Boser HS-7002 User manual

HS-7002
800MHz FSB Pentium®4
Industrial Single Board Computer
•Full-size•800MHz FSB•DDR•GPIO•
•CRT/LVDS Panel•TV-Out•Dual Giga LAN•
•Audio•Serial ATA•ATA/33/66/100•
•RS-232/422/485•4 COM•PC/104•IrDA•
•USB2.0•WDT•H/W Monitor•
•PICMG Bus Industrial Single Board computer•

Copyright Disclaimers
The accuracy of contents in this manual has passed thorough checking and review
before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is
not liable for any infringements of patents or other rights resulting from its use. The
manufacturer will not be responsible for any direct, indirect, special,
incidental or consequential damages arising from the use of this product or
documentation, even if advised of the possibility of such damage(s).
This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation,
and storage of any form and means (i.e., electronic, mechanical, photocopying,
recording) of this document, in whole or partly, is prohibited, unless granted
permission by BOSER Technology Co., Ltd.
BOSER Technology Co., Ltd. reserves the right to change or improve the
contents of this document without due notice. BOSER Technology Co., Ltd.
assumes no responsibility for any errors or omissions that may appear in this
manual, nor does it make any commitment to update the information contained
herein.
T
T
Tr
r
ra
a
ad
d
de
e
em
m
ma
a
ar
r
rk
k
ks
s
s
BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
AMI is a registered trademark of AMI Software, Inc.
All other trademarks, products and or product names mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or
registered trademarks of their respective companies or owners.
© Copyright 2004 BOSER Technology Co., Ltd.
All Rights Reserved.
Edition 1.1, April 14, 2004

Table of Contents
Chapter 1 General Description……………………..1
1.1 Major Features ..............................................................2
1.2 Specifications ...............................................................3
1.3 Board Dimensions........................................................4
Chapter 2 Unpacking………………………………..5
2.1 Opening the Delivery Package....................................5
2.2 Inspection......................................................................5
Chapter 3 Hardware Installation…………………...7
3.1 Before Installation ........................................................7
3.2 Board Layout ................................................................8
3.3 Jumper List ...................................................................9
3.4 Connector List ..............................................................9
3.5 Configuring the CPU ..................................................10
3.6 System Memory ..........................................................10
3.7 VGA Controller............................................................10
3.8 Serial ATA Function ....................................................12
3.9 PCI E-IDE Drive Connector........................................13
3.10 Floppy Disk Drive Connector ....................................15
3.11 Serial Port Connectors...............................................16
3.12 IrDA Connector ...........................................................17
3.13 Parallel Connector......................................................18
3.14 Ethernet Connector ....................................................19
3.15 USB Connector ...........................................................19
3.16 CMOS Data Clear ........................................................20
3.17 Power and Fan Connectors.......................................20
3.18 Keyboard/Mouse Connector .....................................22
3.19 System Front Panel Connectors...............................22
3.20 Watchdog Timer..........................................................23
3.21 Audio Connectors ......................................................24
3.22 TV-Out Function..........................................................24
3.23 GPIO Connector..........................................................24
3.24 PC/104 Connectors.....................................................25

Chapter 4 Award BIOS Setup……………………..27
4.1 Starting Setup .............................................................27
4.2 Using Setup.................................................................28
4.3 Main Menu ...................................................................29
4.4 Standard CMOS Features ..........................................30
4.5 Advanced BIOS Features ..........................................31
4.6 Advanced Chipset Features ......................................32
4.7 Integrated Peripherals................................................33
4.8 Power Management Setup.........................................35
4.9 PnP/PCI Configurations .............................................36
4.10 PC Health Status.........................................................36
4.11 Frequency/Voltage Control........................................37
4.12 Load Fail-Safe Defaults..............................................37
4.13 Load Optimized Defaults ...........................................38
4.14 Set Supervisor/User Password .................................39
4.15 Save & Exit Setup .......................................................40
4.16 Exit Without Saving....................................................41
Chapter 5 Software Utilities……………………….43
5.1 IDE Driver Installation ................................................43
5.2 VGA Driver Installation...............................................47
5.3 LAN Driver Installation ...............................................50
5.4 Audio Driver Installation ............................................61
5.5 USB2.0 Driver Installation..........................................64

Safety Instructions
Integrated circuits on computer boards are sensitive to static electricity.
To avoid damaging chips from electrostatic discharge, observe the
following precautions:
 Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
 Before handling a board or integrated circuit, touch an unpainted portion
of the system unit chassis for a few seconds. This helps to discharge any
static electricity on your body.
 Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components. Fasten the ALLIGATOR
clip of the strap to the end of the shielded wire lead from a grounded
object. Please wear and connect the strap before handling the HS-7002
to protect yourself from the discharge of any static electricity through the
strap.
 Please use an anti-static pad when putting down any components or
parts or tools outside the computer. You may also use an anti-static bag
instead of the pad. Please inquire from your local supplier for additional
assistance in finding the necessary anti-static gadgets.
NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENT WITHOUT ALL NECESSARY ANTI-STATIC
PROTECTION.

1
Chapter 1
General Description
The HS-7002 is an Intel®82865GV/82801EB chipset-based board
designed for PICMG Bus PGA 478 Intel®Pentium®4 CPU with speed
of up to 3.2GHz CPU. The combination of these features makes the
HS-7002 an ideal all-in-one industrial single board computer.
Additional features include an enhanced I/O with CRT/LVDS Panel,
TV-Out, dual Giga LAN, audio, serial ATA, 4 COM port interface, and
more.
Its onboard ATA/33/66/100 connected to IDE drive interface
architecture allows the HS-7002 to support data transfers of 33, 66 or
100MB/sec. for each IDE drive connection. Designed with the Intel®
82865GV/82801EB core logic chipset, the board supports all PGA 478
Pentium®4 CPU series with Intel®Hyper-Threading Technology
clocking up to 3.2GHz. The display controller is Intel 82865GV with
1MB/8MB/16MB memory supporting CRT display up to 1600 x 1200 x
32-bit at 60Hz.
Serial ATA is the revolutionary ATA interface that provides scalable
performance for IDE device. With up to 150MB/sec. data transfer rate,
serial ATA is faster than the current parallel ATA and delivers superior
input/output performance. In addition, the serial ATA interface is
furnished with RAID 0/1 function for extra performance enhancement
and data protection.

2
System memory is also sufficient with the two DDR sockets that can
support DDR-266/333/400 up to 2GB. 800MHz FSB CPU can support
DDR-400, 533MHz FSB CPU, can support DDR-333, and 400MHz
FSB CPU can support DDR-266.
Additional onboard connectors include an advanced USB2.0 and IrDA
port providing faster data transmission, and two external RJ-45
connectors for use of one 100/1000 and one 10/100 OR two 10/100
Base-TX Ethernet interfaces.
1.1 Major Features
The HS-7002 comes with the following features:
 PGA 478 for Intel®Pentium®4 CPU with Hyper-Threading Technology
clocking up to 3.2GHz
 Supports 400MHz/533MHz/800MHz FSB
 Two DDR sockets with a max. capacity of 2GB
 Intel 82865GV/82801EB system chipset
 Winbond W83627 super I/O chipset x 2
 Intel®82865GV CRT display controller
 Intel®82562EZ 10/100 Based (or Intel®82547EI 100/1000 Based) and
Intel®82540 100/1000 Based LAN
 AC97 3D audio controller (optional)
 Supports Serial ATA controller
 Fast PCI ATA/33/66/100 IDE controller
 Four COM, seven USB2.0 connectors
 PC/104 Bus connector
 Supports Hardware Monitor
 Supports 8-bit General Purpose Input/Output
 Supports LVDS Panel interface (optional)
 Supports TV-Out function (optional)

3
1.2 Specifications

CPU: PGA 478 for Intel®Pentium®4 CPU with Hyper-Threading
Technology clocking up to 3.2GHz
 Bus Interface: PICMG Bus
 Front Side Bus: Supports 400MHz/533MHz/800MHz FSB
 Memory: Two DDR sockets supporting DDR-266/333/400 up to 2GB
 Chipset: Intel®82865GV/82801EB
 I/O Chipset: Winbond W83627 x 2
 ISA Bridge: ITE IT8888 (16-bit)
 GPIO: Supports 8-bit general purpose input/output port
 VGA: Intel®82865GV with 1MB/8MB/16MB (default) memory supporting
CRT display up to 1600 x 1200 x 32-bit at 60Hz

LVDS Panel: Supports LVDS Panel interface (optional)

TV-Out: Supports PAL or NTSC TV systems (optional)

LAN: One Intel®82562EZ 10/100 Based (or one Intel®82547EI
100/1000 Based) and one Intel®82540 100/1000 Based LAN
 Audio: AC97 3D audio controller (optional)
 Serial ATA: Intel ICH5 controller and with two ports supporting transfer
rate up to 150MB/sec.

IDE: Four IDE disk drives supporting ATA/33/66/100 and with transfer
rates of up to 33/66/100MB/sec.
 FDD: Supports up to two floppy disk drives
 Parallel: One enhanced bi-directional parallel port supporting
SPP/ECP/EPP

Serial Port: 16C550 UART-compatible RS-232/422/485 x 1 and RS-232
x 3 serial ports with 16-byte FIFO
 PC/104: PC/104 connector for 16-bit ISA Bus
 IrDA: One IrDA TX/RX header
 USB: Seven USB2.0 connectors, six internal and one external
 Keyboard/Mouse: PS/2 6-pin Mini DIN
 BIOS: Award PnP Flash BIOS
 Watchdog Timer: Software programmable time-out intervals from
1~256sec.

CMOS: Battery backup

Power Connector: One 4-pin and one 20-pin ATX power connector

Operating Temperature: 0~60°C

Hardware Monitor: Winbond W83627

Board Size: 33.8 x 12.1 cm

4
1.3 Board Dimensions

5
Chapter 2
Unpacking
2.1 Opening the Delivery Package
The HS-7002 is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.
2.2 Inspection
After unpacking the board, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.
Integrated circuits will sometimes come out of their sockets during
shipment. Make sure all integrated circuits, particularly the BIOS,
processor, memory modules, ROM-Disk, and keyboard controller chip
are firmly seated. The HS-7002 delivery package contains the following
items:

HS-7002 Board x 1
 Utility CD Disk x 1

Serial ATA flat cable x 1
 ATA/100 IDE flat cable x 2

FDD flat cable x 1
 Printer cable with bracket x 1

Two RS-232 COM Port cable with bracket x 2
 8-pin USB split type cable with bracket x 1

PS/2 KB/MS transfer cable x 1
 5-pin ATX power cable x 1

MIC/Audio 8-pin cable + 2 phone jacks x 1
 Jumper Bag x 1

User’s Manual

6
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the returned shipment of the product. In case you discover
any missing and/or damaged items from the list of items, please
contact your dealer immediately.

7
Chapter 3
Hardware Installation
This chapter provides the information on how to install the hardware
using the HS-7002. This chapter also contains information related to
jumper settings of switch, watchdog timer selection, etc.
3.1 Before Installation
After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to
take before you begin with your installation process.
1. Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper. (Set JP3 1-2)
2. Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections in this chapter for
the detailed information on the connectors.
3. Keep the manual and diskette in good condition for future
reference and use.
4. Make sure your power supply is you use is for P4 only. One of
4-pin connectors is for +12V lead which should be connected
to CN1 connector of the HS-7002.

8
3.2 Board Layout

9
3.3 Jumper List
Jumper Default Setting Setting Page
JP1 / JP2 / JP4 / JP5 Use RS-232 or RS-422/485 Select:
RS-232 2-3 Short 16
JP3 Clear CMOS: Normal Operation 1-2 Short 20
3.4 Connector List
Connector Definition Page
CN1 / CN5 4-pin/20-pin ATX Power Connectors 20
CN3 (1-3-5-7) Speaker Connector 22
CN3 (9-11) Reset Button Connector 22
CN3 (13-15) HDD LED Switch 22
CN3 (2-4-6-8) Power LED Connector 22
CN3 (10-12) 2-pin ATX Power ON/OFF Connector 22
CN3 (14-16) Green LED Connector 22
CN4 IrDA Connector 17
CN7 / CN6 Primary/Secondary IDE Connectors 13
CN21 / CN8 / CN12 / CN14 COM1~COM4 Connectors (5x2 header) 16
CN9 Parallel Connector 18
CN10 FDD Connector 15
CN11 RS-422/485 Connector (5x2 header) 16
CN13 / CN16 / CN17 USB2.0 Connectors 19
CN15 MIC In/Audio Out Connector 24
CN18 Dual RJ-45 Connector 19
CN19 External USB Connector 19
CN20 15-pin CRT Connector 10
CN22 PS/2 6-pin Mini DIN KB/MS Connector 22
CN23 5-pin ATX Power Connector 20
DM1 / DM2 DDR Sockets 10
J1 Inverter Power Connector 10
J2 LVDS Connector 10
J3 LVDS Connector 10
J5 TV-Out Connector 24
J6 / J7 Serial ATA Connector 12
J9 GPIO Connector 24
FN1 / FN2 / FN3 Fan Power Connector 20
PC2 / PC3 PC/104 64-pin/40-pin Connector 25

10
3.5 Configuring the CPU
The HS-7002 offers the convenience in CPU installation with its
auto-detect feature. After installing a new microprocessor onboard, the
HS-7002 automatically identifies the frequency and clock speed of the
installed microprocessor chip, thereby eliminating the need for user to
do additional CPU configuration or hardware settings related to it.
The HS-7002 provides 400MHz/533MHz/800MHz FSB, and the
all-in-one solution for the latest Intel®Pentium 4 processor with
800MHz FSB and Hyper-Threading Technology.
NOTE: CPU Vcore should be located in the range of 0.8375V to
1.6V, otherwise system won’t boot.
3.6 System Memory
The HS-7002 provides two DDR sockets at locations DM1 and DM2.
The maximum capacity of the onboard memory is 2GB. 800MHz FSB
CPU can support DDR-266/333/400, 533MHz FSB CPU can support
DDR-266/333, and 400MHz FSB CPU can support DDR-266.
FSB \ Memory CLK DDR-266 DDR-333 DDR-400
800MHz FSB Yes Yes Yes
533MHz FSB Yes Yes No
400MHz FSB Yes No No
3.7 VGA Controller
The onboard Intel®82865GV with 1MB/8MB/16MB (default) memory
supports CRT displays up to 1600 x 1200 x 32-bit. The HS-7002
provides two methods of connecting VGA device. CN20 offers a single
standard CRT connector (DB15). And J2, J3 offers LVDS Panel
connectors.

11
 CN20: 15-pin CRT Connector (DB15)
PIN Description PIN Description
1 Red 2 Green
3 Blue 4 N/C
5 GND 6 GND
7 GND 8 GND
9 N/C 10 GND
11 N/C 12 SDA
13 HSYNC 14 VSYNC
15 SCL
1
6
10
11
515
 J1: Inverter Power Connector
PIN Description
1 VCC12
2 VCC12
3 VCC5
4 ENABKL
5 ENAVDD
6 GND
VCC12 VCC12
VCC5
ENABKL
12 34 5
ENAVDD
6
GND
 J3: LVDS Panel Connector
PIN Description PIN Description
1 VCC3 2 VCC3
3 GND 4 GND
5 A0M 6 A0P
7 A1M 8 A1P
9 A2M 10 A2P
11 CLK1M 12 CLK1P
13 A3M 14 A3P
1
2
14
13
VCC3 GND A0M A1M A2M CLK1M
VCC3
GND
A0P A1P A2P
CLK1P
A3M
A3P
 J2: LVDS Panel Connector
PIN Description PIN Description
1 VCC3 2 VCC3
3 GND 4 GND
5 A4M 6 A4P
7 A5M 8 A5P
9 A6M 10 A6P
11 CLK2M 12 CLK2P
13 A7M 14 A7P
1
214
13
VCC3 GND A4M A5M A6M CLK2M
VCC3
GND
A4P A5P A6P
CLK2P
A7M
A7P

12
3.8 Serial ATA Function
You can connect the Serial ATA device to this connector which
provides you high speed transfer rates (150MB/sec.). If you wish to use
RAID function, please note that these two Serial ATA connectors just
support RAID0 and only compatible with WIN XP.
 J7: Serial ATA Connector
PIN Description
1 GND
2 SATA0TXP
3 SATA0TXN
4 GND
5 SATA0RXN
6 SATA0RXP
7 GND
GND
SATA0TXP
SATA0TXN
GND
17
SATA0RXN
SATA0RXP
GND
 J6: Serial ATA Connector
PIN Description
1 GND
2 SATA1TXP
3 SATA1TXN
4 GND
5 SATA1RXN
6 SATA1RXP
7 GND
GND
SATA1TXP
SATA1TXN
GND
17
SATA1RXN
SATA1RXP
GND
IDE and Serial ATA Device Configurations
Following are the IDE and Serial ATA device configurations supported
by Intel ICH5 specifications.
Native operating systems (OS) are Windows 2000/XP. ICH5 supports
a maximum of six devices using these OS.
Legacy OS are MS-DOS, Windows 95/98/Me/NT4.0. ICH5 supports a
maximum of four devices using these OS.
Operating System IDE Serial ATA
WIN 2000/XP Primary/Secondary Port0/Port1
Primary Port0/Port1
Secondary Port0/Port1
WIN 95/98/Me/NT4.0
Primary/Secondary ----

13
3.9 PCI E-IDE Drive Connector
CN7 and CN6 are standard 40-pin daisy-chain driver connectors that
serve the PCI E-IDE drive provisions onboard the HS-7002. A
maximum of four ATA/33/66/100 IDE drives can be connected to the
HS-7002 via CN7 and CN6.
 CN7: Primary IDE Connector
PIN Description PIN Description
1 RESET 2 GND
3 PDATA 7 4 PDATA 8
5 PDATA 6 6 PDATA 9
7 PDATA 5 8 PDATA 10
9 PDATA 4 10 PDATA 11
11 PDATA 3 12 PDATA 12
13 PDATA 2 14 PDATA 13
15 PDATA 1 16 PDATA 14
17 PDATA 0 18 PDATA 15
19 GND 20 N/C
21 PDREQ 22 GND
23 PIOW# 24 GND
25 PIOR# 26 GND
27 PIORDY 28 PR1PD1-
29 RPDACK- 30 GND
31 Interrupt 32 N/C
33 PDA1- 34 PATA66
35 PDA0- 36 PDA2-
37 PDCS1- 38 RPCS3-
39 HDD Active P 40 GND
1
240
39
3 5 7 9 17 19 21 23 25 27 29 31 33 11 13 15 35 37
46810 18 20 22 24 26 28 30 32 34
12 14 16 36 38

14
 CN6: Secondary IDE Connector
PIN Description PIN Description
1 RESET 2 GND
3 SDATA 7 4 SDATA 8
5 SDATA 6 6 SDATA 9
7 SDATA 5 8 SDATA 10
9 SDATA 4 10 SDATA 11
11 SDATA 3 12 SDATA 12
13 SDATA 2 14 SDATA 13
15 SDATA 1 16 SDATA 14
17 SDATA 0 18 SDATA 15
19 GND 20 N/C
21 SDREQ 22 GND
23 SIOW# 24 GND
25 SIOR# 26 GND
27 SIORDY 28 PR1SD1-
29 SDDACK- 30 GND
31 Interrupt 32 N/C
33 SDA1- 34 SATA66
35 SDA0- 36 SDA2-
37 SDCS1- 38 SDCS3-
39 HDD Active S 40 GND
1
240
39
3 5 7 9 17 19 21 23 25 27 29 31 33 11 13 15 35 37
46810 18 20 22 24 26 28 30 32 34
12 14 16 36 38