskOnChip?address selection.
2.1 Caution of Static Electricity
The HS-4010 has been well package with a anti-static bag in
protect its sensitive computer components and circuitry from
the damage of static electric discharge.
Note: DO NOT TOUCH THE BOARD OR ANY OTHER
SENSITIVE COMPONENTS WITHOUT ALL
NECESSARY ANTI-STATIC PROTECTION.
You should follow the steps as following to protect the board in
against the static electric discharge whenever you handle the
board:
1. Please use a grounding wrist strap on whoever needs to
handle the HS-4010. Well clip the ALLIGATOR clip of the
strap to the end of the shielded wire lead from a grounded
object. Please put on and connect the strap before handle the
HS-4010 for harmlessly discharge any static electricity
through the strap.
2. Please use anti-static pad for put any components or parts or
tools on the pad whenever you work on them outside the
computer. You may also in usethe anti-static bag instead the