Boser HS-6050 User manual

HS-6050
Socket 370 133MHz FSB PICMG Bus
Industrial Single Board Computer
•Full Size•All-in-One•CRT•133MHz FSB•
•ATA/33/66/100•Dual LAN•Audio•
•RS-232/422/485•PC/104•IrDA•USB•
•DOC•WDT•H/W Monitor•
•PICMG Bus Industrial Single Board computer•

Copyright Disclaimers
The accuracy of contents in this manual has passed thorough checking and review
before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is
not liable for any infringements of patents or other rights resulting from its use. The
manufacturer will not be responsible for any direct, indirect, special, incidental
or consequential damages arising from the use of this product or
documentation, even if advised of the possibility of such damage(s).
This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation,
and storage of any form and means (i.e., electronic, mechanical, photocopying,
recording) of this document, in whole or partly, is prohibited, unless granted
permission by BOSER Technology Co., Ltd.
BOSER Technology Co., Ltd. reserves the right to change or improve the
contents of this document without due notice. BOSER Technology Co., Ltd.
assumes no responsibility for any errors or omissions that may appear in this
manual, nor does it make any commitment to update the information contained
herein.
T
T
Tr
r
ra
a
ad
d
de
e
em
m
ma
a
ar
r
rk
k
ks
s
s
BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
AMI is a registered trademark of AMI Software, Inc.
Award is a registered trademark of Award International Inc.
All other trademarks, products and or product names mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or
registered trademarks of their respective companies or owners.
© Copyright 2002 BOSER Technology Co., Ltd.
All Rights Reserved.
Edition 1.1, December 05, 2002

Table of Contents
Chapter 1 General Description ..................................1
1.1 Major Features....................................................................... 2
1.2 Specifications ........................................................................ 3
1.3 Board Dimensions................................................................. 4
Chapter 2 Unpacking ..................................................5
2.1 Opening the Delivery Package............................................. 5
2.2 Inspection............................................................................... 5
Chapter 3 Hardware Installation ..............................7
3.1 Before Installation ................................................................. 7
3.2 Board Layout ......................................................................... 8
3.3 Jumper List ............................................................................ 9
3.4 Connector List ....................................................................... 9
3.5 Configuring the CPU ........................................................... 10
3.6 System Memory ................................................................... 10
3.7 DiskOnChipAddress Setting .......................................... 10
3.8 VGA Controller .................................................................... 12
3.9 PCI E-IDE Drive Connector................................................. 13
3.10 Floppy Disk Drive Connector ............................................. 14
3.11 Serial Port Connectors ....................................................... 15
3.12 Parallel Connector............................................................... 16
3.13 Ethernet Connector............................................................. 17
3.14 IrDA Connector .................................................................... 17
3.15 USB Connector .................................................................... 18
3.16 CMOS Data Clear................................................................. 18
3.18 Power and Fan Connectors................................................ 18
3.19 Keyboard Connectors......................................................... 19
3.20 PS/2 Mouse Connector ....................................................... 20
3.21 System Front Panel Connectors........................................ 21
3.22 Watchdog Timer .................................................................. 21
3.23 PC/104 Connectors ............................................................. 24
3.24 Audio Connector ................................................................. 26
Chapter 4 AMI BIOS Setup .....................................27
4.1 Starting Setup ...................................................................... 27
4.2 Using Setup.......................................................................... 28
4.3 Main Menu ............................................................................ 29
4.4 Standard CMOS Setup ........................................................ 30

4.5 Advanced CMOS Setup ...................................................... 31
4.6 Advanced Chipset Setup .................................................... 32
4.7 Power Management Setup ................................................. 33
4.8 PCI / Plug and Play Setup................................................... 34
4.9 Peripheral Setup.................................................................. 35
4.10 Hardware Monitor Setup..................................................... 36
4.11 Auto-Detect Hard Disks ...................................................... 37
4.12 Change Supervisor/User Password .................................. 38
4.13 Auto Configuration with Optimal Settings ....................... 39
4.14 Optimal Configuration with Fail Safe Settings................. 40
4.15 Save Settings and Exit........................................................ 41
4.16 Exit Without Saving............................................................. 42
Chapter 4-1 Award BIOS Setup .................................43
4.1 Starting Setup ...................................................................... 43
4.2 Using Setup.......................................................................... 44
4.3 Main Menu ............................................................................ 45
4.4 Standard CMOS Features ................................................... 46
4.5 Advanced BIOS Features ................................................... 47
4.6 Advanced Chipset Features............................................... 48
4.7 Integrated Peripherals ........................................................ 49
4.8 Power Management Setup ................................................. 50
4.9 PnP/PCI Configurations...................................................... 51
4.10 PC Health Status ................................................................. 52
4.11 Load Fail-Safe Defaults....................................................... 53
4.12 Load Optimized Defaults .................................................... 54
4.13 Set Supervisor/User Password.......................................... 55
4.14 Save & Exit Setup ................................................................ 56
4.15 Exit Without Saving............................................................. 57
Chapter 5 Software Utilities.....................................59
5.1 IDE and Audio Driver Installation ...................................... 59
5.1.1 VIA VT82C686B AGP Bus Driver Installation ..................................59
5.1.2 VIA IDE Tool Installation............................................................................64
5.1.3 Audio Driver Installation..........................................................................69
5.2 LAN Driver Installation for WIN95 & WIN98 ...................... 72
5.3 LAN Driver Installation for WIN NT4.0............................... 78

Safety Instructions
Integrated circuits on computer boards are sensitive to static electricity.
To avoid damaging chips from electrostatic discharge, observe the
following precautions:
 Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
 Before handling a board or integrated circuit, touch an unpainted portion
of the system unit chassis for a few seconds. This helps to discharge any
static electricity on your body.
 Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components. Fasten the ALLIGATOR
clip of the strap to the end of the shielded wire lead from a grounded
object. Please wear and connect the strap before handle the HS-6050 to
ensure harmlessly discharge any static electricity through the strap.
 Please use an anti-static pad when putting down any components or
parts or tools outside the computer. You may also use an anti-static bag
instead of the pad. Please inquire from your local supplier for additional
assistance in finding the necessary anti-static gadgets.
NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC
PROTECTION.

This Page is intentionally left blank.

1
Chapter 1
General Description
The HS-6050 is a 133MHz FSB VIA VT8601 chipset-based board
designed for PICMG Bus Intel®Celeron/Coppermine/Tualatin and VIA
C3 800MHz~1.3GHz CPU. These features combine and make the
HS-6050 an ideal all-in-one industrial single board computer.
Additional features include an enhanced I/O with 2 COM ports, dual
LAN and CRT interface.
Its onboard ATA/33/66/100 to IDE drive interface architecture allows
the HS-6050 to support data transfers of 33, 66 or 100MB/sec. to each
IDE drive connection. Designed with the VIA VT8601 core logic
chipset, the board supports Intel®Celeron/Coppermine/Tualatin and
VIA C3 800MHz~1.3GHz CPU. The 8601 integrated Trident 3D
supporting AGP Bus
For suitable installation into any size system with 8/16/32-bit ISA and/or
PCI slots operation, the board’s advanced PCI and ISA bus add-on
feature allows user to easily obtain both ISA's 16-bit and PCI's 32-bit
full set signals from a full-size PICMG slot. System memory is also
sufficient with the three DIMM sockets that can support up to 1.5GB.

2
Additional onboard connectors include an advanced USB and IrDA
ports providing faster data transmission, a DOS-compatible
DiskOnChipsocket with a maximum capacity of 288MB, and two
external RJ-45 connectors for 10/100 Based Ethernet use.
To ensure the reliability in an unmanned or standalone system, the
Watchdog Timer (WDT) onboard HS-6050 is designed with pure
hardware that does not need the arithmetical functions of a real-time
clock chip. If any program causes unexpected halts to the system, the
onboard Watchdog Timer (WDT) will automatically reset the CPU or
generate an interrupt to resolve such condition.
1.1 Major Features
The HS-6050 comes with the following features:
 Socket 370 for Intel®Celeron/Coppermine/Tualatin and VIA C3
800MHz~1.3GHz CPU
 VIA VT8601/VT86C686B system chipset
 Supports 66/100/133MHz FSB
 Three DIMM sockets with a max. capacity of 1.5GB
 VIA VT82C686B super I/O chipset
 Fast PCI ATA/33/66/100 IDE controller
 One RS-232 and one RS-232/422/485 serial ports
 PC/104 Bus connector
 VIA VT8601 CRT display controller
 Dual RealTek RTL8100 10/100 Based LAN
 AC97 3D audio controller
 DiskOnChipsocket supports memory sizes of up to 288MB
 Supports Hardware Monitor function

3
1.2 Specifications

CPU: Socket 370 for Intel®Celeron/Coppermine/Tualatin and VIA C3
800MHz~1.3GHz CPU
 Bus Interface: PICMG Bus
 Memory: Three DIMM sockets supporting up to 1.5GB
 Chipset: VIA VT8601/VT82C686B
 I/O Chipset: VIA VT82C686B
 VGA: VIA VT8601 integrated Trident 3D supporting AGP Bus
 IDE: Four IDE disk drives supporting ATA/33/66/100 and with transfer
rates of up to 33/66/100MB/sec.

FDD: Supports up to two floppy disk drives

Parallel: One enhanced bi-directional parallel port supporting
SPP/ECP/EPP
 LAN: Dual RealTek RTL8100 10/100 Based LAN
 Audio: AC97 3D audio controller supporting speaker out
 Serial Port: 16C550 UART-compatible RS-232/422/485 x 1 and RS-232
x 1 serial ports with 16-byte FIFO

PC/104: PC/104 connector for 16-bit ISA Bus

IrDA: One IrDA TX/RX header

USB: Two USB connectors

Keyboard: PS/2 6-pin Mini DIN or 5-pin connector

Mouse: PS/2 6-pin Mini DIN or 4-pin connector

DiskOnChip:DiskOnChipsocket supporting memory sizes of up to
288MB
 BIOS: AMI PnP Flash BIOS
 Watchdog Timer: Sets 1, 2, 10, 20, 110, 220 seconds, activity trigger
with Reset or NMI

CMOS: Battery backup

DMA Channels: 7

Interrupt Levels: 15

Operating Temperature: 0~60°C

Hardware Monitor: VIA VT82C686B

Board Size: 33.8 x 12.1 cm

4
1.3 Board Dimensions

5
Chapter 2
Unpacking
2.1 Opening the Delivery Package
The HS-6050 is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.
2.2 Inspection
After unpacking the board, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.
Integrated circuits will sometimes come out of their sockets during
shipment. Examine all integrated circuits, particularly the BIOS,
processor, memory modules, ROM-Disk, and keyboard controller chip
to ensure that they are firmly seated. The HS-6050 delivery package
contains the following items:

HS-6050 Board x 1
 Utility CD Disk x 1

ATA/100 IDE flat cable x 2
 FDD flat cable x 1

Printer cable with bracket x 1
 RS-232 COM Port cables with bracket x 1

8-pin USB split type cable with bracket x 1
 MIC/Audio 8-pin cable + 2 phone jacks with bracket x 1

Jumper Bag x 1
 User’s Manual
IMPORTANT: The default setting of JP1 is Short 1-2. Before you turn on
the power of your system, please check JP1 to Short 1-2 for
normal operation.

6
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.

7
Chapter 3
Hardware Installation
This chapter provides the information on how to install the hardware
using the HS-6050. This chapter also contains information related to
jumper settings of switch, watchdog timer, and the DiskOnChip
address selection etc.
3.1 Before Installation
After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to
take before you begin with your installation process.
1. Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper.
2. Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections on this chapter
for the detailed information on the connectors.
3. Keep the manual and diskette in good condition for future
reference and use.
4. The default setting of JP1 is Short 1-2. Before you turn on the
power of your system, please check JP1 to Short 1-2 for
normal operation.

8
3.2 Board Layout

9
3.3 Jumper List
Jumper Default Setting Setting
JP1 Clear CMOS: Normal Operation Short 1-2
JP4 WDT Active Type Setting: Disabled Open
JP5(1-4) DiskOnChip Address Select: D000 Short 1-2
JP5(5-10) WDT Timer Select: 1sec. Short 5-6, 7-8, 9-10
JP6 RS-232 or RS-422/485 Select: RS-232 Short 3-5, 4-6
JP7 RS-232 or RS-422/485 Select: RS-232 Short 3-5, 4-6
JP9 RS-422/485 Transceiver Enable/Disable Select:
Enable Short 1-2
JP10 RS-422/485 Receiver Enable/Disable Select:
Enable Short 1-2
3.4 Connector List
Connector Definition
CN1 5-pin Keyboard Connector
CN2 Front Panel Signal Connector
CN3 IrDA Connector
CN4 ATX Power Connector
CN5 5-pin ATX Power Controller
CN6 Primary IDE Connector
CN7 Secondary IDE Connector
CN9 USB 3 & 4
CN10 USB 1 & 2
CN11 COM 1 Connector
CN12 FDD Connector
CN13 COM 2 Connector
CN14 PC/104 64-pin Connector
CN15 CD_IN Connector
CN16 PC/104 40-pin Connector
CN17 Parallel Connector
CN18 LINE_IN Connector
CN19 Internal LAN 1 Connector
CN20 Internal LAN 2 Connector
CN21 4-pin Mouse Connector
CN22 RS-422/485 Connector
CN23 Dual RJ-45 Connector
CN24 6-pin Mini DIN Mouse Connector
CN25 VGA Connector
CN26 6-pin Mini DIN Keyboard Connector
. . . More on next page . . .

10
Connector Definition
CN27 COM 1 Connector (DB9)
DM1, 2, 3 168-pin DIMM Socket
FN1 FAN1 Connector
FN2 FAN2 Connector
JP8 Line Out/MIC In Connector
3.5 Configuring the CPU
The HS-6050 offers the convenience in CPU installation with its
auto-detect feature. After installing a new microprocessor onboard, the
HS-6050 automatically identifies the frequency and clock speed of the
installed microprocessor chip, thereby eliminating the need for user to
do additional CPU configuration or hardware settings related to it.
3.6 System Memory
The HS-6050 provides three DIMM sockets at locations DM1, DM2 and
DM3. The maximum capacity of the onboard memory is 1.5GB.
3.7 DiskOnChipAddress Setting
The DiskOnChipfunction allows the system to boot or operate
without a FDD or a HDD. DiskOnChipmodules may be formatted as
drive C or A. With DiskOnChip, user may also execute DOS
commands such as FORMAT, SYS, COPY, XCOPY, DISCOPY and
DISKCOMP etc.
The U18 location onboard the HS-6050 is the DiskOnChipmodule
socket. Jumper JP5 (1-4) assigns the starting memory address of the
installed module. If you have another memory device that has a similar
memory capacity with that of the DOC in your system, please set both
at different memory address mapping to avoid the mapping area
conflicts. Failing to do so will not make the HS-6050 and the additional
memory device function properly.
 JP5(1-4): DiskOnChipAddress Select
Address PINS 1-2 PINS 3-4
* D000 Short Short
D800 Open Short

11
3.7.1 Installing DiskOnChipModules
When installing a DiskOnChipmodule onto your board, please take
note of the following:
1. Orient yourself properly with the location of the DiskOnChip
socket. Try to locate the pin 1 location on your socket. Pin
numbers are usually printed on either the component side or the
solder side of your board.
2. Locate the Pin 1 location on your DiskOnChipmodule. More
often than not, Pin 1 can be found on the lower right corner of
the chip. Please refer to the diagram for the exact location.
3. Once you have figured out where the pin 1 locations are on both
chip and socket, align the module’s pins on an upright angle
against the socket. Using both thumbs, gently press the module
into the socket until all the pins are secured to their
designations.
Pin 1
Location
DiskOnChip
4. The installation is now complete and your module is now ready
for use.
NOTE: If you encounter difficulty installing your DiskOnChip
 module,
please consult a qualified technician or engineer to perform the
installation.

12
3.7.2 Removing DiskOnChipModules
When removing a DiskOnChipmodule from its socket, please take
note of the following:
1. Loosen the contact of the module from its socket using a
screwdriver.
2. Insert the screwdriver’s flat head into a gap on either end of the
socket. Do not insert the screwdriver head on either side where
the pins are located. Doing so might damage the pins in the
process.
3. Slowly lift the screwdriver handle upwards. This will disengage
the module from its socket.
NOTE: If you encounter difficulty removing your DiskOnChip
 module,
please consult a qualified technician or engineer to remove it for
you.
3.8 VGA Controller
The HS-6050 provides one connection method of a VGA device. CN25
offers a single standard CRT connector (DB15).
 CN25: CRT Connector
PIN Description PIN Description
1 Red 2 Green
3 Blue 4 N/C
5 GND 6 GND
7 GND 8 GND
9 N/C 10 GND
11 N/C 12 SDA
13 HSYNC 14 VSYNC
15 SCLK

13
3.9 PCI E-IDE Drive Connector
CN6, CN7 are standard 40-pin connector daisy-chain driver connector
serves the PCI E-IDE drive provisions onboard the HS-6050. A
maximum of four ATA/33/66/100 IDE drives can connect to the
HS-6050 via CN6, CN7.
 CN6, CN7: Primary/Secondary IDE Connector
PIN Description PIN Description
1 RESET 2 GND
3 DATA 7 4 DATA 8
5 DATA 6 6 DATA 9
7 DATA 5 8 DATA 10
9 DATA 4 10 DATA 11
11 DATA 3 12 DATA 12
13 DATA 2 14 DATA 13
15 DATA 1 16 DATA 14
17 DATA 0 18 DATA 15
19 GND 20 N/C
21 PDREQ 22 GND
23 IOW# 24 GND
25 IOR# 26 GND
27 PIORDY 28 PR1PD1-
29 RPDACK- 30 GND
31 IRQ14/15 32 N/C
33 RPDA1- 34 PATA66
35 RPDA0- 36 RPDA2-
37 RPCS1- 38 RPCS3-
39 HDD ACTIVE 40 GND

14
3.10 Floppy Disk Drive Connector
The HS-6050 uses a standard 34-pin header connector, CN12, for
floppy disk drive connection. A total of two FDD drives may be
connected to CN12 at any given time.
 CN12: FDD Connector
PIN Description PIN Description
1 GND 2 RWC-
3 GND 4 N/C
5 GND 6 DS1-
7 GND 8 Index#
9 GND 10 Motor Enable A#
11 GND 12 Drive Select B#
13 GND 14 Drive Select A#
15 GND 16 Motor Enable B#
17 GND 18 Direction#
19 GND 20 Step#
21 GND 22 WD-
23 GND 24 WE-
25 GND 26 Track 0#
27 GND 28 WP-
29 GND 30 RDATA-
31 GND 32 HEAD-
33 GND 34 DSKCHG-